Thank you for your clear building, i flew rc planes 20 years ago, but now im overwelmed by all the terms and print plates.. I bought the same as in this video serie "stack",so glad to see someone explain this mountain of electrics..all these connections pfff I hope it will work, and fly.. Since there are no big open areas here in the hague the netherlands anymore where we use to fly, its not easy to connect in real, to see it in real.. So thank you again!
Thanks for pointing that out!! I reviewed the video and at that point I had already finished soldering. Looks like it's a piece of plastic that fell out of the Vifly shortsaver 2 packaging when I took it out. You can see this at 35:20 onwards. Good catch though and I should have made sure there was no debris before testing it. Cheers! 👍
it looks like the chips near that battery terminal got crazy hot during this process. I am always a bit worried about this step and I tend to limit the contact time to 3-4 seconds at the max, at 400 deg C
I bought the same quad but it didnt include any manual so i watched your video. It was veryy helpful. I’ve got 30A esc. Which capacitor that i need it for better noise filtering? How much volts and farad?
Hi,is this Ready To Sky brand Mark4 5 inch FPV drone frame kit can fit these following components (1) RS2205 pro brushless motors (2) 20mm to 20mm M2 or M3 screw can mount flight controller stack(I bought the HGLRC zeus F728 stack so it can fit to this frame perfectly??) (3) 14mm to 14mm or 19mm to 19mm width has FPV camera (I bought the caddx ANT 1200TVL FPV camera) (4) 5045 propellers as I mentioned these components can fit to this Ready To Sky brand Mark4 5 inch frame kit ?? Please reply to this question as soon as possible
Hi.I bought flight controller stack mounting by 20mm to 20mm screw by M3 type of screw, hence I bought flight controller stack can only fit by M3 type of screws,I measured the Ready To Sky brand Mark4 5 inch frame has small size of 20mm to 20mm holes to install the stack but I bought stack can only Mount by M3 type of screws so please tell me what I do for to get M3 type of screws holes to 20mm to 20mm mounting holes? please reply to these questions as soon as possible.
I was learned at ABB construction dat a 3 phase motor got indeed pulses, but say 12 o'clock, 4 and 8. Than it does matter wich one is 1,2,3.. otherwise it would be like 12,8,4 and the push is out of balance??
These motors do operate with the phases as you mention, but it doesn't matter so much in building the drone. The software in ESC handles all of this. I hope I understood your question and the answer makes sense
It's a great hobby. Plenty of tutorials on RUclips that has helped me build my own and be able to make my own videos too! Happy to help if you have any questions.
I don't pay attention to the C ratings that the manufacturer put on the label. I go by reputation of brand and reviews of others. I haven't had any issues with GNB, CNHL or Tattu branded LIPOs.
![☀ Дикий дальнолет на 18650 Li-Ion + обзор Ferrari [Mark4 Endurance Test]](/img/1.gif)
Thank you for your clear building, i flew rc planes 20 years ago, but now im overwelmed by all the terms and print plates..
I bought the same as in this video serie "stack",so glad to see someone explain this mountain of electrics..all these connections pfff
I hope it will work, and fly..
Since there are no big open areas here in the hague the netherlands anymore where we use to fly, its not easy to connect in real, to see it in real..
So thank you again!
There was one big piece of solder debris sitting on one of the ESC chips when you tested it!
Thanks for pointing that out!! I reviewed the video and at that point I had already finished soldering. Looks like it's a piece of plastic that fell out of the Vifly shortsaver 2 packaging when I took it out. You can see this at 35:20 onwards. Good catch though and I should have made sure there was no debris before testing it. Cheers! 👍
This is amazing. Thanks so much for the content!!!
it looks like the chips near that battery terminal got crazy hot during this process. I am always a bit worried about this step and I tend to limit the contact time to 3-4 seconds at the max, at 400 deg C
looks like every iron is different, when I set my soldering iron to 400degC it burns everything around ;)
I bought the same quad but it didnt include any manual so i watched your video. It was veryy helpful. I’ve got 30A esc. Which capacitor that i need it for better noise filtering? How much volts and farad?
Apologies for late response. I use 35v 560uf Low ESR capacitors.
Hi,is this Ready To Sky brand Mark4 5 inch FPV drone frame kit can fit these following components
(1) RS2205 pro brushless motors
(2) 20mm to 20mm M2 or M3 screw can mount flight controller stack(I bought the HGLRC zeus F728 stack so it can fit to this frame perfectly??)
(3) 14mm to 14mm or 19mm to 19mm width has FPV camera (I bought the caddx ANT 1200TVL FPV camera)
(4) 5045 propellers
as I mentioned these components can fit to this Ready To Sky brand Mark4 5 inch frame kit ??
Please reply to this question as soon as possible
19x19 camera. Yes it will fly ok
Hi.I bought flight controller stack mounting by 20mm to 20mm screw by M3 type of screw, hence I bought flight controller stack can only fit by M3 type of screws,I measured the Ready To Sky brand Mark4 5 inch frame has small size of 20mm to 20mm holes to install the stack but I bought stack can only Mount by M3 type of screws so please tell me what I do for to get M3 type of screws holes to 20mm to 20mm mounting holes?
please reply to these questions as soon as possible.
I was learned at ABB construction dat a 3 phase motor got indeed pulses, but say 12 o'clock, 4 and 8.
Than it does matter wich one is 1,2,3.. otherwise it would be like 12,8,4 and the push is out of balance??
These motors do operate with the phases as you mention, but it doesn't matter so much in building the drone. The software in ESC handles all of this. I hope I understood your question and the answer makes sense
Nice. I would like to learn how to build a quad.
It's a great hobby. Plenty of tutorials on RUclips that has helped me build my own and be able to make my own videos too! Happy to help if you have any questions.
@@nxp200 thanks. Now I am confident to buy the parts, and watch your videos to build my first built. So far I am buying BNF or PNP quads.
Nice man. Can this frame take 51XX props, or is it limited to 50XX?
This frame takes 51XX props. I've got iFlight Nazgul 5140 and also Gemfan Flash 5149 that both fit and work great with this frame.
@@nxp200 Thx for quick reply!
do i really have to get a 100 c rate battery ??
I don't pay attention to the C ratings that the manufacturer put on the label. I go by reputation of brand and reviews of others. I haven't had any issues with GNB, CNHL or Tattu branded LIPOs.
ok that was very helpful thank
you very mush@@nxp200
can i fit APM controller
on mark4 frame ?
Sorry. I have not used APM controllers or Ardupilot before.
is there an all in one esc for the dji naza?
It has that in Speedybee