As someone who has done VW beetle restoration, I made a template with door hinges which I bolted in place before welding the pieces back in and that made sure the door fitted, good job you learning as I did along the way!
Man your videos are literally treasure. Visualisation of the process makes a huge difference when one's going for such an endeavour! Thank you for the knowledge man!
Hate to be an armchair coach so I appoligize for doing it. Before taking anything apart put your bracing in the interior to stabilize the body and leave it in place until all work is done. Any work around doors do it with the door in place, thats what you did on the drivers side. When parts are tacked in then remove the door. Excellent frame of mind CT you are moving ahead in leaps and bounds. Cheers.
@@novavolks9652 I use gas for pannels and mig for structural. Have not tried tig yet. I like gas for cut and but because it leaves the metal pliable, tig should as well.
Have now watched every episode up to this one. I greatly admire your steady progress. Speach is clear and concise, just at the right speed.🎉 i recently compleated my restoration of a Morris minor convertible, and I had the same problems that you are finding. It's an enormous learning curve, and it took 2 years. Did part-time courses at the local tec, to learn techniques, well worth the time spent. 🎉🎉🎉 i had to buy very thin shims to get door adjustments, correct.
We all have fun days like this. Watch out with rear quarter panel patch i had trouble fitting up the running boards. But we all live and learn. Nothing ventured nothing gained. Measure twice cut once. Enjoying watching your chanel Thanks.
always remember to measure twice and cut once, a next thing when you offer up the doors make sure the car is sitting on its own weight and not being jacked up that will throw the measurements off when you cut and paste...love the channel keep it up.
^^^^ This. Measure, measure, measure and make notes. And use a straight edge where you can on flat surfaces such as the vertical hinge panel to keep the panels straight. True, you do not jack up a corner of the car to help aligning and welding in panels. It needs to be sitting level on all fours to get an accurate fit with the body shell at rest. Welding in the hinge panel on the left side with the floor jacked up most likely lead to the door being too low once the jack was removed. Just helpful tips here.
Really enjoy this rebuild series I have been scared to buy a bug with rust but watch you I believe I can do it your not rhe only one learning from your mistakes
I have to say CT that looking back to when I first started looking at your videos, the 1962 VW van (Rusty?),you have made SUPERB progress and your skill now is beyond what most DIY car owners possess. Well done young feller, thanks for sharing and best regards from Ireland.
Well done for your persistence, I suppose that is what real life is about. We are faced with so many challenges in life. But we need to be persistent and not to give up. Life is not easy but we need to make it work.......
Messing up is part of the learning process. I am working on installing a fuel level sender and fuel gauge in my '59 bug and I ruined the 1st tank. I drilled the hole in the shallow part of the tank and now the sender doesn't fit. I'm not sour about it but it was all due to doing things the lazy way. Oh well. I'm already on my second tank. Waiting for the self drilling screws. Best of luck. I love these videos.
For all the amount of metal work you’ve done, I think you’re doing great! I’m amazed how the doors seems to close well, and that’s without even finishing the whole metal work on the back portion of the car!👌😎👍
Thanks for your video, as I have seen other sites that are perfect, not realistic, would rather watch the mistakes, the process, and still getting job done we all. make mistakes.
It takes a team to do it right. We are all in this together. I have been working on a type 181 for almost eight years so close. With very little help. Go for it CT ! Learn as we all do.
Great job on pushing through and adapting to the situation of the metal work! Love seeing u dig in and get it done. Can’t wait to see the Porsche get done as well. Enjoy your thanksgiving!
I watch so much car content on RUclips where the only issues that rise up seem to be manufactured. I could feel your frustration after fitting the door the second time and still not being successful. Like most of us even remotely brave enough to try this as amatures would. You are way better than me but you give me hope that my skills will eventually get me to where I need to be.
CT, what I find interesting about your channel is that it’s not an “instruction”. But rather an “adventure”. Would hardly be the same if you were an expert. You pay the rent, buy the cars, the tools and share the struggle! I look forward to many more rough rides….
