Didn’t know I needed the Bible study class but I appreciate you throwing it in here. Just bought a boat and need to do the power trim. Hope it as east as you made it seem.
You my brother, are an inspiring example of a witness! The repair info was good, but the witness was much, much better. I pray someone is touched as a result of your faithfulness. I have an ‘87 Johnson 150 and my trim solenoids keep burning out, about once a year? Any thoughts?
Hi Jim, Thanks for the word of encouragement. I just past 1 million people who have watched these videos and it is still growing. As for the trim cylinders, if you keep replacing the seals and they start leaking again in a year, any chance the shaft might have any damage on it that could be cutting into the seals?
@@bradhawkins3687 i've used snap ring pliers with the 90 degree ends as well. works perfectly. you dont need a ton of torque to seat that seal. little gasket sealer on it is all you need.
thats the MUCH better fastrack system. just 2 pins instead of 6 seized screws to get the thing out. plus once its off you can replace the trim motor as they all go bad eventually.
Thanks for the comment. I like you suggestion just in these salt water areas were we are located the lower pin is many times no longer removable due to salt intrusion.
@@creativerepairing2960 you got it. Some are a nightmare... especially the big v6 motors as you have alot of weight on it. Relieving the pressure helps, but not by much!
I have a 2005 ETEC 50. We need to replace the O ring on the hydraulic tilt pump but we cannot get the PIN out to tilt the motor up and away to get at the O ring placement. The pin is threaded on the starboard side and we have attempted to slide hammer it out. We were warned that hammering on the pin on the Port side would cause it to mushroom and make things work. Any Ideas?
you don't need to take the pin out just to trim the motor up! unscrew the manual release on the port side 1/4 turn or so, and lift the motor up. put a block under it to keep it up, or use the trailer lock. then complete your work.
Great video on replacing the tilt seals, I have a leak in the tilt as well but dnt want to buy the whole kit ($80). Do you know the part number for just replacing the seal for the tilt.
Go to Evinrude dot com get the oem part number then go to eBay search that number with Evinrude and part number and you’ll get oem available parts and aftermarket Igot oem seals and tool to do the job and oem service manual not clymer or any other manual JT 🇺🇸🇺🇸🐟🐠🐠🎣🐟🎣🛥🌴⛱😊😊🙏🏻🙏🏻🙏🏻
He made the video because he is a Christian. Took time out of his busy schedule to try to SAVE your no trim cylinder build SELF . And maybe u should know Christ then you wouldn't have to watch this video because all WISDOM COMES FROM ABOVE !!!!! PRAISE THE LORD JESUS CHRIST!!!
Was you tilt motor making any weird noises before you changed the seal? Minen has bad seals and has recently started to sound weird. Will be attempting this soon. Thank you for this video!
Hi, Thanks for the response. It didn't make any weird noises just was leaking trim fluid at the base of the shaft. The trick to this video is realizing you can rebuild it without taking the whole trim system out of the saddle. Best of luck on you job. Thanks
go online to CrowleyMarine.com and enter your model number and get to their schematic drawings which list part numbers. From there whether you buy from them or not you can use the part number to search places such as ebay or other platforms.
The part with the nut and was hard to get off, had to use a bearing puller after I removed the nut. Trying to put it back it very snug and can’t get it back on. Any ideas?
Hi my name is Marco from germany. I have a problem with my E175FSXECS, especially the part 0435263. I dont know wich way i have to put the springs with the balls and these little metal pin together, cause i lost them during my repair work. Do you have a precise description? It would be help me so much. Best regards from germany!
Hi Marco, I couldn't give you an exact answer without taking it apart again. I would suggest you try one of the parts schematic diagrams. I usually use www.crowleymarine.com. Hope this helps you.
I got the seal kit off ebay. The tool also came from ebay but was a used OEM tool. Try searching the internet for "spanner wrench" and you will see some options. If you have a freshwater engine some of the cheap universal spanner tools will likely work. My engine is a lower saltwater use and the top came off the cylinder very easy.
