DIY Lab Bench Power Supply | Adjustable Power Supply
HTML-код
- Опубликовано: 8 май 2019
- Hello! in this video you will see how to make adjustable Lab Bench Power Supply from computer atx, if after watching you have questions, ask them in the comments, enjoy your viewing
Digital Voltmeter Ammeter lite.bz/niWln
4 Bit Digital Voltmeter Ammeter lite.al/5ovRZo
power switch ali.ski/pvOH2Y
DC DC Converter ali.ski/R_sU7
Powerful DC DC Converter lite.bz/DI7mM
Potentiometer ali.ski/vvpGO
Better Potentiometer lite.al/qdK0VL
Much Better Potentiometer lite.al/SYiMS
Ring Connector ali.ski/ArUot
Drill Bit ali.ski/nF9jxq
Center Drill Bit ali.ski/m0VEg
Banana Connectors ali.ski/4YdlJ
alligator clip ali.ski/myhpj
Potentiometer Plastic Knob ali.ski/vBNoO4
3D Carbon Fiber Vinyl ali.ski/cHyHUy
Connector Terminal Banana ali.ski/AEtk2o
Heatshrink Tube ali.ski/ae5fhl
Wire Stripper ali.ski/9HpB6B
rubber feet lite.al/93lh5
Self Adhesive Rubber Feet ali.ski/gPzJy
Solder Wire ali.ski/Ip2Dud
Wire Cable Cutters ali.ski/h8n3QT
electronic caliper ali.ski/t1-I-
Heat-resistant Soldering Mat ali.ski/BClz_E
🔔Subscribe to the channel: / @crafttime3360
Music
Itro & Tobu - Cloud 9 [NCS Release]
NCS Spotify: spoti.fi/NCS
Free Download / Stream: ncs.io/cloud9
Tobu - Infectious [NCS Release]
NCS Spotify: spoti.fi/NCS
Free Download / Stream: ncs.io/infectious
Elektronomia - Limitless [NCS Release]
NCS Spotify: spoti.fi/NCS
Free Download / Stream: ncs.io/Elimitless 
Наука
Great video! When marking where you are going to cut, you might want to use a lighter tipped pen.
Are you supplying voltage to the display via 5Vsb?
Bellissimo lavoro complimenti
Great job, thanks for sharing.
For us mechanics, would you happen to have a schematic for this build? Thank you.
Good work
it's so good 👍👍👍
Great job and craftsmanship.
What voltage and amperage values can you achieve with this power supply?
Best regards
12 volt power supply and 5 amp converter, but you can put a more powerful module
Hello can i do this with out a dc converter?
exelente trabajo
agradecer
if we make a short circuit on the ATX power supply it automatically stops working My question is, if we make a short circuit at the output of the inverter or will the power supply stop working too?
So I need to supply 7-28V @ 25-30amps...what parts would I need ?
Thank you
i need the picture diagram of hookup of the pots to the board where the pot wires go to the board. i have lost it thks
Can you posible to unform what is ampior in this dc power supply
buenos tardes amigo una pregunta
este sirve si o no para fuente de laboratorio para celulares
Parabéns pelo projeto!
Poderia demonstrar o esquema de ligações dos potenciômetros no circuito dc-dc, não ficou muito claro no vídeo.
Obrigado por compartilhar esse conteúdo de qualidade.
He replaced Potentiometer instead of multiturn on this Dc to Dc converter module.
Both of them has 3 legs.
Leg 1 and 3 is fixed resistor and 2 is variable rather those legs.
Leg 1 and 3 can be in left or right side position but 2 is in middle therfore dont worry about connecting it to the module in any direction. (Just pin 2 should be in middle.)
I am sorry cause of bad English.
@@geopeliaaow3768 obrigado pela resposta!
Continuo seguindo seu canal. 🇧🇷
Super genial
Hello.
Perfect.
What is the highest output voltage of this project?
Hello very helpfull video tutorial,may i know second tuning its for current ampere?
Hello, yes
Hello, we have an agricultural land that has no electricity. Now, if we want to use a motorcycle battery, which is 12 volts, to get different currents, such as 10 or 12 amps, what transistor should we use?
Nice
What is the specification of the DC-DC converter that you used?
Tnx for shearing a great project. But it will be better if u use + 12v & -12v for input of ur dc dc converter. Then u get 24 v. I recently made one using xl 4015 converter
thanks, I thought about it, next time I will do this
but the amperage output is minimal for 24V, about 300mA.
I also have a xl4015 module, but can you tell me how to get 24v out of an ATX supply without losing ground?
@sazzad hossain I also have a xl4015 module, but can you tell me how to get 24v out of an ATX supply without losing ground?
@@AndrewAnno connect yellow wire in xl 4015 converter (+ve ) input & purple wire in (-ve) terminal
can you use the same components for a 300 watt comp sup
yes
Is it XL4016 buck converter module?
Привет,а схема подключения есть?
i followed this tutorial and now the power supply is not working (when i connect the green wire to the ground, it turns on and after half a second it turn off again), i used a new power supply that was totally functional before. Does anyone knows a solution for this?
Good tiching karte hai 👍👌👍👍👌👌👍👍👌👌👍❌
i think it's better using step up down module
Why would you need to short the data pins on the USB plug?
Apple products won't charge unless data pins are shorted.
@@byrondallas4676 only for apple... And what about android?
Nice video but most of us will not be able to make this because there are no instructions to tell us what is going on. Never explained the USB jacks and never used them so WTH are they for
How many Amp output this power supply can give?
5 max
Whats the resistance of the Potentiometer
10K Ohm
The cool cool cool...
3:50
Instead of background music , please explain the changes you are doing , and why that changes are necessary
But miter me 5 volt dene hote he ap ne 12 v diye he. Kya me galt hu kya
Need the complete schmatic of the entire project such as the wires from the two 10k pots wired to the small board .the video from start to
Finish to be slow if you need my
Email you can send it to me directly.
unfortunately, this video is all that remains of the project
When you soldered the 3 white and brown wires on the pot .then you removed the blue
Square pots from that converter board
Where is terminal 1.2.3 on that
Conveter Board to match the 1.2.3 wires from the pot to be soldered
on that converter board
@@paulperaino8594 wires are soldered from left to right, from the bolt
@@crafttime3360 what bolt? however, when you soldered the wires on the terminals of the 10k pot where is terminal one,two,three starting left to right? then on the converter board where is terminal one two three when you solder those 3 wires as shown in the video
@@paulperaino8594 instagram.com/p/CFomAVyh8QK/?igshid=1bvlt3rb1tkal
Post your schematic sir
can you send a slower video or schemtic
ruclips.net/video/LzvQ7S5sZaI/видео.html
this is NOT a Lab Bench power supply as it is far too noisy and the waveform sucks. It is just a power supply.
any ATX power supply can be converted to a variable lab bench power supply with a few modifications, and there are too many videos on RUclips showing how to do it.
@@diegof.8052 Quantity does not relate to validation; it does not mean they really know what they are talking about. Consider how many call an USB 'charger' a mobile phone charger when in fact it is a power supply and not a battery charger. I suspect when you know more about power supplies you will regret this post. Instead of watching crap you might watch expert channels like GreatScott.
@@diegof.8052 Here are two very simple questions for you. 1) What are the three basic types of loads? 2) Which ones will this PSU handle well?
Thank you
Nice
thank
Sent your whatsapp No
I want to buy this product
❤