Congrats for sharing with us candid learning process. If I were there, I’d suggest: keep a welded bar holding body wide near B column; use the jack to hold/lift the door to screw/adjust; use vise grips holding new insert to car, chek exact position several times and cut simultaneously new and old part in a single cut. Remove excess and weld definitive and precisely at the single cut. Advising is easy…make it happen is for the heroes! Best regards from Brazil.
friend now if this side gave you a lot of work, I think it is better to repair the lower part of that door, and so this project continues with most of its original parts, dude, you have already come a long way with this project and you are excellently very advance, have a little faith in how you are doing it, and don't let rust win you over. big hug from the southeast of Mexico. Blessings.
This is fantastic, sir! You are turning into an expert right before our very eyes. You are taking the time to measure and are doing excellent work. The content of your videos has improved EXPONENTIALLY since you started really getting into it. You have a great attitude that will prove invaluable and you’ll gain the confidence to tackle more and more complex projects. Re the alignment of the passenger door; remember you are still missing the metal panel inside the wheel well that will reinforce the area.
I like it when somebody is willing to show the mistakes right in the video because that's exactly what I'd be up against if it were me. Would have been so easy to cut to a polished repair and keep moving like crap like that don't happen.
Le está quedando biensísimo su RECONSTRUCCIÓN DE SU AÑORADO "VOCHO" SE NOTA QUE LO ESTÁ HACIENDO CON EMPEÑO, MUCHO SACRIFICIO Y SOBRE TODO CON AMOR ¡BUENA SUERTE
I hate it when I try to put the horse before the cart, drives me nuts, and all because I was thinking 4 steps ahead before making sure what I was doing was right. But that's how you learn, by making your own mistakes the having to fix them. Nice job in the end you got where it was supposed to be, and that's all that counts!!
I would have dropped at least one screw into the a-pillar! Use pieces of the donor door to patch up the bottom of the original door and keep that awesome patina! Great watching as always! Keep up the good work and attitude!
Good video! Good on you for showing your journey on this - "metal is clay" add to that "measure twice, cut once" ;-) Keep your original doors and fix them up - you have the skills, you can do it 🤜
Tenho um VW 74. Gostaria de ter sua coragem de colocar a mão na massa como o senhor. Admiro sua persistência para fazer este trabalho só e ainda nos proporcionar este aprendizado e divertimento. Parabéns e obrigado.
ct when you do those repairs use part of the old pillar to sleeve inside trim the edges till it slides inside then tack weld it to hold it it will make it a stronger repair rather than butt weld as they tend to crack in areas like that under stress because you had nothing attached to the heater channel it allowed it to move up on you first attempt
Congrats: All the sh't happens - und CT is staying in rather fine mood. My own patience would not be enough for such incidents 😭... Keep welding and have a good success and make the whole project perfect sooner or later
Mate I told you when you did other side use your trolly jack to hold your door up instead of struggling to hold door and try to fit a screw its not hard work smart not hard you will get it and try practicing on your bench to tack two peices of metal play with setting wire speed and heat you will get there great video 👍👍
Many people like to talk about the 1967 as a one year car, but nearly every year of Beetle was a one year car. VW made incremental improvements of the Beetle every year, some years the differences are obvious like the 1967 some years are more subtle, then you have the half year improvements, where they added a feature for 1965 near the end of the 1964 model run. So, that door could be a 65, or not depending whether VW was introducing an improvement.
You should of removed the brace and placed it higher between the middle pillar and the door pillar otherwise your geometry 📐 will be out. (So you’ve gathered) 😂 Also whenever you are replacing a rusty part. Place the new panel over the top using vice grips or clamps then cut once. You’ll then have the perfect cut for the replacement panel. The door pillar is a structural area so you should use a piece of the old panel behind the new and old to bond them together thus making that area stronger. I hope you listen to everybody’s advice and continue to make this build great 👍🏻
I’m really worried, REALLY worried, that you’re going to think that A pillar is good to go. My friend, it is not. That is a structural connection, and the critical interface is a series of butt-welds that can’t be sound enough to keep the car together. Someone else has mentioned using stiffeners. Doublers, stiffeners, back-side patches…whatever you call it, it needs to be used to ensure your Bug will hold together. Please weld in additional plates to make that A pillar stronger than original.
