good job on cart build. would have been a better vid if you'd left the music out so we could have heard the symphony played by the engine in 4-cycle time.
Hey I REALLY need some help. Where/how did you hook up the vacuum/pulse line for the pulse fuel pump?? I can't seem to find a vacuum port on my engine so I can hook up my fuel pump and I dont know what to do!
the front brakes are drum and the rear is disc. the front drum brakes are not good, that is why are see shifter karts running disc in the front. the brakes were on the frame when i got it. just run with a brake, you don't really need a front brake unless you are planning to go high top speeds.
Hate that shifter set up and the motor jammed against the drivers seat. Guarantee someone burns themselves. Oh yeah, I agree with everyone else, that music truly bites. Why oh why do people feel they just have to add music to every video?
Nice Fellow why oh why do people think commenting there opinions on someone else’s work makes them think they could do it better? bitch go do it better
For someone that cant even spell believe right, I don't think you would even understand the difference between a 2 stroke racing kart and 4 stroke homemade kart. Well if you want the straight answer there's a big difference.
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
so you just drilled a hole in the intake manifold and you got a pulse. Thanks a lot that really helped i honestly had no clue where to attatch the pulse line to. Also I was thinking before if i could use the engine's vent line for a pulse or is that too much pressure.
Luke DaLegend they sell manifolds with a nipple attached . That's what you want . And the engine vent is not enough pressure, I tried that lol . The I tie is the prefect spot,
Music killed the vid for sure
I’m about to put one of those engines in a mini bike we’ll see how it goes lmao
That handbrake is SICK
Seems like the dislike made the video sound better 👍
Brooooo tht shit is dope asf !!!
Dang i wanted to hear that engine the music covered it
You have a plan to build the chassis of GO KART
Cool kart, could care less for the shitty music! Why not just let us hear the kart?
Might wanna richen up the jetting a bit. Otherwise great build!
Ya im sure were not the only ones i cant get through it
Better to have a rear-mid engine.
That's crazy because every pro kart in the past 30 years or so are just like his! Weight transfer within a short wheelbase is the goal
someone is selling a 2 stroke offroad stick shift 4 speed go kart and he claims it has a top speed of 50-60 mph, it looks like a steal for 550
music stinks. would've been better to listen to the 4-cycle 200cc symphony produced by the engine. nice build.
good job on cart build. would have been a better vid if you'd left the music out so we could have heard the symphony played by the engine in 4-cycle time.
Nice build! Where can I find a steering wheel like that for mine? Thanks
Preston Holt on eBay . It's called a butterfly go kart steering wheel
Brz Rage Alright thank you
Don't complain about the music. Just mute the video. Don't whine about it. It's a damn sick build and a great video.
Hey I REALLY need some help. Where/how did you hook up the vacuum/pulse line for the pulse fuel pump?? I can't seem to find a vacuum port on my engine so I can hook up my fuel pump and I dont know what to do!
Peter Armour I used the intake manifold. I drilled and tapped a nipple . You can get the pulse from there
Isn't the intake manifold rubber though? How does a fitting stay in there?
Peter Armour I drilled and tapped it . Or you can buy intake manifolds with the fitting on it already
Alright great. I have a fitting for the intake manifold already, but wasn't sure if it would get enough vacuum that way
Peter Armour yeah you get good pulse from there . And you need the manifold to be aluminum
Where did you get your rear wheel hubs or what brand or company are they are did you get them from?
Hey I have a lifan 200 cc engine is that what you were using here
how did you install the floor plate? welded them? or how?
sick bro! do more vids on that!
I would like to buy it from you man
what is length width and height of the engine
This sterling wheel is a big shit !
Big enough gas tank??😂😂😂
Would like to buy it from you
Wy do people take the time to build karts with these junk engines on them. Get a used dirt bike engine that makes some real HP.
because they are cheap and dirt bike engines are hard to come by
I have a honda nighthawk twin 5 speed street bike motor on My shifter kart...check out the video👍
Great work bro keep it going
where can i get some tiers
Hey what was the exhaust you used, and is there a good video/place to find out how to set up the engine properly.
Thanks
It's a 250cc Honda manual engine
It's the stock exhaust. I just cut the muffler and welded a straight pipe . I just looked up wiring diagrams to figure it out :/
Do you know where to get a cheap wiring harness for the engine?
Luke DaLegend the best place would be eBay
top speed?
Badass😎
Are the front brakes disc or drum hydraulic ??? what make and where from thanks
Musicjunkie1933 the front brakes are drum
Trying to figure them out i can find disc hydraulic but not drum what make modal more info on front brakes please ???Thanks
the front brakes are drum and the rear is disc. the front drum brakes are not good, that is why are see shifter karts running disc in the front. the brakes were on the frame when i got it. just run with a brake, you don't really need a front brake unless you are planning to go high top speeds.
I wanted them to lock front wheel to do burn outs disk are to big to fit under body like said doing gas powered mobility scooter thanks
Hate that shifter set up and the motor jammed against the drivers seat. Guarantee someone burns themselves. Oh yeah, I agree with everyone else, that music truly bites. Why oh why do people feel they just have to add music to every video?
Nice Fellow why oh why do people think commenting there opinions on someone else’s work makes them think they could do it better? bitch go do it better
I dont really belive its a 200 its WAY TOO SLOW
For someone that cant even spell believe right, I don't think you would even understand the difference between a 2 stroke racing kart and 4 stroke homemade kart. Well if you want the straight answer there's a big difference.
Xeno Haha Good one And i know All About it You wanna race wenever let me know
Yeah well my cr125 2003 kart would kill that just saying.
Why did you not set the pedals further from you? You can clearly see you can stretch your feet 1 centimeters more 2:13
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
Mosquito they were actually I bit too far from me , I wanted to move them closer too me Bc when I push the gas all the way down I had to stretch my foot a lot . I just left it tho. It was not too bad
ok i see
What type of motor did you put on it where did you find it
A 200cc 4 stroke 5 speed manual I got it off eBay , it's a Chinese motor
The Lifan engine?
Brz Rage need link to engine!!!
How did you set up your fuel pump system?
Luke DaLegend i used the tank on the side and a diaphragmic fuel pump , I got the pulse from the intake manifold
so you just drilled a hole in the intake manifold and you got a pulse. Thanks a lot that really helped i honestly had no clue where to attatch the pulse line to. Also I was thinking before if i could use the engine's vent line for a pulse or is that too much pressure.
Luke DaLegend they sell manifolds with a nipple attached . That's what you want . And the engine vent is not enough pressure, I tried that lol . The I tie is the prefect spot,
Brz Rage alright man thx a lot
Luke DaLegend no problem man
you don't need a link to that shit noise