@@Berkner80 I did but it is a pain when everytime you stop you still here about jesus and not what the video is describing half the video was religious mumbo jumbo
I don't agree with mixing instructional videos with religious beliefs. It's definitely poor form. I'm sure the Christians would comment about a mechanical video that had a Satanic commercial in the middle. Maybe you should place it at the end so that you don't offend people that are looking for help with there motor. Just start a Christian channel and help people without Jesus, I think he would agree.
In the Trying Times we are Living in, it would be a Shame not to have God on your Side as Tomorrow is not Promised to Anyone, we are All One Heartbeat away from Eternity--Heaven has a Great Air Conditioning System--Hell is Burning Hot and its Forever without one Drop of Water to Quince your Thirst!!!
Can't you christians do anything without preaching the gospel..?? It's a shame, because the "How to/repair" part is actually quite good. But since you ask "Are you a good person?", here is a little hint for you when asking your self the same question. A good person does not constantly try to push their beliefs onto others... So are you a good person when you can't even do a simple repair video witout pushing your gospel and implying that christians are better persons than non christians..? Religion is like a penis. It's nice to have one and fine to be proud of. But if you whip it out in public or try to trick people to think it's something else to get it down their throat, then it's not a nice thing you should be proud of anymore. I'm quite sure you would understand this peoblem perfectly yourself too, if people of other religions or atheists a.s.o. tried to push their beliefs/lack of beliefs down your throat and tried to convert you in every non related situation, and talked to you like they were inferiar to you because you don't have the same beliefs as them, woud you not..? Pluss the reality of the matter is that this way of talking to people have zero to non chanse of converting anybody to your beliefs either. All it will do is give you a halleluja fron the other people who belive the same thing as you allready, so if you kept this gospel preacing to your self and in that cirkle and in this pure form instead of sticking it into everything else and pushing it on everyone else, you would achive the exact same thing and get the exsact same result, only witout insulting and talking down to everyone else. So your church, your congregation, og yust dedicated videoes here on youtube would be a great place for that, just say'n.. I can't imagine you have to be rude and desiteful to other people of other faith to be a good christian.. But if you do it's not a good religion is it..?? At least you could put a warning in the title of the video so the people who just want to see a repair video could choose to scroll past to a video without the gospel pushing.. People who are interested and curious about it can and will seek it up themselves, because it's not like anybody you have the possibility to reach here never have heard about christianity anyway, it's not a state seceret you know. Peace
Thank you for great repair ideas really appreciate a man not ashamed of our Lord!
Didn’t know I needed the Bible study class but I appreciate you throwing it in here. Just bought a boat and need to do the power trim. Hope it as east as you made it seem.
Best rebuild video ever ! Thank you !!
Very Helpful Video--Thanks a Bunch and yes we All Need to Know our Eternal Destination when this Earthly Life is Over!!!
This video was the most informative with great pictures and useful information mine worked out great thanks.
Bravo!! so glad to see people like yourself give glory to the Lord. God bless you
Great & helpful video & God Bless for spreading the Gospel with it.
Great video and great witness. God bless you brother.
I got a wrench for my angle grinder that fits it perfectly mine bleeds down when sitting thanks for the videos great info keep it up 👍
Was going to buy a tool but let me check my grinder wrench to see if it fits, thanks for the idea
that was great at anybodies standards. hope everyone paid attention
You my brother, are an inspiring example of a witness! The repair info was good, but the witness was much, much better. I pray someone is touched as a result of your faithfulness. I have an ‘87 Johnson 150 and my trim solenoids keep burning out, about once a year? Any thoughts?
Hi Jim, Thanks for the word of encouragement. I just past 1 million people who have watched these videos and it is still growing. As for the trim cylinders, if you keep replacing the seals and they start leaking again in a year, any chance the shaft might have any damage on it that could be cutting into the seals?
thankyou and god bless
I used my angle grinder Spaniard wrench and it fit perfect to tighten it up
you got really lucky
@@mikeboston421 why did he get luck ?
