Good stuff my man, have a question on that pump. I'm curious how far will that shoot if you put a shooter tip on the wand ! I'm asking cause I do multi story apartment complexes and I've had several with their AC units in closets on their balconies. The AC causes rust runs down the building walls. I'm curious in distance because I'd like to use this setup for oxalic to pretreat the rust. I could use my current Softwash pump but I'd rather have an independent unit so I can run both at the same time. Your feedback on this would be much appreciated.
Hello great video, I just built my sprayer and everything was okay until it came to the priming because I noticed that it isn't pulling water. Any advice?
how do you clean it after done with sealing? does this work with any sealer /solvent based sealer? is the trigger going to get stuck open after first use?
@@ramdeo1978 I believe the pump has a pressure switch. Once it builds up pressure the pump stops so it won't continue to run. Then when pulling the trigger it releases the pressure and the pump will sense it and turn back on. It's like an RV/camper water pump to think of it that way.
1GPM is the threshold, anything higher can overflow the pavers and also higher will you make waste more Sealant than needed. Which at the point, you are losing money.
Thank you brother. I’m grateful!
Between this video, your wand setup vid ,and your truck setup you gained a new subscriber. 🎉
I appreciate it 🙏🙏🙏
Good stuff my man, have a question on that pump. I'm curious how far will that shoot if you put a shooter tip on the wand ! I'm asking cause I do multi story apartment complexes and I've had several with their AC units in closets on their balconies.
The AC causes rust runs down the building walls. I'm curious in distance because I'd like to use this setup for oxalic to pretreat the rust. I could use my current Softwash pump but I'd rather have an independent unit so I can run both at the same time.
Your feedback on this would be much appreciated.
thank you
*Can i use a 5.5gpm everflow pump n use a 55 barrel drum instead??Your setup Is ROCKING!!!*
Nice job.
Thank you! 🙏
Hello great video, I just built my sprayer and everything was okay until it came to the priming because I noticed that it isn't pulling water. Any advice?
Sir..(thank you!)..."when a sealing job is done..what do u do with the sealer "remaing" in the 3/8x25 ' line"?...jus curious and thx again
Just curious, why not a battery backpack sprayer
Awesome, thx. What is that angled nozzle that you are using?
Where is that wamd from or where do i find one similiar? Thanks
how do you clean it after done with sealing?
does this work with any sealer /solvent based sealer?
is the trigger going to get stuck open after first use?
I feel like solvent based sealers will dissolve that seal tape right away.
where is the gun from?
Where can I get the wand?
Where did you get that bulkhead at? I can’t find it at my homedepot?
See if another nearby store has it. If not, order it through their website.
amazon
Hey brother, is the pump and the battery the same voltage?
Yes, 12v.
@@FloridaXtremePw isn't the battery 18v and the pump 12v?
@@jmleon92 My apologies, the pump is 12v and I use a dewalt 20v for battery.
@@FloridaXtremePw when you hooked up the battery wouldn’t it keep spraying without pulling the trigger on the handle ?
@@ramdeo1978 I believe the pump has a pressure switch. Once it builds up pressure the pump stops so it won't continue to run. Then when pulling the trigger it releases the pressure and the pump will sense it and turn back on. It's like an RV/camper water pump to think of it that way.
Thanks for the info 😎🦾🤘
Anytime my brother! Get that 💵💵💵
How much to make me one
Hi why 1.0 gpm and not something higher?
1GPM is the threshold, anything higher can overflow the pavers and also higher will you make waste more Sealant than needed. Which at the point, you are losing money.
You should talk a little faster
Wooow slow down with the talking my mind can’t keep up