Oil Filter Stuck on Engine?
HTML-код
- Опубликовано: 11 мар 2021
- This was the worst case of an oil filter stuck and mangled I've ever run across. What should've been a 15-minute oil & filter change turned into a 3+ hour ordeal. Hopefully, my solution will help someone save some time.
Авто/Мото
Ended up just removing my entire filter housing when I tried all those methods and failed. Then found this video and after seeing that genius tool you made, smacked myself for not having done the same. One of those "why didn't I think of that" moments.
Yes I was getting pretty desperate when I came up with that solution. Unfortunately ended up having to pull the engine anyway because internal damage. Good practice for me I guess!
You're right panic is the right word.
I'm 9 months late, but definitely the right word.
It’s 10:12Pm, pouring rain, I was supposed to leave town 2 hours ago.
Panic is fucking right.
Excellent tool can you bring it over I'm in the same boat right now
Going through this nightmare right now. Simple oil change has turned into days of stress and frustration. Limited space around the filter making it one of the biggest job’s I’ve ever done on a vehicle. Thanks for the video🙂
Sounds like you need to make your own tool!
Just had a similar bad, bad day! I own a 1993 Honda Civic Del Sol. Almost no area around the filter at all which means that when installing a new filter make sure it is HAND TIGHT ONLY!!
Similar issue faced now. FSH from agents, but they obviously thought that the entire vehicle is held together with 2 fasteners: the oil sump plug and the oil filter..... So unnecessarily tight, if I apply any more leverage I risk flipping the car onto its roof....
2nd oil change now and I have skipped the filter thanks to my mechanic which he defended that if it’s not tight it would risk leaks!!! I’m a home mechanic with little tools, experience and time so I haven’t gone full gung ho mode on the stuck filter. Just wondering why would it get stuck like that? It’s ridiculously tight as I imagine the one who screwed it on tight in the first place would have also damaged or dented the filter housing? Any ideas?
@@hugostiglitz1109 Think the main reason it’s stuck on so tight is because there is a rubber seal around the bottom of the filter where it butts up to the crank case of the engine. This seal can eventually end up welding itself to the surface of the case due to the heat from the engine. So the reason it’s difficult to remove is either that or it’s because the mechanic who fitted it just put it on far too tight and also maybe didn’t oil the seal prior to fitting it. Always oil seal prior to installation and only screw on hand tight.
Hope that helps if figuring why and how it’s become so tight.
Stuck filters can make a simple job into an absolute nightmare.
I have watched a million videos on RUclips about nothing. This little gem right here was what saved me when faced with an oil filter from Hell.. Thanks man and keep posting..
Glad to help, I thought I was gonna have to ditch the whole motor because of that stupid oil filter.
Just wanted to let you know that I used this same method to get my filter off. I simply measured the diameter of the hole pattern on the stuck filter. It had 8 holes, so I knew they were 45 degrees apart. What a great idea!!! Thanks so much!!!
