Easy grape vine trellis install with T Posts

Поделиться
HTML-код
  • Опубликовано: 18 ноя 2024

Комментарии • 21

  • @pgannon1948
    @pgannon1948 2 года назад +3

    Interesting design. Sad that you didn't show us how your dead-man anchors are set.

  • @tylersadler6726
    @tylersadler6726 3 года назад +2

    Can you post a update. I'm going to do this.

  • @janicebailey1601
    @janicebailey1601 Год назад

    Are you still making the top piece supports. I am interested. I am putting new posts in for my muscadines and I have been looking for ways to do it. One other question how do the wires attach to the post below the top one. I am thinking it is just wire clips but not sure.
    Thanks!!

  • @patferguson572
    @patferguson572 3 года назад +4

    Hi Scott. I'm just about plant 2 grape vines for home garden, and want to do trellis the same as yours. How did it go? Did T posts support grown vine? Thank you.

    • @scottcunningham8038
      @scottcunningham8038  3 года назад +1

      As long as you use the dead mans as support it works fine. Also, use the turnbuckles so you can take out slack if you need to. I have had mine up for 5 years with no sag.

    • @patferguson572
      @patferguson572 3 года назад

      @@scottcunningham8038 Thank you very much. I used star-pickets [I think similar to US T-posts posts]. I put 8ft posts 2ft in the ground. Then used short star pickets angled into the ground [just leaving the top hole exposed.] Then used the trellis wire across top of picket, down to ground picket, through hole, then back up to top of post and wired securely to top wire, Then used a metal bar, put through the 2 wires and twisted them until wire tight. [Sorry for the long description - a drawing would have been better]! I hope this works. [Also, I don't know what a 'dead man' is.] Thank you again ♥

  • @haleyfink6325
    @haleyfink6325 Год назад

    Hey! Any chance you have the link for the little guide pieces?

  • @all5n
    @all5n 8 месяцев назад

    I think im just going to use an angle grinder to cut a groove in the top of the t-post instead of messing around with some little guide piece.

  • @charlesbroadway6864
    @charlesbroadway6864 2 года назад

    Could you send me the link for post guides? I can t find it.
    Denny

  • @eliotguernsey5774
    @eliotguernsey5774 2 года назад +2

    Hi Scott,
    It looks like you only used the T-post caps on the end posts. Is that correct? Or did you use them on the middle posts, too? Thanks,
    Eliot

  • @gypsyjunklady
    @gypsyjunklady Год назад

    If any part of that buckles its going to launch metal. Fast.

  • @montr2229
    @montr2229 2 года назад

    Where can I find those T post caps?
    Or anything similar

  • @Goose6287
    @Goose6287 3 года назад +1

    Can you provide any more details on your devices you made to hold wire on top of t post? I’m going to do this but wanted to see how you did it before I reinvented the wheel. Also, are 8 ft t posts necessary? I was going to go with 7

    • @scottcunningham8038
      @scottcunningham8038  3 года назад +1

      I purchased H shaped aluminum channel. Cut it to about 2 inch lengths and notched out sections to fit on top of the Tpost. 7 ft posts should work fine.

  • @Lowstarfarm
    @Lowstarfarm 5 месяцев назад

    you could probably just weld a metal ring to the top of the side of the T post .

  • @marywalsh4213
    @marywalsh4213 2 года назад

    I need the post guides

  • @kirkrowan949
    @kirkrowan949 3 года назад

    Where can I get top pieces please? Also, can I do posts 6 ft apart? I already have grapes planted.

    • @bishopcedric4395
      @bishopcedric4395 3 года назад

      i know Im kinda randomly asking but does anybody know of a good place to stream new series online?

    • @maddoxlandyn9050
      @maddoxlandyn9050 3 года назад

      @Bishop Cedric flixportal xD

    • @bishopcedric4395
      @bishopcedric4395 3 года назад

      @Maddox Landyn Thank you, I went there and it seems like a nice service :) I appreciate it !!

    • @maddoxlandyn9050
      @maddoxlandyn9050 3 года назад

      @Bishop Cedric happy to help xD