@@CTmoog thank you!!! I really enjoy watching you learn as you go! I was truly worried, though, that you’d made a decision that might’ve put your butt in danger my friend. Can I also suggest you gets some 20 or 30 thousandths skin and practice your butt welds. Please keep in mind that just because you can buttweld skins together, you can’t necessarily return a patched area to the rigidity and strength of the original formed, solid areas like the A pillar foot on the tunnel. Stay patient, my friend!
This is the best comment ever. I don't know anything about restoration, but when I saw that the welds (in one case two slightly separated) on the structural post without any reinforcement I thought that I don't buy or drive this car... :9 I said it with a better vibe ;), bro !!!!
Admire the work that you're doing, but this comment is dead right. The A Post is a vital structural component in the event of a collision and any reduction in its integrity could make the difference between surviving or not.
Why don't you cut the good part off the new door and stitch it to the bottom of the original door like a repair panel? You would have the same good fit and most of the patina that way.
In my opinion, it would be nice to have the original passenger door in place. It is a hard task to save it, but the original rusted paint would give it an excellent look and feel, and this door is the original. Every beetle likes its original parts. :) And after the restoration of the body there would not have to paint.
Hey mate. It really looks like the best thing to do would be to just cut the bottom 6 inches off both doors and swap them over. Then all you'd have to do would be to blend the paint on the bottom bit so it wasn't red. It would be so great to keep the matching patina of the old door, wouldn't it? By the way I'm loving your vids - the way you face a mistake with a sigh and a laugh, then just carry on is really great. Many weaker men (like me) would've kicked the welder across the garage and gone for a pint. Well done mate, keep it up, we're all with you.
At that point another new part would have been the best. Putting the whole door, shimming it and tack pointing the part, somehow, somewhere. You could even brace the new part to whatever accesible and weldable section of the body. But as you said, it's a learning process. Hard to be in your shoes.
I think you will need to cut the bottom of the a pillar back off and put a jack under the door then tack it in the a pillar is just a little too far forward to the front of the car.
I always took metal off from the new parts rather than the original metal, unless it's rotten of course. Too late now but a useful tip I used was to prop the door ends under a jack stand to help stabilise it while I located the bolts. No clue why you cut so much of the wheel well away.
Perhaps some has mentoned this before, and I do not want to back seat drive your repairs, but may I make a suggestion. Your Pillar welds are butted and welded with a Mig. When you do this and the grind the welds flat, you have removed most if not all the weld, you lose the strength at the seam. There are 2 ways to avoid this, one would be to weld a backer plate behind the pillar and plug weld this plate on each piece. The other is to leave a gap between the two parts you are welding , typically the thickness of the metal you are welding. This allows the weld to fill the gap and keep the strength once the panels are ground. i
Every mistake can be thought of as a learning experience... especially if all it takes is bit more work to remedy. It's too bad about that door though, but I have a feeling you'll find a way to get the original to work.
Good Job Fixing the problem!
As someone who has done VW beetle restoration, I made a template with door hinges which I bolted in place before welding the pieces back in and that made sure the door fitted, good job you learning as I did along the way!
Wow!! Good idea!!
Yes, that's a great idea..
This video gives me hope. I have 6 beetles. I used to think 2 were beyond repair. This was enjoyable, thank you.
Man your videos are literally treasure. Visualisation of the process makes a huge difference when one's going for such an endeavour! Thank you for the knowledge man!
Thanks man! I try to capture as much as possible. I hope it helps! =)
@@CTmoog It does, looking forward to seeing your bug complete!
Learning more each episode I watch
Hate to be an armchair coach so I appoligize for doing it. Before taking anything apart put your bracing in the interior to stabilize the body and leave it in place until all work is done. Any work around doors do it with the door in place, thats what you did on the drivers side. When parts are tacked in then remove the door. Excellent frame of mind CT you are moving ahead in leaps and bounds. Cheers.