Hello Sir, My name is Matt. I just wanted to let you know how helpful this video was. I change the oil every year on my inboard/outboard 5.7L Volvo Penta engine Four Winns boat. Last spring unfortunately I used a filter wrench to tighten down my oil filter to make sure it was on very good. (bad mistake on my part, and have definitely learned my lesson). This is my 4th summer with the boat and take care of it very meticulously. As I started a week and a half ago to start the oil change process, everything went as normal until it came time to take off my oil filter. Let me remind you it is on the bottom of the engine block and just favors the right right side of the stern. It is extremely difficult to get both hands on and even see unless you lay across the top of the motor and have your head upside down with one free hand to hold yourself and another to work. The hull of the boat is 4 inches below it and stringers about 6 inches to the left which make it very difficult to wrench. In the last week I have purchased/borrowed 4 different filter wrenches, channel locks, large vice grips and oil filter pliers. I attempted some oil filter hacks using 2 sided tape, latex glove, etc., without any luck. The oil filter simply would not turn or budge no matter what. After everything, a few days ago I pierced a phillips screw driver through it as well and with every exhausted effort could not get it to to turn. After all this and many hours of different positioning and efforts, I asked my marina mechanic to take a look at it and see what he can do. He called me the next day while at work and he told me he wanted nothing to do with it. He also said due to its location and limited space he would consider pulling the motor if he did. I couldn't believe this was happening and what I was hearing over a simple oil filter change. The cost of lifting a motor that size out of the engine compartment is over 700-900$. I finally after watching many videos came across yours. I wish I could post pictures on the comment section to illustrate everything but it wont let me. I watched this video, chiseled the can off after about 2 hours hitting it with hammer and limited space. I cut out 2 teeth with a grinder on a socket I bought that matched the diameter of the new filter I had and made sure they lined up with the holes. It wasn't easy, it took almost 4 hours of attempting over and over again to get the teeth to catch and start prying without the socket falling out due to working upside down and not having 2 hands to work with. I had a 45 degree socket wrench attached. I felt defeated and thought maybe this socket I made was not working or maybe needed more teeth to bite on it, but I went back down and made one last effort and couldn't believe after everything I had pulling I felt it turn a little bit. I then racked the wrench back a few and started to hear it loosen as I wrenched and got this freaking thing off finally. What an incredible feeling came over me as it started to loosen after all these failed attempts. I had to tell my story and let you know your video was a game changer and I don't think I would of gotten it off any other way. I was defeated and almost quit on this thing and was going to have to pay to have the entire motor pulled out. This idea and that socket prevented it man. I really appreciate it and wanted to thank you, sincerely - Matt! ( the guy who will never tighten a filter down with a wrench again lol)
Also, If you have an email I could send you some photos of the limited space and the socket. Thanks
Wow, I can only imagine how tough that would be in a boat engine compartment instead of a truck! The favorite part of your comment that I can totally relate to is that awesome feeling you get when you realize you just loosened it a little bit. At that point, you know you were going to win! Thank you for taking the time for making this comment.
You can send the pictures to jwml1984@outlook.com
Yeah I started shouting in joy and woohooing out loud all by myself lol. This socket was clutch man, saved me big time!
im the same boat right now with my AmSkier !!!!! ugh!!!!! can you send me pictures???? yesterday oil change turned into a nightmare!!!! stinegreg@yahoo.com thank you!!!
Unfreaking believable !!! I was about to slap a grenade on mine. Never been so pissed off in my life!!! You sir are a life saver! I was trying to make a spanner wrench work to no avail because of space and thought I would make one last effort and check RUclips. Bingo! Im on my way to the store now to make your genius tool! I do believe a statue of you should be put up in town square!! LOL Thank you for sharing that idea!!
Thank you! It was the most frustrating oil change of my life!
Greetings! I would like to take a moment to thank you!! This is my first time commenting on RUclips, but the problem I encountered and the solution you provided warranted a response and a subscription to your channel. I was performing a "routine" oil change on my girlfriends 2017 Subaru WRX and when it came time to twist off the oil filter and place a new one I found myself in a rather unfortunate and highly frustrating situation, your description of panic is right on the money with how I felt. After breaking a oil filter wrench while attempting to remove it I continued to the screwdriver method leaving me with the same result you had there, just the bottom of the oil filter still attached to the thread and nothing to grab on to except the holes in the filter. After already having beat the damn thing for 1 1/2 days I came across your video and I am so thankful I did! A quick ride to Home depot and 8$ later for a 28mm socket my buddy and I were able to grind down the socket to leave us with 3 teeth, not as many as yours but still did the job. They do sell a tool specifically for this called the Universal Adjustable Oil Filter Wrench but from the reviews it seems that they're usually too big for small automotive oil filters and usually better suited for big trucks and rigs, so I used your method. 20 Minutes grinding and about 30 seconds of twisting and off it was! The relief and sense of accomplishment after causing such a situation was great! Multiple people I showed your method to were unconvinced and said I would have to just grind the whole thing off and put a new oil filter housing on but were all proven wrong and you sir were 100% correct. After a quick oil flush (on the 17 WRX the oil filter faces upwards and sits on top of the engine so I was worried about debris going into the oil.) I fired her up and she's running as smooth as ever! So thank you again! And if you're ever in the Albuquerque area of New Mexico I'll gladly buy you a beer!
