This is easily the best tutorial on this process, I watched several before I found yours and this is the only one I was able to make sense of, and follow along with!
For anyone having trouble putting the back plate on or that your K3/K4 are tight, I recommend unscrewing and re-screwing the paddle's motherboard. Try refitting it--it's probably not sitting right. That worked for me!
Man, these are nice and the price is amazing, it's just the process. And when the sticks go, you're in a pickle. The Edge is a lot of money but it seems the future proofing is worth it...
it really is super easy. It took me about 2 hours but thats because I replaced everything. Rise remap kit is an easy EASY 20-40 minute install if you dont screw around.
These are great for people with small hands. The triggers are wayyyy to sensitive and my big hands keep pressing the paddles on accident. Great product for small hands
They’ve got another model now.. the rise 4.0 kit doesn’t work with the controller I have. It’s neither a BDM-010 nor a BMD-020. Wild. Other than that the video was helpful up until the inside was updated lol.
I’m sorry but this installation is anything but easy I just did it yesterday. it’s not easy at all. It’s doable but you need to be mechanical inclined. The rubber casing on the light omfg don’t lose it.
@@CTAtechdesk Correct I never have. I can now as I was successful and will now convert my other controller soup to nuts but it wasn’t something I’d consider easy it was doable but took skill.
I watch the video and took my controller apart and look at the board to make sure what model it it does not say BDM-XXX any where on the board back side, had to lift up and it showed the BDM-020
My controller is neither 010 or 020,. The kit I got does not fit,. Even the part that goes under motherboard is too wide,. Now what do I do?? I even went to local electronics store bought another controller and it’s same as one I got with ps5 system,..
Taking the shell off, disconnecting the touch pad ribbon placing the under buttons on correctly and the rubber sheath on the light are the issues. Oh the battery plug was not fun.
Ps5 controller works but the paddles doesn’t. LED lights up and even gives the 3 blinking lights that says it has been remapped. But the buttons doesn’t work. Any suggestions?
Weird, I followed everything but my square button isn’t working, and the back piece lights up red like it should but isn’t mapping any buttons. I’ll have to see if any of the connections are loose
Great vid, think I've stuffed it though. Turned on controller and Ps opening controller.. Didn't think much of it and unplugged batt.... Completed install.... Now won't power on.
Since I installed the remap kit on my controller, when I start a game i suddenly have no input anymore. It does work perfectly when I’m in the Ps5 menu but when I’m in an app, it suddenly stops. Do you maybe have any idea why it’s like that? Maybe that other people experience same problem
At 20:32 is that gap normal between the controller 🎮 trims and the back housing case or not.? I just did my starlight blue controller and install the clicky triggers and swappable thumbsticks. Loving it so far. 😊
Hi CTA, My issue is I installed the BDM10 on the BDM20 version controller. So naturally it didn't turn on, now I replaced everything to original and it still wouldn't turn back on.. any ideas why? Also is there a way to use the BDM10 on the V2 controller? Thank you.
I followed the video step by step and now my controller won’t turn on. When I plug my controller into my ps5 through usb-c the controller lights up orange then turns back off. Any ideas what could’ve gone wrong?
Just bought this kit on Amazon and I now have a couple of concerns. The PS5 controller I currently have came with the PS5 from pre order. I thought I heard something about being able to see if it's bdm 1 or 2 by the back, without opening it, dependent on what the model code says but it's not similar to other controllers from vids I've seen. Am I going to need a newer controller? Also do you have to cut off the bdm 1 or 2 that comes with the kit, or can you just use the one you need so if you replace the controller you don't have to buy a new kit if it's not the same bdm? Finally will this kit become unusable if a new controller type comes out as replacement (like bdm 3)? I've never bought or installed a kit like this before so please excuse any ignorance I may have on the topic. Any answers to alleviate my concerns would be greatly appreciated.
