How To Stop Your Nitro Car From Stalling When You Brake!
HTML-код
- Опубликовано: 31 дек 2022
- I hope this helps!
Please check out my Wish list and anything you may send me will leave me eternally grateful ;)
Rusty's Amazon Wish List: amzn.eu/3TJm7Rf
You can help me make better content by donating Via PayPal as a gift to RustySkullProductions@hotmail.com!
Or you can use this link: paypal.me/RustySkull
Every penny that is donated will go into making good quality videos for all my loyal subscribers!
Many thanks to you all :)
#Nitro #RC #RCNitro 
Развлечения
Dead on advice. My Traxxas Revo 3.3 stalls every-time a spin out or hard brake. My idle was closed. Gonna try it after my repair…. After I finally took off the filter, I notice this. I just found out this vid which confirms my issue.
Nice one dude glad you got it worked out!
@@HaggardRC Love your channel. But why does she fire up every time with a blocked idle…
@@Drumbone71Because when you open the throttle it's not closed anymore. 😄
@@HaggardRC I get that but might have been a little open. She fired up and idled with no throttle input. Oh the tick gap is air intake. Not fuel. Duhh. I get it now….Thanks Man.
I had the same problem on my FXT Zorro and adjusting the idle screw sorted it. Got that advice from a previous video you put up, so cheers. 👍😁
You’re welcome 😄
Great video. Very informative. Thank you very much and have a great day
Thanks a lot mate this video really helped a lot, I'm new with RC nitro cars, had no idea about this, but this really explained a lot about my car.
You’re welcome :)
same bro👍
Thanks again for another very informative video see my hyper ten petrol 1/10 scale it was a two speed see when it hit that 2nd gear i couldn't control it lol
great info man thanks
Ty this is so helpful
Thanks bro I am the new nitro owner to learn from this video. I got brakes without it stalling on me so thanks.
You’re welcome :)
I tried to do it for the first time on my wr8 last week, totaly messed up the enigne...... 1 .25Lt of fuel and about 4 hours later I managed to bring her back to life!!
The trick is to make tiny tiny adjutmesnts, i was spinning it round like a top, but tiny tiny movements! Every time you richen or lean the low speed you must make a tiny opposite adjustment to the idle screw. tiny tiny adustments.
Or another thing if it stops while driving it could be the transmitter with the receiver that it needs to be binded set up.
New Vid nice 👍👍👍👍
Mate I've had with my annsman 😂 I've had perfect then next day it needs redoing , I'm just at the stage where nitro is just a waste of time
Thank you so much
There could be another reason to, the clutch bearings could be bust and binding so I would check those to, if the clutch is binding your engine will stall out when you brake.
@@mtadave6702 I brought it brand new a few months ago
@@timothyhatcher8673 clutch bearing take a hammering and usually don't take well to water m8, they can seize up on you when your not using the car. Then when you go again they break. The factory setting should have already been set on the carb, but sometimes manufacturers don't bother. Push your truck along with your hand along the floor, if there's a squeeky noise or grinding noise then it's the bearings that are shot and you'll have to change them. I buy clutch bearings in bulk off ebay for all my different nitros.
@@mtadave6702 thank you I will try that in the morning
My nitro car idle screw/tickover screw doesn’t work. When I turn it it doesn’t open or close the gap apart from when it is fully screwed in it opens the gap a bit. I’ve tried unscrewing it fully and trying to fit it back in the slot thinking that it has slipped out of it but that hasn’t worked and I would appreciate some help as there are no other tutorials for this.
If you can wait a few days I can try to make a video showing how it works and what could be the problem.
Thank you that would be appreciated. Thanks for the quick reply and I am subscribed now
As a fellow nitro noob I knew I'd find the answer here!
And did you?
@@HaggardRC I sure did! The car is a mess but now that I have this much sorted. I can get everything else dialed in
"or a turd as some someone else decided to call it" 😂😂
I am new to the hobby to and I have one question also. Why does one engine tic over go back to what is normal after a run
And then another one the exact same engine and needle settings
Both have the same gap and tune
Yet one works as intended and the other engine just can’t hold a tune it always holds the high revs never idles back to proper tic over
Yet the other one idles up properly and drops back to ticover within the proper alloyed few seconds after a high speed pass.
I am leaning towards my change in fuel and why I say this is as follows
The bug and my local hobby shop 25% 10 % oil just sucked and did not tune worth a crap.
That fuel I added oil to then I worked somewhat better but the tune was still wak
Now after researching and buying fuel with 16% oil I am noticing the tune is spot on
Do you think my location and or old fuels are what brings me here to ask such questions
Do you find this to make such a big difference in tuning
Or old bad gas is hard to tune
My hobby shop dude said the fuel was old stock how old 🤷♂️
But like I said the 16% oil that works like a charm
I’m still learning that’s a fact
Thanks for what you do bro you rock
Happy new year dude 🥳👊😎
Well if you have two identical engines and one is having issues then maybe it has an air leak or something like that it a slightly blocked jet? Have you looked at the carb?
@@HaggardRC
It appears the same with no visible difference with anything. The only thing I can think of is that one car has a 3 needle carb Mabey it is not set properly in the mid needle 🤷♂️really I’m unsure.
The one that’s not right the engine is rebuilt and rips. It’s just now sometimes it would shut off like it was almost running out of fuel
Almost as of the mid range of the carb is lean 🤷♂️but that I can’t say for sure
Hey Qq,
I have a slight concern bout my traxxes nitro rustler, it work's grated but lately I found that at the hi trottle it screams like normal but not going that fast..... ?
Could be a clutch issue then dude. Also if it has a slipper clutch they can come loose and slip too much. Causing your exact symptoms 🤘🏻😁
I have a 18. engine or 1.8 size nitro engine. I really need help please.
What’s the problem?
hey haggard i snapped my pull start off can i buy a new pull start or do i have to buy a whole new engine??
Yeah you can buy pull starts I usually buy two so I have a spare :)
@@HaggardRC yeah i bought 2 but its a bit awkward to get to my pull start are they hard to put on
Nah they’re easy, take the engine out then you can get to the 3 or 4 bolts holding the pull start on 😃
Hi, the wheels on my nitro keep spinning when starting it up, can you tell me what the problem is please?
Turn the tick over down 👍🏻
If the wheels are off the ground it’s normal for them to spin.
@@HaggardRC how do you turn it down?... is there anywhere i can text you, so I can send you a picture and pick your brains, I've got parts missing and don't know what it is I'm looking for to buy the parts.
Petrol RC Car With *Two Gears* Remote Control Car With STARTER KIT & NITRO FUEL this is the car I have it doesn't give me much information I do apologise for not explaining properly
Why does my nitro spit out fuel from the glow plug?😅
It’s not sealing, maybe you’ve lost the copper washer 😅
@@HaggardRC the washer is there.lol. I'm going to try a new washer and see if that works if not I'll take the top off and clean it lol 😜
Was you still Pissed from NY Eve when you Wrote the Video Title?
I don't drink I have autism and dyslexia problem and have trouble with trying to explain things
Haha Dee that’s funny I hadn’t noticed that I’ve fixed it now 😂
18 fucking minutes for 3 minutes of important stuff
Glad you enjoyed it 👌🏻😂