Thank you for your comment, and I am glad you were ultimately successful! It sounds like you had a longer project with your oil filter than I did when I ran into this problem but as long as you ultimately prevail, that’s what counts.
Forgot to add, looking forward to that beer someday!
You have no idea how much I appreciate this video & your superior knowledge. We had to make the modified socket for my 97 Chevy Tahoe & it worked like a charm when all else had failed. Thank you thank you thank you!!
Dude, i did the same thing with my old 74 Pontiac LeMans. I made the mistake of taking it to a garage and having my oil changed because i didn't have time. That was years ago, but it's awesome to see something else has a brain.
Cool, 1969 Pontiac LeMans was one of my first cars, loved it.
Thankful for this video. It was easier than I thought it would be. I was at a total loss on what to do. I made mine off from a new filter and didn’t have to use the putty method.
Whatever works, as long as you got it off!
Thanks for the video. I was able to solve the problem without making the tool you made, but never would have figured it out without your video. On my vehicle, the threaded piece in the center, where the filter screws on, had a 5/16 hex center. I went to the hardware store and bought a 5/16 hex coupler. It fit perfectly in the center piece and allowed me to use a socket wrench to unscrew the filter mount. What was left of the filter came off with it. I then put the remains of the filter in a vice and unscrewed the mount from the filter. Finally, I screwed the the mount back into the vehicle and replaced the filter. The hex coupler cost $1.75 and I didn't need to make a new tool.
Genius solution!
This helped me out a lot yesterday and worked when all other attempts failed. Thank you!
Glad to help!
So glad you shared. Thank You! No problems, only solutions
You're welcome!
Thank you very much! I can't imagine how much money you just saved me in tow truck and mechanic costs by using this method!!
Glad to be of assistance!
Two weeks ago, I spent 3 1/2 days installing a new faucet assembly in my kitchen sink. I feel your pain, brother.
Great video, this is good stuff! Sorry about the truck but damn I’m just as glad you got that filter off! Haha I think some of us have been in a similar spot. There is just a great message in there and I appreciate you taking the time to post this!
Thanks, the story has a happy ending because now I’m building a 383 stroker for it so should be a nice upgrade.
Team effort in our household. The oil filter looked like yours in the drain pan by the time I finished with it. Couldn't use the filter removal tools we had, my upper body strength wasn't enough, and the screwdriver (which worked on another car) just made a mess of the filter so I pull it apart until it was just the ring with the holes left. Hubby then got under the car with long needle nosed pliers and a tire iron (leverage) and he finally got it loose. We've only owned this car since December so it was the first oil change we've done. Whoever put that filter on used brute strength and no oil on the ring.
Thank you sir I’ll try this tomorrow you saved me a lot of time and money
Necessity is the mother of invention,i got the same problem and plenty of sockets Thank-you much,great idea
Great video & effort!! Totally understand where you are coming from. I have the same problem to what should be a simple change out.
Great video going with your option tomorrow! Amazon, Bogert, Talon and a few others usually sell the tool part #10100 $45 put in production will take almost 2 weeks. thanks again!
This is the exact video I needed. My new Kubota tractor has a factory installed oil filter fused onto the engine block. I tried a few things like the wrench cup before my old faithful and put a screwdriver through the filter shell. The screwdriver failed and started to rip the shell so I upgraded to a spud wrench for more leverage. As expected it tore the shell apart. So I removed the shell to clear away the jagged metal and now have a fused steel piece stuck to my engine block.
Seeing this video I'm going to hit my garage tomorrow and try your trick. I truely hope it works for me since the alternative is take it in to the dealership at a shop rate of $179/hr.
I have a Kubota L3301, but so far it is only been dealer service so I haven’t run into that yet
Great stuff! Extreme measures for extreme situations!
Brilliant solution WELL DONE SIR ! Cheers Eddie
I seen your video and made the tool! Worked great!! Thank you for posting this video!
