How to Remove a Generator Armature and Stator
HTML-код
- Опубликовано: 26 авг 2024
- In order to remove a generator stator and armature you will need a puller, socket set, WD40, steel rod, hack saw, tap and a bolt. Every generator is different so do what makes sense for you and the machine you are working on. You can damage your engine, stator or rotor when performing this procedure so do not rush.
I use Harbor Freight Super Heavy Duty Degreaser in my ultrasonic cleaner www.harborfrei...
Visit My Amazon Store:
www.amazon.com...
If you want to donate to the channel, you can use the RUclips "Super Thanks" feature or via PayPal: www.paypal.com...
#GeneratorRepair #SmallEngineRepair #SmallEngine #DIY #Fixed #Troubleshooting #HowTo
![Tee Grizzley - Detroit (Feat. 42 Dugg) [Official Video]](http://i.ytimg.com/vi/aeKfTtt0x14/mqdefault.jpg)
*100% best **Generater.Systems** I have used. A test for hurricane prep here in Louisiana: three AC units, 5000, 5000 & 8000, 3 fridges, 2 device power setups, 4 flat screens....AND I had 40% of the power meter to spare.*
The thumbnail overlay showed 'EASIEST WAY TO REMOVE AN ARMATURE' and I agree implicitly; i.e., have you do it. Good vid.
Thanks
Absolutely perfect! My issue was a good five horse side shaft motor and a fried generator. I had everything I needed except the rod. The motor is on the curb now with a price tag on it. Thanks!!!
Thanks. Found an old Generac that the engine was toast. Was told the generator was working. Video showed me how to get it apart.
I also wear a head lamp when working. The guys were teased me ruthlessly in the shop 🤣
Good job! On my generator to get the housing off I just tapped gently with a hammer on the side and it came off with no puller necessary. When you actually did pull the armature off there is a threaded plug you can buy to put in the spark plug hole to keep the piston from moving so you can tighten down on the bolt without the flywheel turning.
Thanks a lot for sharing a very important information!
Put water down the hole instead of a rod to get rotor off. Then the bolt . It works .. fill hole completely with water then put bolt in . As you tighten the bolt the rotor pops off. Think it sounds crazy? So did I until I did it. Ive done 10 or more like that and it works every time . Obviously you have to stand the generator on its end to do it. Try it sometime.
That is my favorite way to do it
its helped me, so thanks for making this video!
your insight has saved me a lot of time, thx
We have used the ruclips.net/user/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!
Good Work thank you for learning how to remove armature.
Thanks. This is just the information I needed.
Glad it was helpful!
Really genius idea dude
Thanks. I hadn't done that one before and needed a hint. Taking apart the coleman 5K generator a friend gave us with bad engine, it had threads in the end already and the first bolt I tried on it from the spare bolt drawer fit perfect. That was interesting luck.
TnMtnRdr having threads is good luck never mind finding the right bolt on the first try.
Very good 🙏🙏🙏🙏🙏thank you
I tried removing rotor as you explained, I used a 12mm bolt and it was very, very tite and the bolt snapped of inside the shaft......bugger.
Thanks 👍 i have this problem with my generator. My motor seal is broken and need to get the generator of... have try this 👍
multumesc pentru informatia corecta mult succes in continuare
Thank you, now I know how to do it 😊.
It worked for me! Thank you so much!!!
At least when the engine is junk you don't have to worry about damaging the threads on the end of the tapered crankshaft. Different story for a working engine.
Correct. I use water to remove them when I think damage may occur to the crank threads.
Thanks it helps a lot
Thank you so much great technique
Sorry, should have noted that. Do not have that info now. All I did was remove the bolt from the rotor, measure the diameter with a caliper went online to find the recommended tap size. The original tap I used ended up being too tight so quickly changed the size.
And How did you simply remove the bolt ?
Garry Seloske I removed the spark plug, rotated the cylinder to bottom dead center and filled with rope to lock up the engine. You can see me doing that here ruclips.net/video/tX1sSLhNSio/видео.html
Thanks for the help
Nice . Thank you
Thank YOU
Thank you help me so blow some compressed air over the fins to get a smooth flow of clean green energy...
Been a few yrs i see; is taking off the matching shaft on the motor as easy?
Can you use copper anti seize on the motor shaft?
Thanks
111 why not just pull whole assembly at this point with bolt and rod? Remove brushes of course. Working in a black maxx, need to check seal.
Great tip 👍
Ive stuck my rod inside, and i cant get the rod or anything else loose. Any tips?😅
Ever try a slide hammer? Gonna diagnose mine one more time, if rotor tests ok be great, have another identical alt I know works. Predators only last a yr no matter what, either engine goes or now alt. With it being 100 out all week might just buy a real one since I'm off grid
James, love your videos, VERY educational! I've been a tactical generator technician, (military trained) for over 30 years, your examples are outstanding! My question to you is are you experiencing any carburetor quality issues when purchasing replacement OE types from Amazon? I get the impression there is a tremendous uptick in downsized main jet issues since many of my repairs, when using Amazon sourced carbs, begin to experience speed reductions when load is applied to the generator. The governor responds properly when manipulated however even with low load, a reduction of speed is noticed. I've even considered honing the main jet to a larger size which it generally improves performance but not the correct corrective action... but one that works. Your thoughts?
Honda clone carbs work well. Have tried Subaru, Briggs and Tecumseh clones and had a lot of issues with the jetting being off. Oddly most have been too rich.
Sir thank tou
have a link for replacement?
mines burnt up
What size is the tap and bolt?
I believe I used an M12 1.75
Sir James Condon what size of hex head threaded bolt did you used?
I have question, what size o diameter is the bolt to punch the roundbar? And the bolt is standard tread or metric tread? Please help me because now I need fixed my generator and I need remove the rotor from engine.
I think I used a 3/8 inch rod. The bolt was standard 5/16 24
Any way to remove the bolt inside if it now?
What do you mean? The rod? If the rotor is still on, I use a magnet to remove it when needed. Otherwise you would have to tip the generator to get it out.
New video
🙏🛠🎼🌹🎶🎵