Well Thank you, I hope your a subscriber, I made that Several years ago before I thought I could ever own a ultrasonic cleaner, I still use it from time to time, Thanks
If you mount a pulley to the motor with a belt going to another pulley, put the counterweight on the standalone pulley. It won't be as hard on your motor bearings.
I use Simple green ALOT in my ultrasonic cleaner and it does Great,, in my ultrasonic cleaner I can put a few drops of Dawn dishwashing liquid in 1/2 gal water and it does jewelry and most other things pretty well ,, thanks for the comment and watching 😎
Thanks Stefan, I built it several years ago when I was working on slot of chainsaws and mower & 4 wheeler carbs, I'd disassemble a carb put it in half can of Gunk and let run over nite, it looked GREAT the next day🚴🤓
Sure, it would be better then just soaking it, I used what I had and did it the way I was thinking at the time, if I'd done it a week later it would have been still different 🤔 thanks for watching and the comment
@@georgeskentuckyworkshop1420 thx for replay cant find ultra sonic in middle east After i used gas sinking method it didnt work perfect ihave to push little gas to start it Carb still blocked some how jets or fuell pipe Soo am gna go plane b open and clean
In the old days we would totally disassemble the carb and run a wire threw every hole and jet and always new accelerator pump, and always may sure fuel pump is good,,, if it's not no matter how good the carb is,, it won't run right
@@georgeskentuckyworkshop1420 my proplem on idle engine die When push gas padle or on road car work fine and it happind After sinking it in gas before on idle is good on road was bad thx for replay
I made that diy machine probably 11-12 yrs ago out of misc available to me cheap or what I already had here, way before I ever thought I could afford to own an ultrasonic cleaner, which I've only have a couple yrs now, and if I ever bought another ultrasonic cleaner it would be 4 times the size of the one I have now, thanks for the question and for watching 😎
I've gotten the same reply Many times, that simple carb cleaner I made years ago in about 15 mins had cleaned Many things for me, it was a common thing to leave it run for 3+4 days none stop, it's will be fine for what it's used for, in fact I still use it sometimes to clean bicycle chains, cassettes, and misc when my ultrasonic cleaner is full, after running that for days the motor or bearing housings are not even warm,
I looked up several videos regarding homemade parts cleaner. This was the best by far. Thank you
Well Thank you, I hope your a subscriber, I made that Several years ago before I thought I could ever own a ultrasonic cleaner, I still use it from time to time, Thanks
If you mount a pulley to the motor with a belt going to another pulley, put the counterweight on the standalone pulley. It won't be as hard on your motor bearings.
Yeah, but a belt, two pulleys, and a mount will cost more than the motor did…
Awesome!
Many thanks for a simple made cleaning solution video. I am going to make me one soon.
I might throw something like that together. Will put it on springs tho so the bench isnt soaking up so much vibes
I use Simple Green D (D means safe for Aluminium) the Aluminium doesn't turn black.
I use Simple green ALOT in my ultrasonic cleaner and it does Great,, in my ultrasonic cleaner I can put a few drops of Dawn dishwashing liquid in 1/2 gal water and it does jewelry and most other things pretty well ,, thanks for the comment and watching 😎
Thanks fore shareing great information! 👍🤠
Thanks Stefan, I built it several years ago when I was working on slot of chainsaws and mower & 4 wheeler carbs, I'd disassemble a carb put it in half can of Gunk and let run over nite, it looked GREAT the next day🚴🤓
When you say mix it 50/50, are you talking water, or carburetor cleaner?
Thanks.
Thats pretty cool. I put an electric sander on the side of the can and it vibrates
Good idea, I made mine out of misc I had in the shop, and to be honest I never thought of the sander idea😁
@@georgeskentuckyworkshop1420 well i got the idea from some guy on RUclips
Thanks, it worked GREAT for years till I bought the new ultra Sonic cleaner
What about strapping a cheap hand sander. Vibration would seem to be 100 fold. Run for an hour or so
Sure, it would be better then just soaking it, I used what I had and did it the way I was thinking at the time, if I'd done it a week later it would have been still different 🤔 thanks for watching and the comment
I far a way from shop i sinkd my carb edelbroke in gasoline iwill leave for 2 days ist gna work plz answer me?
Soaking in gasoline is better then nothing, but carb cleaner would be better and the best would be in a ultrasonic cleaner
@@georgeskentuckyworkshop1420 thx for replay cant find ultra sonic in middle east
After i used gas sinking method it didnt work perfect ihave to push little gas to start it
Carb still blocked some how jets or fuell pipe
Soo am gna go plane b open and clean
In the old days we would totally disassemble the carb and run a wire threw every hole and jet and always new accelerator pump, and always may sure fuel pump is good,,, if it's not no matter how good the carb is,, it won't run right
@@georgeskentuckyworkshop1420 my proplem on idle engine die
When push gas padle or on road car work fine and it happind After sinking it in gas before on idle is good on road was bad thx for replay
Sounds like it needs to be taken apart and run wire threw all the holes and jets the put new accelerator pump it the carb
another use for girlfriends device lol
If the diy’s so good why buy a sonic carb cleaner?
I made that diy machine probably 11-12 yrs ago out of misc available to me cheap or what I already had here, way before I ever thought I could afford to own an ultrasonic cleaner, which I've only have a couple yrs now, and if I ever bought another ultrasonic cleaner it would be 4 times the size of the one I have now, thanks for the question and for watching 😎
I know one thing - you aint from Kentucky - good video though.
Hello thanks for the comment
The offset weight will eventually blow the front bearing out.
I've gotten the same reply Many times, that simple carb cleaner I made years ago in about 15 mins had cleaned Many things for me, it was a common thing to leave it run for 3+4 days none stop, it's will be fine for what it's used for, in fact I still use it sometimes to clean bicycle chains, cassettes, and misc when my ultrasonic cleaner is full, after running that for days the motor or bearing housings are not even warm,
Mix gasoline, close de Can. then you gone see a ultra cleaning