Glad it worked for you!
Thank you. You are the cool uncle. My first oil change by myself and This happened to me yesterday and I've been going ape crazy with this.
Seems to happen to a lot of people
Just happened to me.. exactly the way it happened to you. Came to YT to look for ideas on a tool to build. Definitely using this, thank you.
Glad I could help
Just had the same issue..for anyone who is interested for their own sake, I punched a crescent wrench through the oil filter and then twisted it...after 1.30hrs of trying other stuff, this method worked. Crescent wrench is thick and did not tear at the filter!
Awesome tip. Not sure if I'll have to go to the same extreme, but it's quite possible. I bought a truck that sat for 10 years. Tried changing the oil today (sub freezing temps outside) and couldn't get the filter off. It got crushed really good though 🤨
You have some ingenuity going for you buddy!
I had the pleasure of being the victim of two Conan’s who put filters on. As you know the first thing they didn’t do was put oil into the filter because they would have at least accidentally left some on the o-ring.
Yeah a dry o-ring is a real problem and if it’s a filter that is not easily approachable you better make some lunch.
97 454 dually and my 99 Dodge 24V Cummins were victims of the Barbarian!
Thanks for sharing the bad experience! Great job!
Thanks James! This went beyond anything I've run into before...I think it was a combo of extreme overtighening, no oil on the o-ring and age.
DUDE THANK YOU SOOO MUCH YOU ARE A GENIUSS I WENT THROUGH SO MUCH TRIAL AND ERROR BECAUSE I KEPT MESSING UP THE SOCKETS AND THE HOLES ON MY FILTER WERE WAY SMALLER BUT AFTER SO MUCH TRIMMING AND CUTTING I FINALLY GOT ITT 😀 😊 😄 SO I CAN OFFICIALLY SAY I LEARNED A LOT THROUGH THIS PROCESS ESPECIALLY USING THE DREMEL TOOL HAHAHAH 🔧
Yes, it was quite a learning experience for me too!
This is the greatest video I've ever seen.
This made my day. I’ll be crafting a new tool first thing tomorrow morning.
Fantastic video! Every time I buy a NEW motorcycle I have been faced with the same problem of an oil filter, factory installed by KING KONG, which is very frustrating for sure. I do ALL of my own maintenance on all of my vehicles and have a full size, 4 post Hydraulic lift that makes things much easier. I also must have 20 oil filter wrenches and sometimes must use a large pair of 'Channel lock' plyers to do the job. Funny thing is, is that the 'Owner's manual's,' always warn against over tightening all connectors and especially the oil filters!
The factory guys don’t read the manuals! 😂
That is damn great idea awesome job I been a mechanic over 25 years had some really stuck filters but not that bad damn but that is a super cool idea
Thanks I thought I was gonna have to throw that motor away if I couldn’t get that filter off. Then as it turns out, I had to trash that motor anyway because it’s junk! But it was a learning experience.
Having problems getting the old one off my '94 XJS. Thing I can't figure out is that Jaguar very clearly emphasizes that a new one should only be put on by HAND tightening (about 1/2 turn after contact made). So, why is it so damn hard to get them OFF by hand (assuming the PO followed directions)?
More often than not, the last person to change oil over tightened it. But, sometimes the rubber gasket can harden and really stick to the mount even if it was put on correctly.
I like your style. Good thinking. Adapt and and overcome.
Thanks! Worst one I ever had to deal with.
Sir, i neeeeeeed that socket. Lol
Im going through the same exact situation
3 days now 🙄
i had the same exact idea, was just wondering how to create what i needed.
Ur a genius. Now i have to figure out how to create that socket.
Thank you, greatly appreciate it. 👍
Pretty easy to make, it saved me!
This was brilliant, I was stuck in the same situation and all the other tutorial where "jam a screwdriver and beat the shit out of the filter and destroy everything. Then I found your video and it save my day !! Worked perfectly thank you .
Glad it worked for you!
