OSPF Routing Protocol using Cisco Packet Tracer

This video explains step by step procedure of how to Configure Open shortest path First(OSPF) routing protocol which is internal (Intra-domain) routing protocol using cisco packet tracer

[@galaxytoras5439]

Ssit students attendence -->

[@esportsgaming2297]

I'm very happy by seeing your vedios of Cisco packet tracer mam because ours lecturers wont explain good like u that u explain . Thanku mam for good preparation for exams

[@DileepKumarMB]

Nice explanation... Good introduction to ospf using "Cisco packet tracer".

[@ssmarcosvinicius]

thanks!! you saved my life and dignity!!! Love u

[@fizaansari489]

Thank you so much...You made it very easy.

[@sakshijaiswal1108]

wonderfully explained mam! thankyou!!

[@josephjaybarrera755]

this lady is legit, listen to her

[@tomas2033]

Thanks for your effort of helping us

[@ferenccziryek3642]

hi thank you, should I give static route? ping itt does not reach from pca to pcb only def. gateway.

[@mdmahfuz8771]

Thank you so much for beautiful exaplannation, it was very helpfull.😃😃😃

[@mohdyusufkhan8214]

Very well explained. Finally understood ospf

[@educationsingh2038]

Are u Run the network on software ? 😂😂

[@mohdyusufkhan8214]

@@educationsingh2038 I don't know if you were attempting to roast me, but I didn't understand shit cuz my english ain't that bad brother. Do better.

[@sreeharivs95]

Great explanation for the practicals . Just a doubt does ospf really care about the number of routers or the cumulative interface cost

[@shazii0852]

Bundle of Thanks mam❤

[@arvindkumargiri8815]

Superb explanation

[@mahuubao]

Excellent ... well done ...

[@microsoftsarker]

This is a great video,

[@joelkazhila1636]

You are the best madam ❤️❣️🤝🤝🤝

[@educationsingh2038]

Their are ,3 modes in CLI and all this commands doing in 3rd mode , for doing first enter en( enable ) it set u in 2 nd mode after config ( configuration) u enter in 3 rd mode . This ospf protocol command done in 3rd mode of router . Thanks u

[@manuelmilla4399]

in router configuration in packet tracer 6.2 I have an error in CLI. It can be solved typing
enable
configure terminal

[@venkatagopivuggam9335]

Hii mam I have some questions about framerelay eigrp ospfipv6 etc could you explain it please respond

[@ind8844]

Excellent MAM. 🌹

[@saadabdillahiali6545]

nice explanation but I could not send from ROUTER2 to PC1 could you explain me plese ?

[@mihirsavla]

Best explanation

[@manuelmilla4399]

bravo! very good explanation about how to set up a network inside an autonomous system

[@muthulakshmip4997]

thank you professor

[@minakshibalaram6054]

Please clarify the use of Product Id number and area number and when it change?

[@e.aabusafieh6951]

thank you very much

[@almconstructions6165]

NICE!!! 👍

[@samiullah-we3qk]

THANK YOU

[@Luisdany05]

thank you

[@captainjacksparrow8916]

thank you maam

[@MyMadspirit]

What does area0 mean?

[@hermanchan4424]

nice

[@fayazmohammad1391]

TQSM madam

[@sahilanand30]

Thanks mam

[@creatorz6739]

thank u

[@chiblackjesus]

I'll see you in heaven 😂♥️

[@ashishgudhekar3045]

thank

[@tanishkaachaturvedi2173]

thankyou thankyou thankyouuuuuuu

[@kelless1842]

It’s very lengthy process and I know the shortcut

[@addy_foxer6475]

Area0?

[@amitajaiswal1580]

Showing in CLI invalid input detected at '^' marker while writing networks. Why?

[@ao3188]

in which mode you are

[@ao3188]

config mode?

[@manuelmilla4399]

enable
configure terminal

[@ferenccziryek3642]

ok I put a third pc too

[@notasongapart]

You could have used RIP instead of CLI, that would have been easier.
But Thanks for you efforts, you helped us a lot

[@TheDJSyaheer]

But then you would not be using OSPF routing protocol but RIP instead.