@@manmanman6956 because most angle grinder spanner wrenches won't fit.
@@bradhawkins3687 i've used snap ring pliers with the 90 degree ends as well. works perfectly. you dont need a ton of torque to seat that seal. little gasket sealer on it is all you need.
Excellent Video.
Great video. Thanks for posting.
Thanks for watching!
Awesome vid thanks for posting it!
Seems like you might have room to replace the motor too. Thanks for sharing.
My Tilt/trim constantly needs oil but I don’t see it leaking on ground. Loss is during run time. Should I replace all piston seals?
Look at the top of the piston seals and see if any of them look oily. Fluid loss probably wouldn't show up on the ground.
thats the MUCH better fastrack system. just 2 pins instead of 6 seized screws to get the thing out. plus once its off you can replace the trim motor as they all go bad eventually.
Thanks for the comment. I like you suggestion just in these salt water areas were we are located the lower pin is many times no longer removable due to salt intrusion.
@@creativerepairing2960 you got it. Some are a nightmare... especially the big v6 motors as you have alot of weight on it. Relieving the pressure helps, but not by much!
I have a 2005 ETEC 50. We need to replace the O ring on the hydraulic tilt pump but we cannot get the PIN out to tilt the motor up and away to get at the O ring placement. The pin is threaded on the starboard side and we have attempted to slide hammer it out. We were warned that hammering on the pin on the Port side would cause it to mushroom and make things work. Any Ideas?
I am sorry I am not familiar with that model.
you don't need to take the pin out just to trim the motor up! unscrew the manual release on the port side 1/4 turn or so, and lift the motor up. put a block under it to keep it up, or use the trailer lock. then complete your work.
@@ct1762 I did the smart thing, took it to the local shop with 3o years of experience, and had them fix it right.
@@victordohleman953 very smart! Lots of guys have pride problems, but taking it to someone thats done this exact thing 200x is just common sense
great and helpful video thank you
Glad it was helpful!
Great video on replacing the tilt seals, I have a leak in the tilt as well but dnt want to buy the whole kit ($80). Do you know the part number for just replacing the seal for the tilt.
No, but there are several web sites which have parts schematic diagrams where I am sure you could find it. Thanks for the comment.
take it apart, take in the old seal, best if you take in the old trim part that has the seal on it to make sure it fits right
Go to Evinrude dot com get the oem part number then go to eBay search that number with Evinrude and part number and you’ll get oem available parts and aftermarket Igot oem seals and tool to do the job and oem service manual not clymer or any other manual JT 🇺🇸🇺🇸🐟🐠🐠🎣🐟🎣🛥🌴⛱😊😊🙏🏻🙏🏻🙏🏻
He made the video because he is a Christian. Took time out of his busy schedule to try to SAVE your no trim cylinder build SELF . And maybe u should know Christ then you wouldn't have to watch this video because all WISDOM COMES FROM ABOVE !!!!! PRAISE THE LORD JESUS CHRIST!!!
Was you tilt motor making any weird noises before you changed the seal?
Minen has bad seals and has recently started to sound weird.
Will be attempting this soon. Thank you for this video!
Hi, Thanks for the response. It didn't make any weird noises just was leaking trim fluid at the base of the shaft. The trick to this video is realizing you can rebuild it without taking the whole trim system out of the saddle. Best of luck on you job. Thanks
I have a jhonson 1988 motor. How to find out which trim motor to get
go online to CrowleyMarine.com and enter your model number and get to their schematic drawings which list part numbers. From there whether you buy from them or not you can use the part number to search places such as ebay or other platforms.
@@creativerepairing2960 thank you
The part with the nut and was hard to get off, had to use a bearing puller after I removed the nut. Trying to put it back it very snug and can’t get it back on. Any ideas?
Hi Johnny, Sorry to hear about your problem. Sorry I don't have any ideas for you on that one.