Thank you so much! I am in the middle of fixing up a 1977 Trans Am which hasn’t ran since 2007 and before that was probably parked since 2005. In the middle of taking a lot of stuff off and literally went in your order, the filter cap wrench, then tried the claw (starting puncturing the filter), next goal is screwdriver but I was worried about what if it chewed up the filter with no luck. Wasn’t sure what I was going to try after that. I’m not able to remove the oil filter housing because there’s on bolt underneath the exhaust manifold and also the exhaust manifold is harder on the passenger side to take off, and at that point I may as well remove the whole engine since all the lines are disconnected from it. I’m going to try the screw driver method but I’m sure it won’t work since the claws I used where a combination of claws/locking pliers and it was really bitten down on there and no luck.
Keep at it, you will eventually prevail, hopefully without pulling the engine. If you’re willing to sacrifice a socket, can utilize my final solution.
@@pinkcaddygarage267I would definitely give up a socket before pulling the engine. Thank you!
Good deal! That may be what I end up doing. The filter strap crushed the filter, and the filter pliers crushed it further. I now have a hole in the filter and I'm removing the driveshaft on the front of the 4-wheel drive.
That’s pretty much what happened to me. Everything I did for the first few steps just destroyed the filter housing more and more until pretty much the only choice I had left was to deal with the filter base that was stuck on the engine!
Thanks for sharing. This happened to me, i ended up using the strap method. Lucky, it worked. If that didn't work, i was going to use your method.
Good thinking. That was smart.
Before you puncture the filters case, try starting the engine while working on filter. The oil pressure will prevent the filter from collapsing and lub the contact points as it loosens.
After traditional oil filter wrenches dented and distorted my Motorcraft oil filter (on E250 Ford van), I tried a GIANT MONKEY WRENCH while lying on carport floor underneath the van. With a great deal of effort and more denting, the filter finally started turning, and I was able to get it off. I experienced the frustration and panic.
Omg that’s a nightmare I’m dealing with something similar now 💔
Omg you need a check for that get the tool made and sell it hood job man 👍🏽
Thanks Mr genius i also managed to make the tool n take the remainder if the oil filter on my Vw..
Thanks! Brilliant idea!
I had one like that yesterday, first oil change after purchase of a nice, low mileage silverado. I wound up using an air chisel to work it off, but damn IDK who put that on so flippin' tight!
Well, they wanted to make sure it wouldn’t leak.
had the same issue the other day I used my socket I had for doing 4wheel drive hubs . didn't have to mod anything I will be posting up the video tomorrow
OMG! How long had that oil filter been on the engine?
That's The type of tool found in old mans garage At estate sales that Starts conversations or puzzle's the Young people .My Uncles garage was full of SHTF Home made tools .That's the finest example Ive seen. Patent it and sell them for a while at least until another country rips it off and makes knock offs of it
Thanks, I just turned 61 so I may be qualifying for the “old man “ status.
@@pinkcaddygarage267 Looking great for 61 my man.
i appreciate the video. i have a more modern filter cap thou its plastic im wondering if torching it would be the way to go once all else fails
It sure if adding fire to the problem would be recommended 😀😀
@@pinkcaddygarage267 lol yea after i read it i saw how silly that was
You just saved me thank you for your video!
Glad to help !
Hi it's me again whilst I was explaining your brilliant method to Gill my wife a thought crossed my mind (can't spell 'occured ' ) does the socket have to be very deep to accommodate the threaded thingy that the filter screws on to ? Cheers Eddie
Sorry, just saw your comment. No, it just needs to be deep enough to engage the filter ring.
Hi thanks for your reply ! it takes quite a good number of turns to screw the filter on ,so the threaded 'thingy' must go inside the socket preventing the 'forks ' engaging the holes at the bottom of the filter can unless the socket is extra deep I presume the 'filter ring ' you refer to is the bottom of the filter can .Cheers Eddie PS I never expected a reply ! I still think your method is brilliant !
Hi its me again ! if a deep socket is not available a steel tube could be used instead, with a tommy bar used to turn it ( I think its called a tommy bar ) its the thinner solid bar going through the hollow tube . Cheers Eddie.
