TIMING MARKS AND TIMING CHAIN INSTALLATION ON MAZDA 2.3 CX-7 CX7 MAZDASPEED3 MAZDASPEED 6
HTML-код
- Опубликовано: 6 фев 2020
- TIMING MARKS AND TIMING CHAIN INSTALLATION ON MAZDA 2.3 CX-7 CX7 MAZDASPEED3 MAZDASPEED 6
In this video we will explain the timing marks and timing chain installation procedure on Mazda with 2.3 Turbo Engine. We have the complete video that explains how to remove the timing chain in order to replace it. We explained the timing marks and timing chain installation procedure on Mazda CX-7 but it should work on MazdaSpeed 3 and Mazda speed 6 with the 2.3 turbo disi engine since they all share the same engine.
This video may be helpful on:
Mazdaspeed 3 2.3 Timing Marks, Timing Chain Installation Replacement
Mazdaspeed 6 2.3 Timing Marks, Timing Chain Installation Replacement
Mazda CX-7 CX7 2.3 Timing Marks, Timing Chain Installation Replacement
► Timing Chain Kit: amzn.to/2PMNEwd
► Timing Tool: amzn.to/2Mkt3NH
► Engine Sealant: amzn.to/2oKQOpp
► Front Crankshaft Seal: amzn.to/34MyVWg
► Screwdriver Set: amzn.to/34a6r9X
► Clip / Panel Removal Tool: amzn.to/2ZIa03I
► Tool Set: amzn.to/2n2dnpb
► Torx Socket Set: amzn.to/2oBNBZ0
► Reverse Torx Socket Set: amzn.to/2oEEYwQ
► Makita Impact: amzn.to/300c4Jt
► Dewalt Air Compressor: amzn.to/2nVApOq
► Impact Wrench: amzn.to/2nVAOjU
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmech...
► Our Website: mechaniclifestyle.com
► Our Baby Girl Channel: goo.gl/WiVs8Y
► Our Second Car Channel: goo.gl/XB6fHq
► Honest Product Review Channel: goo.gl/sMPQXk
► GoFundMe Link: goo.gl/pUife3
Our Most Popular Videos:
► Bumper Repair: goo.gl/XBe4Sh
► Missing Wheel Lock: goo.gl/5n4a5i
► Bearing Replacement: goo.gl/JSNDnZ
► Restore Headlights: goo.gl/qVhDkf
♦♦♦ Cameras & Gear Used For This Video ♦♦♦
•Cameras
Panasonic Lumix FZ300: amzn.to/2BNWtNA
•Tripod
Polaroid 72-inch: amzn.to/2iVTmP4
•Microphone
Polaroid Pro Video Condenser: amzn.to/2krpSsA
•Light
NEEWER 160 LED CN-160 Dimmable: amzn.to/2jjg9Bd
•Comuter for editting
Lenovo ideapad 310: amzn.to/2kqUNFl
♦♦♦ Other Equipment and Gear that I use ♦♦♦
•Camera
Sony HD Video Recording HDRCX405: amzn.to/2jk8nqB
•GoPro HERO5 Black: amzn.to/2ktNKfj
•Extra Computer For Editting
Lenovo Ideapad 510: amzn.to/2ktOuB7
► Like Us on FACEBOOK: / worldmechanicsofficial...
► LIKE & SUBSCRIBE for MORE DIY VIDEOS that could SAVE YOU BIG $$$$$$$ !!!
This is not a sponsored video. Everything is purchased by us!
The video is meant for entertainment purposes only. Do not Attempt!
AMAZON ASSOCIATES DISCLOSURE
Auto Repair Guys is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com
*Disclaimer
We, Auto Repair Guys, are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not Auto Repair Guys. 
Авто/Мото
⛐ Check out our Garage to see what tools we use and recommend:
www.amazon.com/shop/worldmechanics
⛐ Subscribe and hit the notification bell by the subscribe button for new videos: ruclips.net/user/AutoRepairGuys
⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
I have done the timing on cx-7 couple of times with no problem ,. Now I am doing it again and wherever I do I can't get it wright.
All the timing tools were installed correctly, the pin down by the crank shaft and the locking tool for the cams.
It will always pop the p0012.
New chain and tensioner , new gear , oil control valve and all that .Head been to machine shop too.
Now the good stuff...... The small filter in the cam cap was checked and it's clean , the cam cap was leaking pressure so the machineshop guys resurfaced for me + they apply some aluminium to aluminium compound for extra seal - still no luck.
I even used a different timing tool that fit rely tight , because I learn not to trust these Chinese tools where you can get a lack between the tool and the cams, so after all that p0012 is still breading down my neck.
Engine will fire wright up but I can feel slow response on the idle when hit the gas paddle also has lack of power like is off timing.
Sooo.... it has been a lot fun working on this vehicle , if someone can come up with any ideas will be greatly appreciated.
Thanks.
I'm having the exact same problem. I have done all the stuff you have. I even replaced ALL of the timing parts, cam gears, vvt, chain, guides, tensioner, even the ocv, and cam position sensor. Still p0012. If you have anymore info I would love it. I have been fighting this for 3 months now
Hello, do you fixed the problem?
