Thanks very much for uploading this video we have just bought a 860 and sat trying to work it out for a few hours. This video really helped, we are looking forward to using it. Thanks again for taking the time to upload we really appreciate it.
I have the 860 and it's a beast. Loads full buckets front and back fairly easily, even in hard ground. It runs like a top and has definitely earned it's keep.
interesting video gazza, enjoyed it buddy ,funny thing is, i did exactly the same thing with ignition switch on a toyota corolla damm electrics ,lol anyway thumbs up from me :)
Cheers for the comments fellas and also sorry about the hands being purple, I sprayed them with footrot solution the other day by accident and it won't come off 😂
Howzit Gazza tell me something where is the 4x4 switch and where underneath does the 4x4 solenoid sit cause I can't find it nowhere ?this surely can't constantly be locked in 4x4?
I have a 750 and it has the same ignition problem. can you tell me how you managed to fit the starter motor button. There is very little room. I am pulling my hair out trying to find a way to do it.
On the top of the solenoid there is a positive 12 volt wire that key used to put power to the small solenoid, cut that and put a chocky block joiner there and put a positive to the switch you are going to install leaving the cut wires attached also. If you look on one of my jcb Fastrac vids I show you how to do it on there because my Fastrac has a similar problem 👍
i have fermec 965 i found all wires of joystick cut and i want to change the joystick Can any joystick electrical work for me o i need a specific joystick if you have any ideas Thank you so much Sir.
You will probably need a specific joystick for that model I’m afraid because you would make a hell of a mess rewiring a non standard joystick in my opinion. A stock fermented one would plug straight in and you’d be back running very quick !
@@onlygazza thank you for your reply can i install a new system to control the fermec? I'm thinking to change the joysticks and the motherboard.. is that possible? Thank you Sir.
@@codyharris9472 you just need a positive to the switch then the other wire joined to the small positive wire on the starter solenoid ( if you look at a vid I did last month on the Fastrac it shows you how to do it on there )
Thanks very much for uploading this video we have just bought a 860 and sat trying to work it out for a few hours. This video really helped, we are looking forward to using it. Thanks again for taking the time to upload we really appreciate it.
I have the 860 and it's a beast. Loads full buckets front and back fairly easily, even in hard ground. It runs like a top and has definitely earned it's keep.
Great video Gazza, I've forwarded this to a friend who has aquired an MF 760 and was unsure about some of the controls. Thanks again.
Evan Espin glad to help 👍
cheeres for uploading never seen a fermec digger before very interesting thumbs up from me to
interesting video gazza, enjoyed it buddy ,funny thing is, i did exactly the same thing with ignition switch on a toyota corolla damm electrics ,lol anyway thumbs up from me :)
Cheers for the comments fellas and also sorry about the hands being purple, I sprayed them with footrot solution the other day by accident and it won't come off 😂
I got one of them :)
Use one in upstate NY,USA good Machine.
Maul Sams yes they are really good and very reliable machine, all the best gaz
Howzit Gazza tell me something where is the 4x4 switch and where underneath does the 4x4 solenoid sit cause I can't find it nowhere ?this surely can't constantly be locked in 4x4?
It’s on the right of the steering wheel, a switch on the dash
@@onlygazza thanks man ,all these buttons have been by passed ,Zimbo bush style .lol thanks came right
Could you swap the pipes round on the back actor to driver on European controls pattern
TheMONTREYJACK1993 I suppose you could but it’s pretty easy to master if you can drive a mini digger, I just jump between them without noticing.
Gazza i had a go of a 3cx once was one interesting experience haha 😂
I have a 750 and it has the same ignition problem. can you tell me how you managed to fit the starter motor button. There is very little room. I am pulling my hair out trying to find a way to do it.
On the top of the solenoid there is a positive 12 volt wire that key used to put power to the small solenoid, cut that and put a chocky block joiner there and put a positive to the switch you are going to install leaving the cut wires attached also. If you look on one of my jcb Fastrac vids I show you how to do it on there because my Fastrac has a similar problem 👍
Gidday Gazza how do you remove the starter motor if the buckets down
Get under her and struggle or get another machine to lift up the Bucket, no other options
This machine is made before 2000,maybe 96,97
i have fermec 965 i found all wires of joystick cut and i want to change the joystick
Can any joystick electrical work for me o i need a specific joystick
if you have any ideas
Thank you so much Sir.
You will probably need a specific joystick for that model I’m afraid because you would make a hell of a mess rewiring a non standard joystick in my opinion. A stock fermented one would plug straight in and you’d be back running very quick !
@@onlygazza thank you for your reply can i install a new system to control the fermec?
I'm thinking to change the joysticks and the motherboard.. is that possible?
Thank you Sir.
@@goyoub7549 sorry bud that’s above my pay grade, I can barely get up on time in the morning 😂✊
How did you fix the switch mine is the same way not starting up
If you mean the starting I just put a button with two wires to the starter motor
@@onlygazza thanks I'll try that
@@codyharris9472 you just need a positive to the switch then the other wire joined to the small positive wire on the starter solenoid ( if you look at a vid I did last month on the Fastrac it shows you how to do it on there )
Someone from the group could help me with the manual of the mf 965 backhoe loader, the electrical and hydraulic diagrams.
Hola amigo buen día.me podría habilitar el diagrama eléctrico y el hyd o podrían venderme.lo nesecito urgente
I have an 860 it's 1990
Ryan Maginn cool, good machines 👍