On bak of your controller the model number ends with letter A it’s either a 010 or 020 if ends with a Letter W it’s Bdm-030,. From what I hav found,. Every controller I can find that’s new is BDM-030,..
lets say the time comes when you have bad stickdrift or some other issue, is it an easy unistall to be able to install the kit on to a different controller once again?
I just did this and I can not get the back cover with the k3 and k4 buttons to attach to the back of the controller. Whenever I get it attached, its so tight that you can't press any of the buttons so I'm just playing with two paddles and no cover lmao. Ordering SCUF or aim on payday
@ 7:55, where is the other end of that cable supposed to be attached? My friend took his controller apart and started to do this with a different kit and didn't finish and asked me if I would finish it for him, also the mobo doesn't have any indication whether it's 010 or 020
I have slide on circle and I tryed to relocate it to the back paddles doesn’t work. Everything else works do you know why is it because It’s originally on r3?
If any one can help, I ordered the tactile triggers face buttons and the remap kit but I don’t understand how to install both the tactile face buttons and the remap kit because they got on the same prongs. Face buttons work but remap kit turns on but has no function. Is it even possible to have both? If so what am I doing wrong
1st question how do you know if its BDM-010, 020 or 030 without cracking open the controller? 2nd question if I don't own a PS5 system and only play on pc with controller can I still remap buttons?
Hi CTA, amazing video, I followed all the steps on the videos really carefully, unfortunately fore some reason my controller doesn’t turn on, no lights, nothing, the I tried to connect it via cable to my Pc and a really dark red light turns on, once I disconnected from the cable no lights again, do u have any suggestions for this issue? Thanks in advance.
I wonder about the grip??…..Can you hold the ps5 controller after installing the rear buttons firmly like before installing, because I used to install the 3rd party rear button for my PS4 controller. It worked fine but I can’t hold the controller firmly like before otherwise my fingers would accidentally click the rear button 🤦♀️🤦♀️ So how about your Customized PS5 controller???
Oh I wish you sold just the attachment on back with 4 buttons. I have a existing mod (built in macros) but would really love yours on the back. I guess I could order one follow the traces and solder to the header but would be waste to order the kit just to use the back buttons pcb/housing. Would you be willing to sell unpopulated pcb with the buttons/and rear shell?
There are a couple of latches on the side of the circuit board that you need to release and it is easy to remove it. That's why it is so hard to remove unless you release those latches on each side of the board.
Can you turbo the buttons? Some you hold the map button and it flashes once, twice and three times. Signifying how fast the turbo button is Will this kit do that?
I applied to my ps5 controller and now it doesn’t work.The blue leds flash but don’t turn solid so I’m not able to use and pair it to my ps5 anymore.If anyone knows what could be the problem please tell me
Done everything step by step. But the end part putting the kinder egg build it yourself box compartment was a major pain. And my buttons are not clicky whatsoever not sure if this is broke or what. Not the best from them this time around I think.
I broke one of the ribbons at the bottom of the motherboard... it's the right side and I think it's a mic because the rest works perfect. Do you know of a replacement?
This is easily the best tutorial on this process, I watched several before I found yours and this is the only one I was able to make sense of, and follow along with!
Glad it helped.
@@CTAtechdesk do you know if I would still be able to change my buttons & top casing with the rise 4 installed?
For anyone having trouble putting the back plate on or that your K3/K4 are tight, I recommend unscrewing and re-screwing the paddle's motherboard. Try refitting it--it's probably not sitting right. That worked for me!
I'll try that tomorrow. I'm rocking paddles and exposed motherboard tonight 😂
Same. It wasn't working so I took it off and found I had to tuck the motherboard under the pegs and then everything worked nicely
The shortest but most easy to follow and in depth tutorial on RUclips for this product. Thanks for making this as simple as it looks when you do it!
Amazing tutorial, just followed along and it couldn’t have been easier 👌🏼👌🏼
Glad it helped!
Extremely well edited and narrated tutorial. Cheers!