That's what I thought as well. I can't lie CT is really doing well for a beginner. Definitely better than me.
What type of welding do you recommend? MIG or TIG
It’s armchair quarterback. But..just an observation. Carry on😆
@@novavolks9652 I use gas for pannels and mig for structural. Have not tried tig yet. I like gas for cut and but because it leaves the metal pliable, tig should as well.
@@jimsmitn7569 Never did play football, in our day girls didn't so glad times have changed.
Have now watched every episode up to this one. I greatly admire your steady progress. Speach is clear and concise, just at the right speed.🎉 i recently compleated my restoration of a Morris minor convertible, and I had the same problems that you are finding. It's an enormous learning curve, and it took 2 years. Did part-time courses at the local tec, to learn techniques, well worth the time spent. 🎉🎉🎉 i had to buy very thin shims to get door adjustments, correct.
The best part of doing restoration is learning how to do it. It’s difficult. That’s why we do it
To conquer the challenges. Well done CT !
Thanks Ed! =)
We all have fun days like this.
Watch out with rear quarter panel patch i had trouble fitting up the running boards. But we all live and learn. Nothing ventured nothing gained. Measure twice cut once.
Enjoying watching your chanel
Thanks.
"TEXAS", you getting some time /hands on experience but keep it real you got less than 40 hours welding...fearless keeps welding...tanks for sharing
Thank you! =)
always remember to measure twice and cut once, a next thing when you offer up the doors make sure the car is sitting on its own weight and not being jacked up that will throw the measurements off when you cut and paste...love the channel keep it up.
^^^^ This. Measure, measure, measure and make notes. And use a straight edge where you can on flat surfaces such as the vertical hinge panel to keep the panels straight. True, you do not jack up a corner of the car to help aligning and welding in panels. It needs to be sitting level on all fours to get an accurate fit with the body shell at rest. Welding in the hinge panel on the left side with the floor jacked up most likely lead to the door being too low once the jack was removed. Just helpful tips here.
Really enjoy this rebuild series I have been scared to buy a bug with rust but watch you I believe I can do it your not rhe only one learning from your mistakes
Wow... you live and learn. I've jacked that up ONCE. Then I got someone smarter than me to do it. Good work trying to fix your mistake.
I admire your patience.
best vidio so far it shows when things dont co right firdt time !
I have to say CT that looking back to when I first started looking at your videos, the 1962 VW van (Rusty?),you have made SUPERB progress and your skill now is beyond what most DIY car owners possess. Well done young feller, thanks for sharing and best regards from Ireland.
Repairing the original door is another challenge. But in my opinion it would be right decision Great work man, keep it up!
Thanks Van!
Well done for your persistence, I suppose that is what real life is about. We are faced with so many challenges in life. But we need to be persistent and not to give up. Life is not easy but we need to make it work.......
nothing better then a nice new paint job on a old Beetle to look sweet , new paint
Looking great brother.
love the way you have grown with time,great work
Messing up is part of the learning process. I am working on installing a fuel level sender and fuel gauge in my '59 bug and I ruined the 1st tank. I drilled the hole in the shallow part of the tank and now the sender doesn't fit. I'm not sour about it but it was all due to doing things the lazy way. Oh well. I'm already on my second tank. Waiting for the self drilling screws. Best of luck. I love these videos.
Thank you! =)
I really like watching your videos. you are very persistent. is doing a great job. congratulations
Greatly admire your work and persistence. This is my favourite vehicle project on YT.
Thank you very much! =)
For all the amount of metal work you’ve done, I think you’re doing great! I’m amazed how the doors seems to close well, and that’s without even finishing the whole metal work on the back portion of the car!👌😎👍
Thanks for your video, as I have seen other sites that are perfect, not realistic, would rather watch the mistakes, the process, and still getting job done we all. make mistakes.
Thanks George!
Well done CT excellent recovery. Looking forward to more Videos. One can tell by the sounds from the doors closing the project sounds VW.
It takes a team to do it right. We are all in this together. I have been working on a type 181 for almost eight years so close. With very little help. Go for it CT ! Learn as we all do.
