CNC Controllers Built Incorrectly (Volume 26)

This video covers RUclips content creator/influencers who built CNC controllers on their channels that were built incorrectly either using incorrect components, missing proper grounding, using incorrect electronic enclosures, providing misinformation, or a combination of the above.
Please due your research before following any content creators video as the content they produce are for entertainment, and best practices are seldom followed, or understood.
If you have questions, or require quotes please message me direct at [e-mail] or through my eBay store here. www.ebay.com/s...
Below is a link to my CNC components that support the issues covered in this video along with other products to support your builds.
These are my new complete DS Flexion double shielded ultra flex cable motor kits including tool less mounted ground bus bar.
All required connectors are included, and all you require is solder, and flux which I can include as well. Let me know.
3 axis - 30’ - www.ebay.com/i...
3 axis - 45’ - www.ebay.com/i...
3 axis - 60’ - www.ebay.com/i...
3 axis - 75’ - www.ebay.com/i...
3 axis - 90’ - www.ebay.com/i...
4 axis - 40’ - www.ebay.com/i...
4 axis - 60’ - www.ebay.com/i...
4 axis - 80’ - www.ebay.com/i...
4 axis - 100’ - www.ebay.com/i...
4 axis - 120’ - www.ebay.com/i...
Pro-Grade CNC Electronics Enclosure Pre-Milled (EMI Shielded) 19W x 24Lx 8.75H www.ebay.com/i...
CNC Ground Buss Bar System Complete With SC25-8 Terminals And 2Ft. Ground Strap www.ebay.com/i...
CNC Power Supply 48v 12.5a (600w) With Built In EMI Filter
www.ebay.com/i...
Zippy VW1 (IP67 Rated) 3 Waterproof CNC Limit/Home Switches
www.ebay.com/i...
Zippy VW1 (IP67 Rated) 4 Waterproof CNC Limit/Home Switches
www.ebay.com/i...
Here's a link to my Ethernet Smooth Stepper turnkey package www.ebay.com/i...
Here's a link to my UC-400 Ethernet Turnkey Controller package www.ebay.com/i...
CNC 18/4 Double Shielded Pre-Built Motor Cable With All Required Connectors
www.ebay.com/i...
CNC 18/4 Double Shielded Built Motor Cables (3) With Dual GX-16 5 Pin Connectors
www.ebay.com/i...
CNC 3-18/4 Double Shielded Pre-Built Motor Cable & GX-16 Filtered Connectors
www.ebay.com/i...
CNC 18/4 Double Shielded Pre-Built Motor Cable & GX-16 Filtered Panel Connector
www.ebay.com/i...
CNC Double Shielded Breakout Communication Cable (Gecko Drive, Onefinity CNC) www.ebay.com/i...
CNC Cooling Fan 30-48v 60mm x 38mm (65CFM) Tool Less Mount, Fan Grill, & Filter www.ebay.com/i...
CNC Cooling Brushless Fan 30-48v 60mm x 38mm (65CFM)
www.ebay.com/i...
Terminal Splitter Kit For A/C Input 110v/220v (Gives 12 Outputs To Split Power) www.ebay.com/i...
This is my DS Flexion (Ultra Flex) cable.
CNC VFD Cable 10ft 16/4 DS Flexion For Spindle .8Kw 1.5Kw 2.2Kw 4Kw 4.5Kw www.ebay.com/i...
CNC VFD Cable 15ft 16/4 DS Flexion For Spindle .8Kw 1.5Kw 2.2Kw 4Kw 4.5Kw www.ebay.com/i...
CNC VFD Cable 20ft 16/4 DS Flexion For Spindle .8Kw 1.5Kw 2.2Kw 4Kw 4.5Kw
www.ebay.com/i...
This is my standard 16/4 double shielded spindle cable. (If you're using a cable chain, then my DS flexion cable should be used)
CNC VFD Cable 10ft 16/4 Double Shielded For Spindles www.ebay.com/i...
CNC VFD Cable 15ft 16/4 Double Shielded For Spindles www.ebay.com/i...
CNC VFD Cable 20ft 16/4 Double Shielded For Spindles www.ebay.com/i...
CNC VFD Cable 30ft 16/4 Double Shielded For Spindles www.ebay.com/i...
Here's my 22/2 double shielded accessory cable.
CNC Double Shielded 22awg 2 Lead Cable (20ft.) (Bullet Proof Protection)
www.ebay.com/i...
CNC Double Shielded 22awg 2 Lead Cable (30ft.) (Bullet Proof Protection)
www.ebay.com/i...
CNC Double Shielded 22awg 2 Lead Cable (100ft.) (Bullet Proof Protection)
www.ebay.com/i...
Here's links to the GX-16 prewired connectors discussed in the video.
CNC GX-16 3 Pin Male Panel Mount Connector Wired Silicone Leads & EMI Filters www.ebay.com/i...
#PlasmaCNCScreenSet #Mach3Tools #CNCMachining #PlasmaCNCUpgrade #CNCSoftware #Mach3Plasma #AdvancedMachining #PlasmaCutting #MetalworkingTech #CNCOptimization #PlasmaCutters #PrecisionMachining #Mach3Enhanced #DigitalFabrication #CNCCommunity #EngineeringSolutions #MachinistLife #AutomatedCutting #IndustrialTechnology

[@michaeld384]

Only two words does it for this video
Thank you 👏👌👍

[@corvetteguy50]

Thank you for your support! I really appreciate it. Vince

[@markpoulsen6429]

I use degreaser all the time... on car and motorcycle parts. When they are covered in dirt and grease. The tote full of wires being degreased was certainly a new one.
Thanks for doing these, much appreciated.

[@corvetteguy50]

Thank you for your support. I believe as I said before some things have to be seen to be believed. Thank you,
Vince

[@andydemin3105]

as much as i hate soldering ... i do try to do it the right way...

[@petermcauley4486]

I get all the call outs your doing on what NOT to do, and your focus on that is thorough.....but can you put some more focus on explaining the CORRECT thing to do. ? Cheers and keep up the good work 👍🏻

[@corvetteguy50]

Peter my channel has well over 450 videos showing everything from soldering, to full IDS system builds like this one. ruclips.net/video/Hik7SlkX5Is/видео.html
Use the RUclips search bar to help yourself to what topic you would like to cover, and stay tuned for a pro grade integrated system unlike any other available currently on the market!
Thank you,
Vince

[@petermcauley4486]

Will do mate, i will check out some more of your vids no prob, im retrofitting my table. Im at the layout stage of the enclosure, centroid acorn, etc with its fiberoptic connected thc ! Cheers

[@andrewthoma8938]

How does one get ahold of you for your services. I have a new CNC control that is not working as it should. UC300 ETH and proma 150 issues. Thank You!

[@corvetteguy50]

Thank you for your support. Please contact me by viewing the videos description as it has my information to schedule a consultation. Thank you,
Vince

[@moodon3127]

super bosss

[@amaythakkudu3839]

You you showed his face! Was it a mistake! May be I was wrong

[@amaythakkudu3839]

By the way Vince, Can We avoid interference by making a separation between PSU and other sensitive parts using metal. Or distance is needed. ? I was thinking to place the high power components behind the base plate and rout the leads through holes. Any better?
Along with ferrite and grounding too
Or distance is necessary rather than. Metal barrier?

[@corvetteguy50]

Ferrites, and double shielded cable are best suited for sensitive electronics our robots use.
Distance is only applicable to locations of VFD's from CNC chassis for EMI reduction as electronics in the same enclosure is simply not enough distance.
Thank you,
Vince