Orientation and Configuration of Danfoss VLT FC 051/ FC 360 / FC 101 Drives || Digicon Automation
HTML-код
- Опубликовано: 25 авг 2024
- || Three wire start stop with speed POT application ||
Parameter list for Three wire start stop with speed POT application :
1-20 = Motor Power [kW] [hp]
1-22 = Motor Voltage
1-23 = Motor Frequency
1-24 = Motor current
1-25 = Motor Nominal Speed
3-15 = [ 1 ] Analog Input 53
3-16 = [ 0 ] No function
3-41 = Acceleration Time
3-42 = Deceleration Time
5-10 = [ 9 ] Latched start
5-12 = [ 6 ] Stop inverse
![[Tutorial] Danfoss FC51 Setting](http://i.ytimg.com/vi/rYj0XnknJ3c/mqdefault.jpg)
![[Tutorial] Danfoss FC51 Setting](/img/tr.png)
thanks sir..very important knowledge.....SV Electronnics Nanded maharashtra
Very very nice sir.
Very Good working
yes good
very helpful video
👍👍❤ thanks frind
Hello
Thanks for the wonderful video. I'm using Danfoss VLT HVAC Basic Drive FC 101 and want to use pushbutton for speed up and down. But I noticed there is no terminal 33. As per the manuals, only model Danfoss VLT micro drive FC 51 and VLT automaton drive have terminal 33. Please advise how to use pushbutton for speed up and down for Danfoss VLT HVAC Basic Drive FC 101.
Thank You
So good
i want to know about terminal 20 and 33 setting i am using this terminal for over limit
Which language is this?
Hindi
Good
How can we replace it with old drive of commercial trademill ??
We have Danfoss ac Drives FC 51 -micro drives ASD ENGINEERING DELHI-92
AM DL Sharma From Rajasthan Am Use FC 360 Drive .
Our issue
We Use Control card In 5.5 hp DRIVE then Run The Drive But Used this Control Card in 1.5 kw 2hp then COME Al 38
Same Control Card Run in 5.5 hp But 2 hp Not Run come Al 38
so Plz Tell How to Remove Al 38 In Control Card.
Alarm 38 for Internal fault, You need to update the software version of VFD to reset this Alarm
Hi Dear
How to get the registers addresses of the fc101 vfd
Nice video 👍
Hi good morning
Dear i have danfoss FCM 305 - with worming indicated local stop - i tried every thing - can you help
Please guide on automation drive.
How to connect digital scaling meter and program in danfoss vfd
Hello my friend, well done for posting
is there any ready signal form vfd for programing with plc?
Sir humari company mai danfoss vfd ,wo phase loss dikhata hai bar bar ,humne output cables aur motor check ki okay hai,shi chalti h lekin 2 -3 gnte m fault aata hai isko reset kese kre
Sir jaise Ham bahar se start stop push button use karnah aur drive ka potential use karna hai
Ek problem hai
Please help me
Danfoss fc360 hai usme ek. Warning 7aa raha hai
Danfoss me multistage speed ke baare me video banaye.
Direction of rotation parameter which one?
Forward or Reverse or Both
Thanks
Buen día. Será que me podrías apoyar con los parámetros y conexión que debería utilizar para un alternado de dos variadores con transductor? Es decir que encienda uno, se para y encienda el segundo, luego se pare y encienda nuevamente el primero etc
🙏🏻
Thanks you, great video! I need to run a motor up to 70 Hz using an external potentiometer, and i can't do it. 3-15 parameter is in "1" already. The motor gets to 50 Hz. Do you know what could be happenning? Thanks!
thank you..
You need to set three parameters...as per below,
3-03 = 70 Hz
4-14 = 70 Hz
6-15 = 70 Hz
@@DIGICONAUTOMATION Thank you very much!
