Dear good sir. Thanks for the video, it's really nice. I ordered the exact same parts as shown in the video but i have one question: is the extra fuse necessary? If yes, are 10A enough? Or should i rather use 16A (I'm from Germany and we have 230V and up to 16A from the wall). I think there is a fuse on the dc2412, but not sure. Thanks!
Great project!. What's the maximum power you can draw from it? Also, two suggestions. 1) You can use a multiturn potentiometer for accurate and fine adjusting. 2) And adding a 24v cooling fan will make the project even better.
@@Comrade_YG Noctua fans are pretty quiet. I use them on my 3d printer. Factory fans would run you out of the room, hardly hear the Noctua fans running.
I dont mean to be so off topic but does anybody know of a trick to get back into an Instagram account?? I was dumb lost my account password. I would love any help you can offer me.
@Aries Sterling thanks for your reply. I got to the site thru google and I'm waiting for the hacking stuff atm. Takes quite some time so I will get back to you later when my account password hopefully is recovered.
Your welcome.. I think you can but it is not recommendable since you might over voltage it. It is better to use a similar battery when powering devices like laptop and phones
can i use 12v as input supply? i have 12v switching supply. Also, can I connect two buck convertor to single power supply as to get a dual output supply
a 12-0-12 should give you 24 volts ac, run that through a bridge rectifier with a capacitor and that is 24x1.4= 33.3 volts dc. the limit of the XL4016 is 36 volts so you should be ok.
I used transformer 9 0 9 5408 diode in my xl4015 module. Now it shows 23 volts but after loading it becomes 9 volts, why is this happening? And what to do.
hello sir I have a 12v 30A smps i want to make a adjustable power supply 2v-30v, i have two different options with two module 1: use 150w step up dc converter for reach 30v and then use 300w step-down dc converter for adjust voltage. 2: use both modules separately, it's mean 150w step-up dc converter for above 12v range and 300w step-down dc converter for below 12v range which on is better or maybe both are bad idea?
I actually use the first method. In case you need more power, combine 2 150w boosters in order to match your buck converter. The second method seems to be inconvenient (in my taste)
I was having an idea that smd rework station has an adjusting knob for fan and temp control It delivers voltage upto 24 v Why can't we use it to make variable bench power supply If you can make one It is a totally different project no one has ever done
@@VINInvents That's good. I'm also upgrading my old power supply, an LM317 with a 2n3055 booster. But I will be using the XL4016E1, XH-M401. The one with the potentiometer included.
@M.D. Suave: The LM2596 has a DC input range of 3,2V to 35V. This can be used to install any other component with a much lower voltage. Like for example, a 12v fan for extra cooling.
Can I solder a normal 100 kOhm resistor to a 100 kOhm multiturn potentiometer in order to get to 200 kOhm? Can't find a 200 kOhm multiturn potentiometer! My step up booster uses the 3296-1-204w trimmpot
@@VINInvents I know. But I have to use a 200k ohm potentiometer as a replacement. I would like to use a multiturn potentiometer but can't find one with 200k ohm only with 100k ohm.
@@GreenFart174 ohh okay well I haven't tested if its possible and I dont have multiturn potentiometer.. You can test it for yourself if you want and update me
May load po ba ? Sadya po nagalaw yung amp basta may load.. example po 5v tas nag lagay ka po ng dc motor gagalaw yung amp kunware 0.3amps tas ibig sabihin po ay max ng dc motor sa 5v ay 0.3 amps. Pag tinaasan nyo naman po kunware ng 12v mag aadjust din po ang amp kasi mas lumaki po yung current ng electricity. Pag binabaan nyo naman po yung amps mag aadjust din yung depende sa load. Tas kahit po naka max yung potentiometer tas maliit lang ang load mababa lang po yung current kasi yun lang ang kailangan ng load
@@kerbyarcigalretuta6820 Po, eshte normale. Edhe une kam perdorur ushqyesin e laptopit dhe skema punon shume mire duke rregulluar tensionin dhe rrymen deri ne 4,1 A.
This is a good lab bench power supply but I have to tell you that you can't use it as very good lab bench power supply as the voltage increases very fast.
@@mohitsolanki2426: So was i. I built one with the exact components and used the 10k 3590S-2 103L precision multi-turn potentiometers I mentioned in my previous comment. And i use it every single day as a lab bench power supply.