Excellent, your show is one of my favourites
Thanks and keep up the Good Work Guys.
Hey, not sure if i missed it in the video or not, but friction washers should be replaced everytime the are decompressed. Also, anytime your applying pressure to the crank to loosen or tighten bolts with the chain on be very careful, the cam at the end with the plate in it can snap other wise good video!!
Same for bolts
much appreciated!
Thanks for the video 👍
Nice....very helpful and clear.
Thanks for this video
One important step you did not change the friction washers which MUST BECHANGED when the bolt is removed ( also the bolt must be replaced also)
i just got a 07 cx7 im glad to see so many videos about it thx!
who makes the best timming kit?
Does the oil pump chain need to be replaced in order to change the timing chain?
Thanks for your videos, very helpful.
Refreshing to see guide videos made by people that AREN'T trying to be YT 'Stars', just good honest advice, well presented, well explained.
One question on this one;
The Crank Position Sensor has slotted mounting holes, how is it positioned correctly in relation to the Pulley (Harmonic Balancer)?
But this information is Absolutely WRONG !!
Hello! Is it the same procedure on Mazda 6 2.2d 2009 (Euro modell - Left steering) ??
Let me be more precise 4 cylinder number 1 lobes on my cams the exhaust would be at I'd say 7 p.m. and the intake was around 5 p.m. clockwise if you will I'm not sure if that would be the correct positions or not when I got the vehicle it did run in drive but it has a slight rough idle to it
Hey can you make a video on where all the plugs go on the top of the engine ,car was sent in for repairs and the guy never finished the job if been looking on your videos got most of them plugged in but there is still some not plugged in the car is running but the revs are hanging at 2000 rpm and if you know the colour of the wires on the heat gauge
Does the oil pump need to be timed ? As mine has had a full re build just wanted to make sure it has or hasn't have to be set thank you.
No
I skipped using the 2.3 timing componets and went with the 2.5 instead the fewl ao much tougher!!!! Specially for a turbo aplication .... this was engineered for disaster !!!!
Bro fcar f7s-g best tool?
Or not good tell me
Where you get the purple bold?
Mine has a stuck variator...but.thanks Ford for getting rid of those pesky key ways...too many decades of quality and ease of replacement... apparently
I already see BIG PROBLEM BOTH TIMING MARKS ARE not aligned most LIKLEY THE VVT actuator HAS SLIPPED and needs replacement !
Where are the friction washers ? Under the crank and cam bolts ?
One thing I've noticed and I've got a question for you if you don't mind. The lobes on the cam are completely opposite position as to the lobes on my Cam's when they're TDC so that's probably my biggest concern as his vehicle I just bought two how to fix and sell it but I do the work myself so I kind of concerned me if the lobes are incorrect on my cams
question I changed the timing chain of a 2.3 mazda and the engine does not start what would be the problem
Check for spark gas and air if it doesn't work then check your timing marks you should probably check that first
How to start replaced engine in Mazda cx7 turbo
HOW MANY KM DID THAT CAR COVER?
i need to know the length of the timing peg, the one you put on the hole where there is a blind plug at the back of the engine block, thank u
🤦♂️🤦♂️🤦♂️
I have the same car. But it has got a rough idle. I'm from Zambia
88 inch lbs for everything except the timing gears oil pump sprocket and the 13mm bolts on the timing cover :D
Wrong.
Its the worst chain they could ever put in a turbo engine ..... the 2.5 looks right!!!
😢your kit did not have pinions...
P0016 after taming chabce
Why those mechanics wear watches during working on cars, scratches or show off have money to buy watches.
Yeah huh I stopped wearing them because I always broke the glass the second time I forgot to take it off then I just stopped wearing them all together.
Bro I remove the pully with out the tools now the car is not starting .what can I do
Check your timing your out of time
But you probably bent valves so your motor is probably shot check it and set it anyway maybe you will get lucky but ......
This engine was poorly maintained ( the oil is varnished ) which greatly effects Variable vale timing which cause poor performance on the engine
Where are the timing marks on the camshafts
There are none lol. Lobes dictate
W/o nic on Tuesday cars Mechakin
Crank mark
G6 12valve
Very Uneducated... these vehicles do not have lifters... these are Cam Buckets that are shimmed. The noise you hear is more than likely the Intake Cam Phaser. Also keep in mind these vehicles are Direct injected which you failed to mention. The fuel rail and injectors are pressurized up to 2000 psi. Did you check to see the if the injector seals. This motor is a mess and I’m sure you may mean well but educate yourself. And if you notice the oil leak more than likely is from the timing cover seeping closer to the alternator not the crank seal.
Your video is very misleading for anyone searching RUclips for help on this motor.
'Lifters' is a generic term for any type of Cam Followers, whether that's Bucket-and-Shim. or Rocker Arms.
He knows more than you do, all you do is post videos of nothing.
Nice..very helpful and clear.