@@DIGICONAUTOMATIONbut sir motor may get hot ,I think
Brak Ragister ka use kha kiya jata hy 😊
Sir delta drive ke auto/manual ckt ke bare me bi btaoge.sir plz
Dear sir
whats difrants in - FC -051, FC360 and FC - 101
FC101 Refrigeration Drive most used in chillers, Air-conditioning,
FC051 is Small Application used automachine drive,
FC360 is Fan application and Pumb application Specifically used and number of digital input is high.
Basic different is Different firmware and parameters used in the drive
You want any help please Call 8637641293 I will guide you,
Currently I am working in danfoss drives..
Frequency kaise badha te hain
Sir. Who is relay trip parameters in vlt micro drive 51
Sir fc51 drive mein samne display mein rpm kaise dekhenge.
hi im velu from sun controls bangalofre . i have one doubt my danfoss vfd showing overcurrent error without conneting motor wht is the issu plesae help me
Okay sir, you have to do factory reset your VFD.
ruclips.net/video/7RAzQeYtttY/видео.html
Thank u for reply...one more doubt if I do factory reset all saved data will be delete or only alarm will delete?
@@suncontrols1884 All data will be deleted
dear sir,
in circuit diagram u have shown that latched start to terminal no 12,do it means a continuous nc puls should be given at point 12 or one time nc pulse is required
Terminal 12 is for +24V supply, where for latched start we used a terminal no. 18
Friend,really terminal 12 is a source of +24vdc
I have 7.5 hp danfoss fc51 and it taking 4 to 20 ma frequency command but after power trip vfd is not taking 4 to 20 ma command and there is any alarm and i have connected 55 and 60 number terminals. Please suggest me how do i check and what is parameters of 4 to 20 ma for plc or pid and 0 to 10 volt for 10k port.
Dear friend,
According to me,
For 4-20ma
3-15......[2]
For start command you can select 5-10....[8]
6-22....4ma
6-23...20 ma
Rest keep default settings
Connection diagram:
Term. 60 ...... +
Term.55......... -
Connection of start command
Between term.12 and Terminal 18.....NO contact.
Rest on your feedback
sir muje motor ki frequency badaani hai konsa parameter hai
Parameter 3-03 = Max. frequency that you want
Parameter 4-14 = Max. frequency that you want
Dear sir,
You explaination was very simple and good.
I am facing one similar problem at site can you please help me out.
When i am starting the motor it's frequency is directly going to 50hz.
I want to control the frequency from 20hz and as vtg increases frequency should also increase.
Can you please guide me to do the settings for the frequency.
अगर आप FC 51 use kar rahe hai to
Parameter
4-12........motor speed low limit
Aur 3-02......minimum reference check check kare
Inme aap 50hz rakhe hue hai.isko 0 ya kuchh rakhe jisse aap start Karna chahte hai.
Vlt 5000 ka revars and farvard fara mitar sir
Hello mr.can you make totorial vidio how seting parameters vfd motor dc for me..?
Lock or unlock kaise kiya jaaye
Dear Sir
Danfoss drive FC 102
This driver problem is ....
Short circuit (16A) on display
How to solve this problem
Plz help me sir
Please send your mail I'd
Sanjay Aher
Sir Dc Se chalane keley kaya program danlna padega
Kitne volt DC?
If you have 3 * 560vdc ,you give to Drive get Ac output
Frequency wrong show ho raha
ID Run ka kya parameter ha sir
Hi there! I am interested on the Digicon Start/Stop panel. Does it have a part number or can you tell me where to buy it? Best regards, Istvan
Over load production setting
Password laga ho to kai se parameter set kare ge
Wiring vfd to motor
Vlt 2800 parameter setting
You want Any Special parameter, Which application parameter.
S,haran
Kisi Koo old VFD chaiye too muje reply karke mujse baat kar skte hoo
En español por fa
Sir aap ka no milega kya
Port ka parameters tobbataye hi nahi
For POT, If u connect the wire on terminal 53 then set [1] on parameter 3-15..
@@DIGICONAUTOMATION thanks sir
@@DIGICONAUTOMATION vfd037M43A display pe hpf dhikha raha hai to kaya problem hai
@@chaudharykaif Can u share a picture ?
Picture kis pe share karo