The datasheet of xl4016 says it's capacity is 8 Ampere and recommended load is upto 5 Amperes. So , how much max load current can actually be drawn and will it be used with the heatsink that's already fixed on this board or extra large heatsink or cooling fan needed if we draw upto 3 Ampere or even 5 Amperes ?
Can you make it and send it to me please how much is totally with courier charges I will pay you please let me know and send me the price of power supply please
![Twenty One Pilots - “The Line” (from Arcane Season 2) [Official Music Video]](http://i.ytimg.com/vi/E2Rj2gQAyPA/mqdefault.jpg)
I from Indonesian, and i see you video, wow amazing. I make psu from you. Thanks you big thanks 🤩
Thanks for this....was thinking one buying one but I’ll have a go at building this instead .
nice project, congratulations. If you have made a wiring diagram, can you publish it? Thank you
Suggested Videos For you
Liitokala Unboxing
ruclips.net/video/AOLAVMc99vI/видео.html
DIY 12V Power Supply
ruclips.net/video/vrW7OloAl4U/видео.html
DIY Variable Power Supply
ruclips.net/video/uOqX66ftU6k/видео.html
Follow Our Facebook Page!
facebook.com/A.VElectroDIY
Ficou TOP demais, só faltou uma ventoinha puxando o ar para fora.
You're doing great men, Keep it up! Cheers!
Thank you : )
Good project. Whish you used a cooling fan. it would be better. Thnks.
Thank you bro, since buck converter are costly I am also thinking of same technique but I don't weather it's works or not thanks for this video
Does this module contain overcurrent led indicator???
@@nagaveninagu978 no. LM2596 will burn
@@nagaveninagu978 Yep!
Dear good sir. Thanks for the video, it's really nice. I ordered the exact same parts as shown in the video but i have one question: is the extra fuse necessary? If yes, are 10A enough? Or should i rather use 16A (I'm from Germany and we have 230V and up to 16A from the wall).
I think there is a fuse on the dc2412, but not sure.
Thanks!
It's to protect your Module, 5a or 7.5 is enough. Thought the fuse is not necessary.
@@VINInvents thank you for the reply. I will take it into consideration!
Which diameter did you use for the AC Wires?
Very good sir g
Nice video,,Neat work I like
Very Good...!!!
Thank you for your video. My potansiometers’ reaction time is 2 seconds. I turn the button but it reacts in 2 seconds. What is the problem?
Your welcome, your reading is delayed? Try changing your voltmeter
@@VINInvents yes my voltage reading is delayed. I turn the potansiometer but I can read the voltage after 2 seconds. Your reading in this video is ok.
Try putting 10k ohm resistor on the buck
NAKO MAPAPA ORDER TALAGA AKO NETO SA SHOPEE😅😅
Hahaha order na sir
hola.seria bueno colocarle a la salida algun filtro pi, las suichadas son ruidosas.
Great project!. What's the maximum power you can draw from it? Also, two suggestions.
1) You can use a multiturn potentiometer for accurate and fine adjusting.
2) And adding a 24v cooling fan will make the project even better.
And the fan will also make it noisier
@@Comrade_YG There are noiseless fans out there. So the modules won't fry off.
@@Comrade_YG Noctua fans are pretty quiet. I use them on my 3d printer. Factory fans would run you out of the room, hardly hear the Noctua fans running.
dose it have any protection for shortcut az high current make dc to dc modular burn
I tried maxing voltage and current and short the output, the wire instantly heat up
You can modify directly your SMPS power supply to get variable voltage, just replace resistor with variable transistor.no need buck converter.
Yes I know, like I mentioned in the vid its for looks
What is the max voltage and current on this power supply?
Thank you and keep up the good work.
24v 10a
I dont mean to be so off topic but does anybody know of a trick to get back into an Instagram account??
I was dumb lost my account password. I would love any help you can offer me.
@Aries Sterling thanks for your reply. I got to the site thru google and I'm waiting for the hacking stuff atm.
Takes quite some time so I will get back to you later when my account password hopefully is recovered.
@Aries Sterling it worked and I actually got access to my account again. Im so happy!
Thank you so much, you saved my ass !
@Justice Nasir happy to help xD
nice work man
Good day sir, i wondering what cable sizing that you use from 3 pin power cord to ac-dc module and from ac-dc module to xl4016 module.. Thanks !
I think its Size 18 Automative Wire if I remember correctly
Can i use 250k potentiometer or 500k??? Also nice video i did all you did but i only have 250k and 500k left. Thanks
Does this module contain overcurrent led indicator??? If not how do we know current drawn is exceeding the limit???