I was in same position nothing left to work with but holes. Saw my disc cutter blade removal tool with prongs. So I got my largest width spanner drilled the jaws and placed 2 bolts through. Slotted into filter holes and bingo came off un a second. After 4 hrs pratting around. Not even wrecked the spanner. Was on a motorcycle stored for 12 yrs. I bought it and worst job ever done
Great idea. I am stuck now, time to cut off the remaining oil filter...
Hopefully you will have less trouble than I did.
I think I'm looking at the same proposition to get the filter off the new JD Gator for it's first oil/filter change. Two other filter removal tools failed to budge the filter and should get the Lysle filter grabber tool tomorrow. It will either destroy and/or turn the filter. If not it's the torch and screw driver and then that socket you built.... Can't get any pliers into where the filter is located so that option was out also....
How did that work out for you?
@@pinkcaddygarage267 that worked out well. It was able to seat well on the filter and lightly crush the filter and hold on. Needed a breaker bar to loosen it though.
Very Ingenious!!!!
i did a similar thing to get a bathtub drain out since it was a weird size i found a piece of steel pipe and just cut notches in the end with grinder and cutoff wheel to fit the cross piece in drain then just twisted the pipe with a pipe wrench on end
Genius.
Missenden Flyer also has a similar (kind of solution) that involves drilling holes around the edges of one of those "crown" or "cup" type filter removal tools. Then put the cup on the filter, drill through the holes into the filter. For however many holes you can reach, screw in some screws. So the cup and the filter are screwed together.
It worked for me.
Just saying.
Sounds good, I didn’t think of that!
@@pinkcaddygarage267 See also -- Bogerts talon oil filter tool -- A bit pricey, but might be good as a last resort.
Cheers!
Today I was defeated. Tomorrow, that oil filter will fall.
The idiots at the oil change shops are the ones the generally cause the need for a video like this.
Change your own oil folks. Hand tight. That’s all. It just needs to seal. It doesn’t need to support any load or high speed rotation.
Either that or the guy that owned it previously literally never changed the oil and so the oil filter eventually became hardened onto the block because the rubber seal will do that!
That's called Ingenuity!!!
Thanks!
thank you sir
I'm having the exact same problem now. Read all comments. Will try this but not sure how easy to make this tool yet.
Before using your method, I tried the other trick because yours requires to build a special tool which should be quite hard. I have thought about several revisions of your tool. But I first tried to use nose pliers to hook up the filter holes, and used a break bar to turn the pliers and it finally worked.
im having the same issue with my boat oil filter, what a great idea!!!!! I told my wife if I cant take it off, we are going to have to pull the engine out because there is no room to get a bar in there, cross my fingers
Any way to modify a socket and get it in there?
you, sir, are awesome
Desperate times call for desperate measures.
Nice video, but what if the problem is with a 4x4 V6.5 Suburban 95... i dont have space for any tools and my filter is already destroyed
Did you solve this yet? If you can’t make room you’re going to have to start pulling parts off to create some room. Alternatively, the engine can come out.
@@pinkcaddygarage267 yes I did it. I finish with a big cut in my finger but I did it :). Thanks for asking!!
Stuck Acadia oil filter in tight spot just would not corporate. Your modify a socket to fit inner plate holes worked. These engine design engineers should be subject to hot greasy garages trying to fix their screwed up designs. Thanks for the help
Sometimes extreme measures are required!
What did you use to cut the socket down?
Angle grinder with a cut-off wheel
I had the same issue last week then i used my wife's hair blower to heat up the top of the filter to melt down stuck oil it worked like a charmed
Never tried that before
Great Idea
Iv been there.....Great idea!!! 👍👍👍
................... Great idea ..........
I am going through this with my ATV right now. Did just about everything he mentioned
Did you win or did the oil filter win?
My car is just out of warranty, so was always getting it serviced by a mechanic to keep it in warranty but now is the first time I'm doing an oil change and OH MAN, I've got the same problem. Stuck oil filter and using traditional oil filter removal tools the filter looks so stuck it looks like the outer metal casing is going to rip apart like an aluminium drink can.
