How to replace a kitchen tap - monobloc kitchen mixer tap
HTML-код
- Опубликовано: 21 сен 2022
- This video shows how to replace a kitchen tap - monobloc kitchen mixer tap. If you'd like to support the channel please like and subscribe. The equipment used in the video is listed below with links.
Disclaimer These videos are presented as information videos, they are not instructional videos, and are not intended to instruct you or others to undertake specific procedures. As such, myself, my channel or any persons featured on the channel are not held responsible for any damage, loss, injury, or death as a result of you watching these videos and following specific actions. We are all responsible for ourselves, our decisions and any actions we take.
Equipment used in the video is listed below:
1. Kitchen Tap - Cooke and Lewis Double Lever Mono Mixer Kitchen Tap Chrome amzn.to/3JV6hJb (this is featured in video) or cheaper alternative Hapilife Kitchen Sink Mixer Taps Monobloc Dual Lever Chrome Brass amzn.to/3zhdCOu
2. Screw driver set - Bosch 91pc. V-Line Titanium Drill and Screwdriver Bit Set amzn.to/3lQu8St
3. Box Spanners - Monument 3240 3240U Mono Tap Back Nut Spanner Set with T-Bar. amzn.to/3JWjamv
4. Spanner set - Silverline 380681 Open Ended Spanner Set 12pce 6 - 32 mm amzn.to/3ZnXkOw
*Disclaimer: The equipment list above contains affiliate links, which means that if you click on one of the product links and purchase a product, I may receive a small commission. This doesn’t cost you - the viewer - anything. I assure that only the tried-and-tested equipment that I regularly use, and trust are featured on the list. I refuse to list or endorse poor quality equipment, materials, and products that fail to meet my expectations. The links also aim to offer additional information about equipment and products that you might find useful.
Great thanks. It’s given me the confidence to tackle the replacement of our leaking monobloc tap 👍🏼😁
Glad it helped - good luck with the project 😊👍🏼
Thanks for the video man.
Thanks Jason - I appreciate the support 👍🏼
Great video mate explanation was brilliant and clear really helped me out with my first attempt of replacing a old mixer tap
Thanks for the support Paul - really glad it was useful for you mate 😊👍🏼
Brilliant video, thank you ! :)
Thank you for the kind words. Good luck with your project 👍🏼
Great guy great job.kindest regards tim in uk
Thanks for the kind message and support Tim - really appreciate it 😊👍🏼
perfect job
morning ,all the way from kenya nairobi.
i am really enjoying this powerful inspirational learning.
Hello Julius, thank you for your kind words - I hope that it was useful.
Nice job, going to be changing my sister in laws mono mixer so thank you
Thanks for the kind words. Good luck with the project - hope it all goes smoothly 👍🏼
Much easier to attach the crescent-shaped washer and plate before feeding it all through the hole from the top. The reason they are that wacky shape is to allow you to do that. Then you don't have to fiddle on defying gravity to fit them from below.
Thanks John 👍🏼
Neat job. Thanks
Thanks for watching!
I have a twin pillar taps in the kitchen and want to swap to a spring pull done mono. Will the existing pillar tap hole be wide enough to take the new tap?
My advice would be to measure the existing hole circumference, in relation to combined widths of the two flexi-tails and thread screw. There needs to be enough circumference for all three to slide through. Also ensure that the base of the new monobloc that sits on top is wider than the hole (unlikely to be a major issue as they often are). The biggest issue is likely the fact you’ll be changing from two holes to one, so you should think about how you’ll cover the other hole. I hope that this helps. 👍🏼
@@makeitwork-propertydiy10yes thank you for taking the time to answer.