Im not sure sir.. but the led turn red when the output got short
Good job.
Appreciable.
Please provide diagram with components detail.
Watch the whole video without skipping you will see the schematic diagram
very nice. thank you for sharing.
is it good to use it for injecting a voltage to mainboard laptop?
Your welcome.. I think you can but it is not recommendable since you might over voltage it. It is better to use a similar battery when powering devices like laptop and phones
Instead of using the 24v switching power supply that you used, can I use a laptop charger, even if it is not of the same amperage or voltage?
Yes, but it will have lower voltage and ampere
Po, une kam perdorur nje ushqyes laptopi me U = 19,5 V dhe rryme 4,1 A , skema punon shume mire dhe nuk ka nevoje per vetilator ( ftohes )
Super...
can i use 12v as input supply? i have 12v switching supply. Also, can I connect two buck convertor to single power supply as to get a dual output supply
Yes you can
@@VINInvents what is the use of 2596 module in this circuit?
How many Ampere can it draw
nice work
Dear i want to buy this. Plz help me
Sir can we use a 12-0-12 5 amp transformer with a bridge rectifier for input
Im not sure.. you can try it, also wouldn't be the max voltage will only be 12 volts?
@@VINInvents but sir we can take 24volts from a 12-0-12 transformer
@@virendrasinhpatil6883 oh okay.. sorry
@@VINInvents 👍👍
a 12-0-12 should give you 24 volts ac, run that through a bridge rectifier with a capacitor and that is 24x1.4= 33.3 volts dc. the limit of the XL4016 is 36 volts so you should be ok.
Great job! Congratulation.
Thank you : )
excelente video
I used transformer 9 0 9 5408 diode in my xl4015 module. Now it shows 23 volts but after loading it becomes 9 volts, why is this happening? And what to do.
Why did you adjust spep dawn to 12v, why?
Because I like it that way, its optional if you don't want it then don't put it
এই পাওয়ার সাপ্লাই দিয়ে কি মোবাইলে সার্ভিসের কাজ করা যাবে
hello sir I have a 12v 30A smps i want to make a adjustable power supply 2v-30v, i have two different options with two module
1: use 150w step up dc converter for reach 30v and then use 300w step-down dc converter for adjust voltage.
2: use both modules separately, it's mean 150w step-up dc converter for above 12v range and 300w step-down dc converter for below 12v range
which on is better or maybe both are bad idea?
I actually use the first method. In case you need more power, combine 2 150w boosters in order to match your buck converter. The second method seems to be inconvenient (in my taste)
Esas cajas donde se consiguen
Donde puedo comprar la caja
I was having an idea that smd rework station has an adjusting knob for fan and temp control
It delivers voltage upto 24 v
Why can't we use it to make variable bench power supply
If you can make one
It is a totally different project no one has ever done
If you install one cooling fan, it would be better. 👍👍
Thanks for the advice
good
Thank you😁
Why the small 12 volt buck converter, why do you need it?
I already explained why I added a step down converter before in the comment section
We can charge 150ah battery with these ?
Did you feed the panel voltmeter with 12v?
thank you
Leptop charger is good for start 🙋♂️
I think the use of the LM2596 is not needed. The led voltmeter/ammeter working voltage is up to 30v and your power supply is only 24v.
I want it to have a lower voltage. And its also for aesthetic : )
@@VINInvents That's good. I'm also upgrading my old power supply, an LM317 with a 2n3055 booster. But I will be using the XL4016E1, XH-M401. The one with the potentiometer included.
Good Luck : )
@M.D. Suave: The LM2596 has a DC input range of 3,2V to 35V. This can be used to install any other component with a much lower voltage. Like for example, a 12v fan for extra cooling.
Yes : )
Can we run car stereo with this
If the stereo is 12v then its possible
What's the Ampere of main smps of 24 volt?
What is the use of left and right knob?
Right for the voltage
Left for the Current
What happen if you touch the red wire and black wire..it will cut off the current and voltage like real power supply
Nope.. the wire will instantly heat up.. I tried it with the voltage and current at max
@@VINInvents thanks boss
Good day sir where from I will get this kit kindly send link
E' possibile avere il link, per trovare il contenitore di questo alimentatore in commercio? Grazie per un eventuale risposta!