For some reason, I feel like I'm seeing the tiniest of squeeze out from someone having put threader locker on the threads. Did the mechanic do that, to force me to bring the car back to them?
So, I've been trolling the internet for a week looking for a solution and this video seems to be the real answer.
I'm currently doing stretching exercises, rolling my head around to loosen up my neck, cracking my knuckles and otherwise getting mentally prepared for what looks like a multi hour battle I'm about to enter, based on this video and comments from others who have had the same issue.
Once I've started down the road of this solution and the outer filter casing is ripped, I need to finish with getting a new filter on as it's my only car and I live in the bush and my driveway is 200 metres long on it's own.
If this solution doesn't work. I'm just going to cut away as much of the filter as possible and sand down the threaded part of the filter till it's fragile enough to break off with a pick or a screw driver...being very very careful not to sand down so far as to touch the threads on the engine.
If my engine block was cast metal, I would've just taken a torch to it, to soften up the aluminum filter threads and if I was extra safety conscious, have an extinguisher close by to put out any oil drips that may catch on fire but like most people, will probably use a oily rag to smother any spot fires and then be surprised and a little bit panicked as the oily rag sets on fire.
You unthinkingly and immediately pick up the burning rag with your oil covered hands. Your oil covered hands, the stuff covering your hands that's already on fire, on the rag. Yet you persist and grab the burning rag and throw it away from you and your car while swearing a lot, like it was someone else's fault the rag caught on fire.
Aluminium melts at about half the temperature cast metal melts, so there's a good safety margin there.
Were you successful?
@@pinkcaddygarage267 Yes, I made up my own removal tool using a push bike chain.
It was rough as. An old 4x2 that I took a jig saw to one end to make it closer to a 2x2 and then I nailed, into the end grain one end of the chain. I used two nails through the end link and bent them over.
I then got under my car and wrapped the chain around the filter 3 times in an anti clock wise direction.
The loose end of the chain. I used a pair of vice grips to secure the chain against the, "handle" part of my device.
I really jammed down with the vice grips and the chain dug a bit in a little into the wood. It was some sort of pine.
I was surprised. The first wrench on the oil filter with my contraption, I thought I saw some movement. I then thought, nah, it couldn't be that easy.
I repositioned my device and gave it another yank and yes there was movement.
I thought to myself, "You've got to be joking me. All of this drama and all I had to do was make a janky home made tool and I could have been finished ages ago"
I put down my success to the extra area and bite my tool had on the oil filter.
I was thinking of a better version of welding an ordinary chain onto a pipe and cutting a slot in the pipe and putting a threaded rod inside the pipe with a backwards facing bend coming out of the slot and use the bended rod part to go through a link to hold the chain after wrapping it around a filter and put a nut on the threaded rod sticking out the back of the pipe that you'd ratchet down on to pull and tighten the chain onto the oil filter and that would make for a tool worthy of being put in the tool box.
Brilliant!
Just did this.
Thanks for the idea.
Glad it work!
@@pinkcaddygarage267
I was out of options....... little time and grinder, and you weren’t joking about the breaker bar.
I’m feeling like I won the day.
Gracias
All the frustration goes away when that thing finally starts turning!
Gold!
I got one for ya to make you feel better 😂
I was changing my oil while on the phone and I changed the filter and added oil and forgot to drain the pan 😂..
I figured it out later
I bet you did!
How about using an air impact instead of extension?
Would that be trouble?
Air impact would not budge it.
@@pinkcaddygarage267 Oh my.
I see two option in my minds eye at the moment for tomorrow.
1. ratchet strap tie down wrapped around the filter few times. and secure the other end to something across the filter. this way instead of pulling on the filter, it will turn it when it is cranked.
2. Them metal caps that go on the filter and takes 1/2" rertchet. Mine have 4 holes at its bottom.
Feed 3/8" , 2 inch long biolts throiugh the 4 holes and into the filter and see what happens.
The filter still have some body left I guess.
