How to Install Pipe Boots|step by step| (DIY) Asphalt Shingle Roofs!

Aurum Roofing is a Full Service Residential and Commercial Roof Repair and Replacement Company. Serving Williamson, Travis and Surrounding Counties. 5 Star Rated with an Excellent Track Record for Customer Satisfaction. We specialize in installation of all roof types and materials, which include Asphalt Shingle, Tile, Metal and TPO Flat Roofing. We offer Free In-Home Consultations and Estimates backed with our 100% Customer Satisfaction Guarantee. Call us today for your Roofing Repair or Roof Replacement needs, we look forward to working with you! If you live in the Central Texas Area and would like more information about our services please feel free to call us anytime at [phone]
Or Visit us Online at- aurumroofing.com/
The project we will demonstrate today is roofing around a PVC plumbing boot flashing. But don't worry! These same steps also apply for any round type accessory, whether you´re roofing around an attic vent, furnace or pipe boot, it's all the same. The only difference is the size of cuts you will be making. We are also labeling the steps needed for this DIY project minute per minute below.
#AurumRoofing the best Central TX based Roofing Company!
Instagram- / aurumroofing
Follow us Twitter- / aurumroofing
Like us on Facebook- / aurumroofing
You could support our Channel by a Simple press of a button!
**Like, Share and Subscribe**
All donations are welcomed at: www.paypal.me/...
Items Needed- 0:21 - Hammer, Preferred Roof Seal, Caulk Gun, 1-¼’’ Roofing Hand Nails, Utility Knife with Hook Blade, Hand Held Drill, ¼’’ Hex Head Drill Bit, ¼’’ 1’’ Metal Roofing Screw with rubber gasket, shingles, and preferred roofing flashing.
#proroofer
Step 1: 0:38
Here I am installing the first cut shingle. As you make this cut, carefully cut around the round area and make sure your cut is no more than a 1/4” bigger than the round area. The closer it is, the more water proof it is. Then, nail a new shingle.
Step 2: 1:16
Since this is a 2” diameter PVC pipe, the pipe boot flashing has to be adjusted to fit a 2” PVC. The boot flashing should have the size marked for you so all you have to do is simply pull off the needed amount. Once your flashing is fitted, slide the boot through the pipe. The flashing should fit in tight and there should be no gaps between the PVC pipe and the rubbered area of the flashing.
Step 3: 1:39
Install 4-5 nails onto the flashing, as close to the edge as possible (make sure not to nail the bottom area, as this is where the screws go). You want your nails installed close to the edge. This ensures that the seal in the upcoming step properly covers the nails, without the need of over sealing. This will give you that extra water protection.
Step 4: 1:56
Cut the second shingle and make sure your cut is about 1/2” a part from the flashing. You don't want to make your cut too close to the flashing because you want the rain water to freely wash down the flashing sides. If your cut is too close, this will stop the water, therefore making it more difficult to freely run down. So always remember, 1/2”.
Step 5: 2:28
Once you know your cut is good, pre-fit the shingle to make sure it's going to fit, then remove it and install your seal on the vertical left, right and top side of the flashing. I do this, in this order, because it keeps the project clean and less messy. If you install the seal before you make your cuts, you´re going to find yourself with a messy work area and hands.
Step 6: 3:06
Now, since you know your cut fits, install the second shingle. Keep in mind that it's already sealed. Press down on shingle to ensure proper seal contact. Then nail the new shingles.
Step 7: 3:50
Cut the third shingle to fit around flashing (remember 1/2” around flashing) and then insert the new shingle. There is no need for seal as you already did that! Now nail down the third shingle.
Step 8: 5:08
Install 2 screws to the bottom of the flashing. In this case, we´re only using 2 screws but if your flashing is a wider accessory, use 3 or even 4 screws. Make sure to keep the screws about 2” away from the left and right vertical edges so you don't have to worry about water trying to sneak in through the screw holes. And, since the screws have a rubber gasket, there is no need to seal these exposed screws. ProTip: Use screws. Most roofers use regular roofing nails and then,they seal the exposed nail with a roofing seal. While this method works, I don´t recommend it as it only works temporarily. Once the seal deteriorates and falls off, or your nails back up, it leaves an open hole, making it vulnerable to leakage. With screws, you can be 100% certain you won´t have these issues.
Step 9*Optional: 5:30
Seal around work area, if needed. Since this project was a repair, I sealed the nail holes but if you are installing a new roof you can skip this step.
All done, Enjoy!
#diyroofing

[@GreatDataVideos]

Clearest, simplest video I've seen on installing roof pipe boots. Thanks!

[@Klatt1]

Is sealant needed where the top of the boot meets the vent pipe? Is the rubber there a good enough seal?

[@AurumRoofing]

On the rubber ring that wraps around the PVC you can if you'd like to. The flashing itself says 'no caulk' along the bottom edge meaning you don't need it. As long as its a tight fit and no gaps are left between the two you should be fine. One thing to keep in mind is that if you decide to seal that area I noticed some people like to use Polyurethane based seal on the ring I wouldn't use this type of seal in that area. I've notice that Polyurethane deteriorates the rubber prematurely, I would recommend you use your regular rubber roof cement or a clear silicon. Polyurethane is a great seal but only for metal to metal flashings or metal to concrete. Great question glad we could help! Stay tuned, before the weekend is over we will be uploading another How to roofing video (How-to remove a satellite dish off your Roof)