Schneider conext inverter understanding the AGS automatic generator start.

[@johnathanmann885]

What model generator are you using? Thanks

[@bbivens1990]

Could you use the AC2 input to tie to the grid and then control when you are connected to the grid with the generator control module?

[@tommyvvirs1731]

Hi, do you need to have the AGS module installed or does this unit act as an AGS? I have the same system and just installing a back up generator.

[@albertovelazquez4194]

How do I get that combox information that reads that information?

[@Collinsbond1]

hello CBI solar, i have a battery bank containing 80 units of trojan SAGM 06v 315AH batteries connected in series-parallel. and i use 2 units of context xw+ inverter 48v, please what max charge rate should the inverters be set?
Thank you

[@iamfound74]

Hello... Did you figure the max charge rate for your inverters? Looking into something similar myself. Thanks in advance...

[@raulmaldonado9264]

I have a generator aims 3200w but it is 120 I can connect it to the schneider 4048 system

[@bambino3162]

I have got a Scneider 4048 inverter, An Outback flex 80 and 8 12 v 200 AH Renogy gel batteries. I have checked the batteries and they are Ok. I have my OUTBACK flex at 60 . Something is strande my batterie volts drop )not used= from 54 v to 49 at a heart beat. Is there something I have to adjust at my inverter?

[@camosolarinc7697]

Sounds like you have a bad battery , please chech each battery under load and see if one is bad

[@raulmaldonado9264]

the investor has it 120 or 230?

[@zainzameerali9294]

How do you set the warm up mode time? I cant seem to find it in any of the settings.

[@camosolarinc7697]

Ya sorry Schneider put the warm up time in the Inverter and the only way is to have your computer talk to it on the LAN on the gateway or Combox

[@zainzameerali9294]

@@camosolarinc7697 thanks for clarifying that for me. Is there a guide on how to use the LAN to set up the warm up? I have the conext sw 4042 inverter. I cant find anything in the install or user guide and dont want to damage my diesel genset by having a load on start. Its -40 celisus here and even though i got the block heater pluged in it cant be good on the genset to not get a warm up.

[@earthenergyhex]

I would like to see how it was connected to the generator. What wires go where?

[@camosolarinc7697]

Each Genset is different and there way of starting

[@devonchiquita7619]

I have it set when my generator runs it seems like my batteries are getting really hot and it says it is full charge in only 2 min after gen starts and then the gen shuts off more concerned if I have my generator set up right

[@1beaverfrank]

if your batteries get hot you have a big problem how many Amp hour is your battery and how many amps are you pushing

[@earthenergyhex]

do you guys ever read the comments?

[@sharifdarwiche940]

HI I HAVE 8 L16H-AC TROJAN BATTERRY 6V AND Schneider conext inverter CAN U RECOMMEND ME THE BEST CHARGING SETTINGS FOR THIS MODEL?

[@1beaverfrank]

please got to your battery website and find what thay recomend

[@TerraFirmaX]

What's a BAT TREE?

[@slwool]

What generator do you use?

[@earthenergyhex]

I would like to know too

[@devonchiquita7619]

I have a 1000 amp hour agm wet filled battery bank would you know my correct settings

[@cbisolar1996]

Battery settings generally have to be obtained from the battery manufacturer. What is their make and model?

[@TAGUPNBLUE]

Start off with a 3-stage charge rate 60 amp bulk and float

[@jockpc]

i turn my ac on gos strait to charge how do i set dc prioroty

[@camosolarinc7697]

Im not understanding your Question or what you mean

[@TAGUPNBLUE]

charge rate up to high 70 amps will do

[@johnynozil3819]

How to sync Schneider 6048 to 220v

[@devonchiquita7619]

Gnb wet filled

[@cbisolar1996]

I see. Have you set up your schneider already and are worried about the settings being correct? Or are you setting it up fresh right now? Who sold you the system?