I have never even heard of or seen or experienced this nonsense before. It is like this device has welded itself in the block. It is loud and in my face telling me who is the boss. Weird as hell.
Might work. As long as you still have some filter body to work with, you may be able to avoid an extreme silt.
@@pinkcaddygarage267 I am happy to say that the metal cap over the butt of the oil filter split in half upon turning it. It was held by 3 bolts as there was no room to put in a 4th bolt, it would have made no difference nonetheless.
There is no place for my strap ratchet thought plight.
The wind is blowing piercing cold air into me bones right through it, just for extra treats. It cares less about me or my problems. It does not negotiate. Resistance is futile. At this rate, today is out.
Tomorrow time for a cordless saws all and a dremel and a whatever. But if it is gonna blow like today, I will have to be painfully bored to get under that cold space between the ground with a sheet metal over the gravel and the unforgiving cold hunk of metal above me....
There are no 1-800- wah-wah to call for emotional or any support. :-)
Crappy weather makes the whole thing seem worse. Sometimes I just have to walk away for a few days.
You sir are a true hero!!! Can you please autograph my socket I made..THANKS ALOTTTT
Glad to hear it worked for you!
Nearly at the socket stage now. Trying a piece of box section with two 7mm bolts welded to it. Hope it works. If not watch out socket🤣🤣🤣🤣🤣
At times a socket must be sacrificed 😃
Yup, indeed. All to a good cause🤣🤣🤣🤣🤣🤣🤣@@pinkcaddygarage267
Would you mine if I borrowed that socket, my filter is the exact same as what you showed in your video, I’m stuck and have no clue on what to do next.
You can have it!
@@pinkcaddygarage267
Like honestly, I really really need it
And I am never going to use it again so you are welcome to it. Are you in the US?
@@pinkcaddygarage267
Yes, how can I dm you from here?
Email me:
JWML1984@outlook.com
5 days of different methods this one for the 🏆
Glad to hear it!
Another way to remove a stubborn filter is to hold the filter steady, and twist the engine.
😂 I was ready to do that!
I also had this happen a few times and tapped on the screw on filter part until sucess. During my second issue a few years later, I discovered I could use a 1/2 extension up thru the screw on nipple for the filter and unscrew the nipple and filter flange. You can easily then clamp the filter flange in a vise and unscrew the two parts apart. Easier than cuting up a socket, your thinking was great, out of the box! I learned the screwdiver yrick sets you up for additional disaster.
Good idea about the flange!
Man I hate when they tighten it too tight. It makes a simple job almost impossible for a diy. I’m stuck right now trying to get one out
I feel your pain.
Punched through with a screw driver, it's just ripping it up, the strap type wrench is just collapsing it so now a third trip to the parts store, going to epoxy a cap type wrench on it so it can't slip. Cheaper than a tow.
Keep fighting the fight.
@@pinkcaddygarage267 It worked like a charm, could have put 200 lbs of torque on it.
I do not have proof, but I suspect that even if you lube a new filter gasket, and install it properly (1/4 additional turn), that given enough time, it can become problematic. I installed a filter on a piece of equipment that I have not used in 8 or 10 years, and it is now stuck, and I am 99% certain that I lubed it before installing!
You’re probably right. The rubber seal will become hard overtime and tend to want to bond with whatever it’s touching.
Improvising at its best
I would have just went to my nearest Valvoline had them to go ahead do my oil change
Maybe from the beginning to have used a breaker bar ?
Maybe, but at the beginning I didn’t know I was gonna have so much trouble.
Can I buy the tool from you
If I can find it I’ll be happy to send it to you. Hopefully I will never need it again.
Regarding your last ditch effort to get the remaining END piece off you were left with to tackle. A SPANNER WRENCH might've done the trick for you. I hope there ISN'T a NEXT TIME but.......
Same proble ,but I have another problem I’m not that clever to do what you sid
??? What is the other problem?
@@pinkcaddygarage267 can’t get my filter off it’s now shredded into pieces brand new mower with 5hours
wow more presistant than me.