Followed this to the T and installed mine with absolutely no issues. Great tutorial
Great video! I was following the instructions step by step just to realize that my controller is bdm 030 and my extremerate kit not.
Just did the same mf thing
Man, these are nice and the price is amazing, it's just the process. And when the sticks go, you're in a pickle. The Edge is a lot of money but it seems the future proofing is worth it...
Brilliant video, I’m still building the courage to take my lovely new ps5 controller apart though 😁 I’ll save this video, thanks
Genuinely great tutorial. Very quick and easy, thank you!!
Awesome video very straight forward. took me awhile to get the "cap" on with the inner buttons but loved watching this
Just used your tutorial! Stupendous work! Super simple to follow! Thank you!
Absolutely a great video and tutorial. Thanks so much for making this for all of us.
Awesome video! Made the whole process easy to do. 🎉
Thats a really nice tutorial! Thanks for the effort and please keep the good work.
it really is super easy. It took me about 2 hours but thats because I replaced everything. Rise remap kit is an easy EASY 20-40 minute install if you dont screw around.
best tutorial on youtube by far!!!
Cheers for that 👍🏻
I dunno about you guys but taking off the back cover at 3:45 was NOT easy at all for me. I made myself bleed!
Thanks for the simple thorough walk through. Works as it should. Time to k some a
Damn bro thank you😂 just order and saw their video and was like what have i done🤣🤣🤣🤣 but perfect cant wait to do it💯
Damn bro everything is done and it works but buttons doesn’t respond
Definitely takes some getting used to. Different kind of grip. This will hold me over till they release a Black DualSense Edge or Blue 🙏
Stick with it. I can’t go back to a regular controller now. Til the edge ;)
@@CTAtechdesk Shame the Edge only has the 2 Back Buttons. Already used having the 4 😅
None of my triggers or bumpers are working and the red light wont turn on for setting and I didnt get my rubberized grip
Thank you for that video, very appreciated
These are great for people with small hands. The triggers are wayyyy to sensitive and my big hands keep pressing the paddles on accident. Great product for small hands
They’ve got another model now.. the rise 4.0 kit doesn’t work with the controller I have. It’s neither a BDM-010 nor a BMD-020. Wild.
Other than that the video was helpful up until the inside was updated lol.
same
Honestly unbelievable thankyou soo much!!!
👍🏻
Outstanding!! Thank you!!
Thanks mate!! Video is awesome😀👍🔥
Super helpful. Thank you!
thank you worked amazing
I love this man
I’m sorry but this installation is anything but easy I just did it yesterday. it’s not easy at all. It’s doable but you need to be mechanical inclined. The rubber casing on the light omfg don’t lose it.
You’ve obviously never done the joycon shell replacement. In terms of mods on any controllers across all systems, this is the easy one.
@@CTAtechdesk Correct I never have. I can now as I was successful and will now convert my other controller soup to nuts but it wasn’t something I’d consider easy it was doable but took skill.
be VERY careful of the ribbon for the microphone at the bottom when pulling back the board .. it tears very easily. ask me how i know.
Oh no. You can buy replacements 👍🏻
Grasias, muy buen tutorial 👍👍
I need to tighten my screw for my back buttons but I can’t get the back piece off and I’m afraid of breaking it
Great tutorial
I watch the video and took my controller apart and look at the board to make sure what model it it does not say BDM-XXX any where on the board back side, had to lift up and it showed the BDM-020
great tutorial. best one i have seen so far. Any chance you are doing one for the clicky hair triggers as well?
At some point I will be, yes 👍🏻
good friend good content! Do you know if there is compatibility with the CFI-ZCTTW A version?
Nope won’t fit !! I’m having same problem ,.
My controller is neither 010 or 020,. The kit I got does not fit,. Even the part that goes under motherboard is too wide,. Now what do I do?? I even went to local electronics store bought another controller and it’s same as one I got with ps5 system,..
Taking the shell off, disconnecting the touch pad ribbon placing the under buttons on correctly and the rubber sheath on the light are the issues. Oh the battery plug was not fun.