Keep going CT you got this !!
Great job on pushing through and adapting to the situation of the metal work! Love seeing u dig in and get it done. Can’t wait to see the Porsche get done as well. Enjoy your thanksgiving!
Mate. You are inspiring me to start my 57 build … love your patience and how you recovered ..
Thanks Chris! You can do it! =)
@@CTmoog love to chat with you one day. I’m setting up my garage at home now. I’ll send you a couple of photos of what I’m starting with.
Great to see again. I'd be tempted to repair the base of the original door for the better fit. Good luck with it whatever you do!
Nagyon jó vagy barátom!
I watch so much car content on RUclips where the only issues that rise up seem to be manufactured. I could feel your frustration after fitting the door the second time and still not being successful. Like most of us even remotely brave enough to try this as amatures would. You are way better than me but you give me hope that my skills will eventually get me to where I need to be.
CT, what I find interesting about your channel is that it’s not an “instruction”. But rather an “adventure”. Would hardly be the same if you were an expert. You pay the rent, buy the cars, the tools and share the struggle! I look forward to many more rough rides….
Yep, it is nice to see other DIY people figuring things out and making mistakes (and fixing them). CT is very humble.
Great work just keep moving forward you will get there eventually
Congrats for sharing with us candid learning process. If I were there, I’d suggest: keep a welded bar holding body wide near B column; use the jack to hold/lift the door to screw/adjust; use vise grips holding new insert to car, chek exact position several times and cut simultaneously new and old part in a single cut. Remove excess and weld definitive and precisely at the single cut. Advising is easy…make it happen is for the heroes! Best regards from Brazil.
friend now if this side gave you a lot of work, I think it is better to repair the lower part of that door, and so this project continues with most of its original parts, dude, you have already come a long way with this project and you are excellently very advance, have a little faith in how you are doing it, and don't let rust win you over. big hug from the southeast of Mexico. Blessings.
wow, maybe this is why my 62 fought me, I had a different p side door, damn.... I feel this helps me be better prepared when I get to my 65.
This is fantastic, sir! You are turning into an expert right before our very eyes. You are taking the time to measure and are doing excellent work. The content of your videos has improved EXPONENTIALLY since you started really getting into it. You have a great attitude that will prove invaluable and you’ll gain the confidence to tackle more and more complex projects.
Re the alignment of the passenger door; remember you are still missing the metal panel inside the wheel well that will reinforce the area.
😂 From Svizerland 🇨🇭 you are a welding artist, well don, i have enjoi the chassis monting becose i never see, you also well don this, thanks
I like it when somebody is willing to show the mistakes right in the video because that's exactly what I'd be up against if it were me. Would have been so easy to cut to a polished repair and keep moving like crap like that don't happen.
Le está quedando biensísimo su RECONSTRUCCIÓN DE SU AÑORADO "VOCHO" SE NOTA QUE LO ESTÁ HACIENDO CON EMPEÑO, MUCHO SACRIFICIO Y SOBRE TODO CON AMOR ¡BUENA SUERTE
I hate it when I try to put the horse before the cart, drives me nuts, and all because I was thinking 4 steps ahead before making sure what I was doing was right. But that's how you learn, by making your own mistakes the having to fix them. Nice job in the end you got where it was supposed to be, and that's all that counts!!
I would have dropped at least one screw into the a-pillar! Use pieces of the donor door to patch up the bottom of the original door and keep that awesome patina! Great watching as always! Keep up the good work and attitude!
Good video! Good on you for showing your journey on this - "metal is clay" add to that "measure twice, cut once" ;-)
Keep your original doors and fix them up - you have the skills, you can do it 🤜
Parabens Muito bom, gosto muito de acompanhar a Restauraçao do Fusca (Beetle).👏👏
Amazing work! I could only wish that I could do such an awesome job! 👍👍🎉🎉🎉🎉🎉🤘🏻🤘🏻 Thanks for showing your mistakes as well and not editing them out.
Thank you so much 😀
Excellent Job! CJ
Thanks Sam!
