Thanks for showing you have patience for many of us don’t have, it shows that each one of us has a different gift and I can see that yours is patience thanks
Solmed Olenk: Thanks for the Video. Did the same thing which you showed and fixed the battery charger ( RC). It is charging 98-100%. did not have any flux so did not use any and heated for 2-3 seconds twice. My remote was showing only one light on the indicator, but now it is showing all the lights during charging. only request is if you can narrate during the video will be helpful for everyone. For me the visual was enough. Thanksssssssssssssss again.
This is just a temporary fix. Just buy the IC part number 2015CS. Install and your good. Part numbers CW2015CS, CW2015CSAD, & TDFN8 will also work if you can't find 2015CS.
Thank you very much .. with your tutorial I solved the problem of charging the Pantom 4 Pro plus battery 100% .... you are a great ...with estimates Roberto
great video. I thought about that with the flux to. What temperature do you set the heat gun to? liquid melting point of tin is between 218 - 230 degrees celcius, starting at 183 - 190 getting mushy. and how long do you hold it? I'm concerned about breaking the electronic parts or melt it loose.
Very good video. I am off to a bad start though. :) Cannot even remove the cover at 3:09 What screwdriver/torx? is that. The instruments I have do not fit. Can you enlighten me please? Thanks!
Not required just use a hair dryer for 1/2 hour while blowing on the led side while turned on and keep turning it on if it shuts down then charge I promise this works
Same remote, same problem. Thanks a lot! 300 C° or more? Two days later...........Had to do it two times. My heat gun was at 330 C°. Seems it works now.
At 7:12 why do you skip so much of the work and not show how you removed that piece? I was following you step by step and it was all going great until you jumped to you doing something steps ahead? Is there something we are missing here?
Amigo o controle do meu drone spark Também não tá conectando se eu fizer este processo ele pode reconectar nava mente? E como vou saber qual o lugar certo pra fazer esta ligação no controle do Spark grande abraço me ajuda
Thanks for showing you have patience for many of us don’t have, it shows that each one of us has a different gift and I can see that yours is patience thanks
Solmed Olenk: Thanks for the Video. Did the same thing which you showed and fixed the battery charger ( RC). It is charging 98-100%. did not have any flux so did not use any and heated for 2-3 seconds twice. My remote was showing only one light on the indicator, but now it is showing all the lights during charging. only request is if you can narrate during the video will be helpful for everyone. For me the visual was enough. Thanksssssssssssssss again.
This is just a temporary fix. Just buy the IC part number 2015CS. Install and your good. Part numbers CW2015CS, CW2015CSAD, & TDFN8 will also work if you can't find 2015CS.
Me.ppdes mandar la descripción del repuesto y como lo isites gracias broo
Thank you very much .. with your tutorial I solved the problem of charging the Pantom 4 Pro plus battery 100% .... you are a great ...with estimates Roberto
Good job bro..👍🏻🙏🏻
Thank you information helpful
A very useful video. I found it necessary to mute the unpleasant music.
Sorry Karen for the music
great video. I thought about that with the flux to. What temperature do you set the heat gun to? liquid melting point of tin is between 218 - 230 degrees celcius, starting at 183 - 190 getting mushy. and how long do you hold it? I'm concerned about breaking the electronic parts or melt it loose.
Thank you, this fixed the problem!
Very good video. I am off to a bad start though. :) Cannot even remove the cover at 3:09 What screwdriver/torx? is that. The instruments I have do not fit. Can you enlighten me please? Thanks!
Hi, what are the 2 points you are touching with the tweezers on the board?
Worked for me thank you very much.
You're welcome 💪💪
What is the temperature of heating and how long you did it?
Not required just use a hair dryer for 1/2 hour while blowing on the led side while turned on and keep turning it on if it shuts down then charge I promise this works
Very good bro
Do you recommend the same solution you did If the controller doesn’t fully charging (up to 81% and draining down quickly) ?
dreadful music, how can you concentrate with that racket
Same remote, same problem. Thanks a lot! 300 C° or more? Two days later...........Had to do it two times. My heat gun was at 330 C°. Seems it works now.
Hello, 330° ok but you heat it for how long?
@@MrDimibass As far as I remember, it was 30 seconds. But after two battery loads, I had the same problem. In the meantime I bought a used remote.
Hi, thanks for video. What was the solution you added after the heat reflow?
Sir howmuch hitting ??nd howmuch time to hiting this ic ?
Sir phantom 4 pro+ 2.0 me siganel vik antina Arjest Btata hai to kya kre
thanks it's work's
Baru mantap ne 👏👏👍👍
At 7:12 why do you skip so much of the work and not show how you removed that piece? I was following you step by step and it was all going great until you jumped to you doing something steps ahead? Is there something we are missing here?
Please see again my video..i'm not remove or replacement ic..but rehot only.
what radio defect you fixed could help me and the same as mine
Sir phantom 4 pro siganel vik antina Arjest btata hai to kya kre
Amigo o controle do meu drone spark Também não tá conectando se eu fizer este processo ele pode reconectar nava mente? E como vou saber qual o lugar certo pra fazer esta ligação no controle do Spark grande abraço me ajuda
i don't understand.. please use english
mun teu daek full ngecasna bisa ngomean teu kang
Diply and tuch don't work can help me
query: what liquid do you add with the brush? Thank you
Flux
THANK YOU MY CONTROLLER COMPLETELY DEAD AFTER FELLOW YOUR VIDEO... WTF
Remote Phantom 4 pro + sy jg sm pnyakitnya om, sdh prnh dbawa service 2x, msh ttp gk bs normal
Are bhai ye number to h hi nhi whatsApp pr
Remote phantom saya juga Sama...
Sudah selesai om..?
@@solmedolenk582 Sampai sekarang blm diperbaiki...
Очень долгое видео.Можно было бы местами ускорить,обрезать лишнее,короче сократить до 10 минут.Ибо люди не любят долгие поучающие ролики!
G bisa charge mati lampu mereun haha
Secara teori kenapa bisa begitu min?
Koi contact number ho to doo