Hi my name is Marco from germany. I have a problem with my E175FSXECS, especially the part 0435263. I dont know wich way i have to put the springs with the balls and these little metal pin together, cause i lost them during my repair work. Do you have a precise description? It would be help me so much. Best regards from germany!
Hi Marco, I couldn't give you an exact answer without taking it apart again. I would suggest you try one of the parts schematic diagrams. I usually use www.crowleymarine.com. Hope this helps you.
Americans do have the right to free speech, he expressed his beliefs and you expressed yours. Your peace comment came after a venting diatribe
“Peace”
Mine is a 1984 115 hp evinrude and the only way to get to heaven is through Jesus Christ stay safe
It's the same with a 78 140
That shaft can be engineered. Look for a chrome company that does re chroming. They can do it
Where do I get the tool and the seals kit?
I got the seal kit off ebay. The tool also came from ebay but was a used OEM tool. Try searching the internet for "spanner wrench" and you will see some options. If you have a freshwater engine some of the cheap universal spanner tools will likely work. My engine is a lower saltwater use and the top came off the cylinder very easy.
why dont you flip down the thing that holds up the motor
FBI !!!!! NICE !!¡!!!
I did not know this was a Bible study video..just wanted to see the fix not a lecture on Christ..
I'm a Christian, I was thinking the same thing but you can always just fast forward like I did.
@@Berkner80 I did but it is a pain when everytime you stop you still here about jesus and not what the video is describing half the video was religious mumbo jumbo
@@donkeypunchout I don't disagree.
I don't agree with mixing instructional videos with religious beliefs. It's definitely poor form. I'm sure the Christians would comment about a mechanical video that had a Satanic commercial in the middle. Maybe you should place it at the end so that you don't offend people that are looking for help with there motor. Just start a Christian channel and help people without Jesus, I think he would agree.
In the Trying Times we are Living in, it would be a Shame not to have God on your Side as Tomorrow is not Promised to Anyone, we are All One Heartbeat away from Eternity--Heaven has a Great Air Conditioning System--Hell is Burning Hot and its Forever without one Drop of Water to Quince your Thirst!!!
Pretty good video. Skipped past the religious speech.
Could do without the bloody sermon!
Can't you christians do anything without preaching the gospel..??
It's a shame, because the "How to/repair" part is actually quite good.
But since you ask "Are you a good person?", here is a little hint for you when asking your self the same question.
A good person does not constantly try to push their beliefs onto others...
So are you a good person when you can't even do a simple repair video witout pushing your gospel and implying that christians are better persons than non christians..?
Religion is like a penis. It's nice to have one and fine to be proud of.
But if you whip it out in public or try to trick people to think it's something else to get it down their throat, then it's not a nice thing you should be proud of anymore.
I'm quite sure you would understand this peoblem perfectly yourself too, if people of other religions or atheists a.s.o. tried to push their beliefs/lack of beliefs down your throat and tried to convert you in every non related situation, and talked to you like they were inferiar to you because you don't have the same beliefs as them, woud you not..?
Pluss the reality of the matter is that this way of talking to people have zero to non chanse of converting anybody to your beliefs either.
All it will do is give you a halleluja fron the other people who belive the same thing as you allready, so if you kept this gospel preacing to your self and in that cirkle and in this pure form instead of sticking it into everything else and pushing it on everyone else, you would achive the exact same thing and get the exsact same result, only witout insulting and talking down to everyone else.
So your church, your congregation, og yust dedicated videoes here on youtube would be a great place for that, just say'n..
I can't imagine you have to be rude and desiteful to other people of other faith to be a good christian..
But if you do it's not a good religion is it..??
At least you could put a warning in the title of the video so the people who just want to see a repair video could choose to scroll past to a video without the gospel pushing..
People who are interested and curious about it can and will seek it up themselves, because it's not like anybody you have the possibility to reach here never have heard about christianity anyway, it's not a state seceret you know.
Peace
My sentiments exactly, well said @stiantiger.