It’s looking good 😊👍
Hi My Dear Friend Very Very Good Job ❤❤❤❤❤
Tenho um VW 74. Gostaria de ter sua coragem de colocar a mão na massa como o senhor. Admiro sua persistência para fazer este trabalho só e ainda nos proporcionar este aprendizado e divertimento. Parabéns e obrigado.
Awesome Video CT
Nice job I see that this side was a bit more difficult take your time buddy it will come out good 👍🏻👍🏻👍🏻👍🏻
This one was a doozy. Keep up the good work!! 👍
Wow! I appreciate to watch your efforts. 😅😊
ct when you do those repairs use part of the old pillar to sleeve inside trim the edges till it slides inside then tack weld it to hold it it will make it a stronger repair rather than butt weld as they tend to crack in areas like that under stress
because you had nothing attached to the heater channel it allowed it to move up on you first attempt
Good job and good video.
Congrats: All the sh't happens - und CT is staying in rather fine mood. My own patience would not be enough for such incidents 😭... Keep welding and have a good success and make the whole project perfect sooner or later
Thanks may friend! =)
It’s a great attitude and he’s doing a beautiful job. He’s turning into an expert right before our eyes and it’s a great thing to see.
Way to persevere! Maybe trying to fix the rusted-out original door is worth pondering? I don't know, just a thought.
Thank you! Yes, I'm going to try and save the original door.
Mate I told you when you did other side use your trolly jack to hold your door up instead of struggling to hold door and try to fit a screw its not hard work smart not hard you will get it and try practicing on your bench to tack two peices of metal play with setting wire speed and heat you will get there great video 👍👍
I'm watching this for the first time!!
Excelentes videos ,pero ojalá hubiera más avance ,,saludos desde Monterrey,México , excelente trabajo
Many people like to talk about the 1967 as a one year car, but nearly every year of Beetle was a one year car. VW made incremental improvements of the Beetle every year, some years the differences are obvious like the 1967 some years are more subtle, then you have the half year improvements, where they added a feature for 1965 near the end of the 1964 model run. So, that door could be a 65, or not depending whether VW was introducing an improvement.
Good point!
You should of removed the brace and placed it higher between the middle pillar and the door pillar otherwise your geometry 📐 will be out. (So you’ve gathered) 😂
Also whenever you are replacing a rusty part. Place the new panel over the top using vice grips or clamps then cut once. You’ll then have the perfect cut for the replacement panel. The door pillar is a structural area so you should use a piece of the old panel behind the new and old to bond them together thus making that area stronger.
I hope you listen to everybody’s advice and continue to make this build great 👍🏻
i love these metal work !
Finally you got a good results
Mistakes are when you actually learn something, I always get worried when stuff goes to well..live real.
I did exactly the same thing and forgot to put the door on but luckily it fit
My vote is repair the OG door and keep most of the patina, they sell lower outer door skin and the inner structural piece as well.
Thanks Mike! I might do that.
I’m really worried, REALLY worried, that you’re going to think that A pillar is good to go. My friend, it is not.
That is a structural connection, and the critical interface is a series of butt-welds that can’t be sound enough to keep the car together.
Someone else has mentioned using stiffeners. Doublers, stiffeners, back-side patches…whatever you call it, it needs to be used to ensure your Bug will hold together. Please weld in additional plates to make that A pillar stronger than original.
That's a great idea Bill. I will do that today.
@@CTmoog thank you!!! I really enjoy watching you learn as you go! I was truly worried, though, that you’d made a decision that might’ve put your butt in danger my friend.
Can I also suggest you gets some 20 or 30 thousandths skin and practice your butt welds. Please keep in mind that just because you can buttweld skins together, you can’t necessarily return a patched area to the rigidity and strength of the original formed, solid areas like the A pillar foot on the tunnel. Stay patient, my friend!
This is the best comment ever. I don't know anything about restoration, but when I saw that the welds (in one case two slightly separated) on the structural post without any reinforcement I thought that I don't buy or drive this car... :9 I said it with a better vibe ;), bro !!!!
