19-06-2024 What’s up all you beautiful GG and whoop Master Ciotti. 00:03:20 How does a cow chew lol. 00:04:06 On this stream……. 00:06:38 Got my Jungle Basher down to 22.5 grams, check your email for a fast easy lightweight antenna mod 00:10:45 Is 1202.5 11k motors a good play for motor upgrade on Mobula 8 03 over 1103 11k? ( Stator calculator www.vitroidfpv.com/tools/motors?motors=2207-2305.5 ) 00:15:36 The VCI 0702 motors in a V3 frame. Let’s fly a few batteries on it. 00:28:25 How you can check the health of your motors. 00:32:45 Is there a weight difference between the straight bt2.0 and the 90° bt 2.0? 00:34:41 I’m going to move out of Holland , sell my house. I want to buy in Thailand ...next to holy waterfall, not in tourist center, half way Chaing may. but to start fpv center over there , would it? 00:35:08 I posted in the discord the response Its FPV gave me when I asked them about frame weight after your mini rant, I think you'll get a kick out of the response. 00:46:00 What is you favorite brand of motors? 00:47:20 Can you put motor plugs on regular motor leads to install onto Mobula 8 aio? 00:48:22 What would cause no analog osd. Osd slider=on, analog is compiled into the BF build. When I view on box goggles I see FOXEER in the bottom left but same signal on hdz goggles has no text. 00:53:08 Let’s start round 3 on the Walksnail freestyle whoop. 00:56:56 Soldering wires on new pads. 01:04:31 Do you know of any 85mm frames with the post on the bottom? Have the V1 of that BetaFPV 2s board from a Cetus x and it doesn’t fit in anything. Currently glued post to a mob8. 01:05:25 figuring out how to Install the fc and Walksnail in the frame. 01:25:14 I tried changing osd to PAL and AUTO, no change. I have screenshots in general-nonsense. Maybe OSD chip is bad? like you said QA is bad on chips. 01:32:20 Installing grommet’s. 01:37:17 Installing the fc and Walksnail in the frame. 01:39:13 Teddy time. 01:40:52 Camera and canopy install. 01:46:58 I fixed the osd... I had a stray ground wire touching the yellow video wire on the neighboring FC pad. 01:47:10 Any tricks to keeping reny or peek screws from backing out? 01:53:25 What would cause a quad to bobble in the roll axis on takeoff and adding throttle. I replaced the FC board and jumped to Crossfire receiver. Previous quad config flew fine. Thoughts? Stay safe everyone and have fun flying
19-06-2024
What’s up all you beautiful GG and whoop Master Ciotti.
00:03:20 How does a cow chew lol.
00:04:06 On this stream…….
00:06:38 Got my Jungle Basher down to 22.5 grams, check your email for a fast easy lightweight antenna mod
00:10:45 Is 1202.5 11k motors a good play for motor upgrade on Mobula 8 03 over 1103 11k? ( Stator calculator www.vitroidfpv.com/tools/motors?motors=2207-2305.5 )
00:15:36 The VCI 0702 motors in a V3 frame. Let’s fly a few batteries on it.
00:28:25 How you can check the health of your motors.
00:32:45 Is there a weight difference between the straight bt2.0 and the 90° bt 2.0?
00:34:41 I’m going to move out of Holland , sell my house. I want to buy in Thailand ...next to holy waterfall, not in tourist center, half way Chaing may. but to start fpv center over there , would it?
00:35:08 I posted in the discord the response Its FPV gave me when I asked them about frame weight after your mini rant, I think you'll get a kick out of the response.
00:46:00 What is you favorite brand of motors?
00:47:20 Can you put motor plugs on regular motor leads to install onto Mobula 8 aio?
00:48:22 What would cause no analog osd. Osd slider=on, analog is compiled into the BF build. When I view on box goggles I see FOXEER in the bottom left but same signal on hdz goggles has no text.
00:53:08 Let’s start round 3 on the Walksnail freestyle whoop.
00:56:56 Soldering wires on new pads.
01:04:31 Do you know of any 85mm frames with the post on the bottom? Have the V1 of that BetaFPV 2s board from a Cetus x and it doesn’t fit in anything. Currently glued post to a mob8.
01:05:25 figuring out how to Install the fc and Walksnail in the frame.
01:25:14 I tried changing osd to PAL and AUTO, no change. I have screenshots in general-nonsense. Maybe OSD chip is bad? like you said QA is bad on chips.
01:32:20 Installing grommet’s.
01:37:17 Installing the fc and Walksnail in the frame.
01:39:13 Teddy time.
01:40:52 Camera and canopy install.
01:46:58 I fixed the osd... I had a stray ground wire touching the yellow video wire on the neighboring FC pad.
01:47:10 Any tricks to keeping reny or peek screws from backing out?
01:53:25 What would cause a quad to bobble in the roll axis on takeoff and adding throttle. I replaced the FC board and jumped to Crossfire receiver. Previous quad config flew fine. Thoughts?
Stay safe everyone and have fun flying
I learned with these smaller pads that tinning with high heat will also contribute to the pad lifting off 🥲
1:49:30. Quoting “The Dude”…