Bro can we used it for mobile repair
Will it work with 100k potentiometer ......Plz reply
Im nott sure since I haven't tested it yet
Great project.
What are the dimensions of the enclosure? Did you order it online?
Cheers.....
Thank you for enjoying my video.. The box dimension is approximately 20x14x9.5cm.. I order it from shopee and its currently out of stock
It is better if a cooling fan is fixed inside the unit.
Why did you use just 2 legs of trimpot instead of 3 ? ( yellow and green wire ) You didnt use third leg.
Can I solder a normal 100 kOhm resistor to a 100 kOhm multiturn potentiometer in order to get to 200 kOhm? Can't find a 200 kOhm multiturn potentiometer! My step up booster uses the 3296-1-204w trimmpot
What do you mean 200k ohm? On the vid I use a 10k ohm
@@VINInvents I know. But I have to use a 200k ohm potentiometer as a replacement. I would like to use a multiturn potentiometer but can't find one with 200k ohm only with 100k ohm.
@@GreenFart174 ohh okay well I haven't tested if its possible and I dont have multiturn potentiometer.. You can test it for yourself if you want and update me
@@VINInvents This will take a while. Buy it from china and i live in germany.
Found a temporary solution.
ruclips.net/video/9VJiTVfV5nU/видео.html
Where are you from?
I'm from Malaysia
Philippines
@@VINInvents ok thanks for reply
@@adaanishhh you are welcome
What is the power rating of your XL4016?
Its power rating is 300w (max @30v and 10a)
ये पावर सप्लाई कितने मैं बन गई है बताएं
What size is the box?
Can the potensio be a multi turn?
Yes
Fuse rating amps please?
1.5amps
Hey guys this person has used lot of modules so if you have 12 0 12 transformer you can use instead od the second module
Diagram?
you dont need diagram if you folow the video step by step
good day sir newbee po ask lang po bakit po yung buck converter ko tumataas amp kahit naka zero potentiomer
May load po ba ?
Sadya po nagalaw yung amp basta may load.. example po 5v tas nag lagay ka po ng dc motor gagalaw yung amp kunware 0.3amps tas ibig sabihin po ay max ng dc motor sa 5v ay 0.3 amps. Pag tinaasan nyo naman po kunware ng 12v mag aadjust din po ang amp kasi mas lumaki po yung current ng electricity.
Pag binabaan nyo naman po yung amps mag aadjust din yung depende sa load.
Tas kahit po naka max yung potentiometer tas maliit lang ang load mababa lang po yung current kasi yun lang ang kailangan ng load
Hindi din po ako 100% sure since di naman po ako expert
@@VINInvents opo sir pag my load bigla nalang tumataas amp .ok nman voltage nya.
Sir if sa laptop gagamitin ang 19.5v possible din ba maiadjust yung amp? Balak ko sana gamitin for laptop repair. Adjustable din ba ang ampere?
@@kerbyarcigalretuta6820 Po, eshte normale. Edhe une kam perdorur ushqyesin e laptopit dhe skema punon shume mire duke rregulluar tensionin dhe rrymen deri ne 4,1 A.
This is a good lab bench power supply but I have to tell you that you can't use it as very good lab bench power supply as the voltage increases very fast.
Yes. Thank you 😊
@Mohit Solanki: Actually, you can. Simply replace the 10k linear pots with, for example, 10k 3590S-2 103L precision multi-turn potentiometers.
Yes. Im planning to use it for future projects
@@johnmacedo4483 I know, but I was talking about VIN Invents.
@@mohitsolanki2426: So was i. I built one with the exact components and used the 10k 3590S-2 103L precision multi-turn potentiometers I mentioned in my previous comment. And i use it every single day as a lab bench power supply.
The datasheet of xl4016 says it's capacity is 8 Ampere and recommended load is upto 5 Amperes. So , how much max load current can actually be drawn and will it be used with the heatsink that's already fixed on this board or extra large heatsink or cooling fan needed if we draw upto 3 Ampere or even 5 Amperes ?
Input amp
Use fan
Cas aki apa bisa🙏🙏🙏🙏
provide schematics !?
Can you make it and send it to me please how much is totally with courier charges I will pay you please let me know and send me the price of power supply please
40 V in max in ok for me and out is 32v max start whit 1.5 v
Bench PS? On switching technology?! Definitely the worst engineering solution.
Tarnlas sinhala
아저씨 납 별로 안좋은 걸 쓰네.
you dont want it to be soldered?