Admire the work that you're doing, but this comment is dead right. The A Post is a vital structural component in the event of a collision and any reduction in its integrity could make the difference between surviving or not.
Why don't you cut the good part off the new door and stitch it to the bottom of the original door like a repair panel? You would have the same good fit and most of the patina that way.
The old saying, "measure twice and cut once" comes to mind.
In my opinion, it would be nice to have the original passenger door in place. It is a hard task to save it, but the original rusted paint would give it an excellent look and feel, and this door is the original. Every beetle likes its original parts. :) And after the restoration of the body there would not have to paint.
Ffggcc
Hey mate. It really looks like the best thing to do would be to just cut the bottom 6 inches off both doors and swap them over. Then all you'd have to do would be to blend the paint on the bottom bit so it wasn't red. It would be so great to keep the matching patina of the old door, wouldn't it? By the way I'm loving your vids - the way you face a mistake with a sigh and a laugh, then just carry on is really great. Many weaker men (like me) would've kicked the welder across the garage and gone for a pint. Well done mate, keep it up, we're all with you.
Show , que serviço top. 🇧🇷🇧🇷🇧🇷🇧🇷
Aew outro br
Can you somehow repair and use the original door. That original patina?
I think we can! I will keep you updated.
Ola amigo funileiro ja sofri muito tambem trocando pé de coluna parabens pelo canal sucesso um forte abraço aqui do Brazil
Hi CT, greatings from 🇵🇹 Portugal. Fix the botom of the original door abd will be fine...kip the god job. Saúde
Thank you my friend! =)
You need to remove those welds at the bottom of the post and move it to the back of the car, that way it will lift the back of the door...
One should think that messuring the correct distance between the A and B post would be the first thing to figure out..
@@Mr.-Wint But most don't lol.
Years ago I had a boss that told me "If you're not making mistakes, you're not working hard enough!" Darned if he wasn't right. LOL
They do sell replacement panels for the bottom of the doors. Like the whole section, so maybe it's worth a shot to try and fix them.
Sometimes it just does not go easy.
Que legal amigo parabens adorei o trabalho. tenho um fuscao 79 prescisando de uma boa reforma no assoalho e na porta,.sucesso
Any particular reason you choose to Tack your welds instead of following a consistent weld?
At that point another new part would have been the best. Putting the whole door, shimming it and tack pointing the part, somehow, somewhere. You could even brace the new part to whatever accesible and weldable section of the body. But as you said, it's a learning process. Hard to be in your shoes.
Somebody's having a bad day....somedays ya just gotta take a break and have a few 🍻
So long as you are learning good luck
Great job 👍👍👍👍
Keep on keeping on son learning by mistakes...
Could you fix the original door? I know you can get door bottom panels.
That was a tough one to deal with!
I think you will need to cut the bottom of the a pillar back off and put a jack under the door then tack it in the a pillar is just a little too far forward to the front of the car.
I always took metal off from the new parts rather than the original metal, unless it's rotten of course. Too late now but a useful tip I used was to prop the door ends under a jack stand to help stabilise it while I located the bolts. No clue why you cut so much of the wheel well away.
37:43
Yeah. Try thread rolling, pal.
(Kidding. Loving the videos. Keep it up!)
Was so relieved when you put the original door back on. Should always fit to the original if possible. Then make the door fit the chassis
Perhaps some has mentoned this before, and I do not want to back seat drive your repairs, but may I make a suggestion. Your Pillar welds are butted and welded with a Mig. When you do this and the grind the welds flat, you have removed most if not all the weld, you lose the strength at the seam. There are 2 ways to avoid this, one would be to weld a backer plate behind the pillar and plug weld this plate on each piece. The other is to leave a gap between the two parts you are welding , typically the thickness of the metal you are welding. This allows the weld to fill the gap and keep the strength once the panels are ground. i
Hi can you tell me when you do that pillar do you bolt the body to the chassis. I have not weled the heater channel to the body yet.
Every mistake can be thought of as a learning experience... especially if all it takes is bit more work to remedy. It's too bad about that door though, but I have a feeling you'll find a way to get the original to work.
Good job 😉