Ps5 controller works but the paddles doesn’t. LED lights up and even gives the 3 blinking lights that says it has been remapped. But the buttons doesn’t work. Any suggestions?
Did you fix it?
The controller doesn't turn on anymore :/ I think the battery is no longer working. I took it apart a few times and nothing worked.
Weird, I followed everything but my square button isn’t working, and the back piece lights up red like it should but isn’t mapping any buttons. I’ll have to see if any of the connections are loose
Great video but after I was done my controller only worked in the main menu and not in game
I kid you not it took me a lil less then 3 hours and it was worth it
Hi, I have a problem, all the buttons work except for the "circle" button. Can someone help me please?
THANK YOU!!
Great vid, think I've stuffed it though. Turned on controller and Ps opening controller.. Didn't think much of it and unplugged batt.... Completed install.... Now won't power on.
Since I installed the remap kit on my controller, when I start a game i suddenly have no input anymore. It does work perfectly when I’m in the Ps5 menu but when I’m in an app, it suddenly stops. Do you maybe have any idea why it’s like that? Maybe that other people experience same problem
im getting the same thing, cant do anything at all with my controller now
Your ribbons arent in properly. Go back inside and reattach them. Should work after that.
my LED does not stay on it starts flashing when I turn it on
Thanks!
At 20:32 is that gap normal between the controller 🎮 trims and the back housing case or not.?
I just did my starlight blue controller and install the clicky triggers and swappable thumbsticks. Loving it so far. 😊
Hi I don’t have the white cables ?? What should I do
Hi CTA,
My issue is I installed the BDM10 on the BDM20 version controller.
So naturally it didn't turn on, now I replaced everything to original and it still wouldn't turn back on.. any ideas why? Also is there a way to use the BDM10 on the V2 controller?
Thank you.
Thanks for this ,although your hands are steadier than mine lol
I followed the video step by step and now my controller won’t turn on. When I plug my controller into my ps5 through usb-c the controller lights up orange then turns back off. Any ideas what could’ve gone wrong?
Same thing is happening to me right now… Have you managed to find a solution?
Mine won't turn on either
But I have the BDM 02 model
Question so say I remap the circle button and the x button. Do they still work on the Dpad if pressed?
My trigger cables do not fit my controller.
Just bought this kit on Amazon and I now have a couple of concerns. The PS5 controller I currently have came with the PS5 from pre order. I thought I heard something about being able to see if it's bdm 1 or 2 by the back, without opening it, dependent on what the model code says but it's not similar to other controllers from vids I've seen. Am I going to need a newer controller? Also do you have to cut off the bdm 1 or 2 that comes with the kit, or can you just use the one you need so if you replace the controller you don't have to buy a new kit if it's not the same bdm? Finally will this kit become unusable if a new controller type comes out as replacement (like bdm 3)? I've never bought or installed a kit like this before so please excuse any ignorance I may have on the topic. Any answers to alleviate my concerns would be greatly appreciated.
Late response but you should be okay. This company has kept both models in mind. They might have come out with a newer kit recently, but overall OKAY!
On bak of your controller the model number ends with letter A it’s either a 010 or 020 if ends with a Letter W it’s Bdm-030,. From what I hav found,. Every controller I can find that’s new is BDM-030,..
God bless you 🙏🏼
Cant get my controller to turn on now went back 3 times checked everything is plugged in controller will blink once when plugged in then does nothing
lets say the time comes when you have bad stickdrift or some other issue, is it an easy unistall to be able to install the kit on to a different controller once again?
I just did this and I can not get the back cover with the k3 and k4 buttons to attach to the back of the controller. Whenever I get it attached, its so tight that you can't press any of the buttons so I'm just playing with two paddles and no cover lmao. Ordering SCUF or aim on payday
Tuck the motherboard under the pegs and try again. That was my issue, I put it on top and screwed down
can i use these remap buttons on PC?
i completed the assembly, but when i hold pressed the button the LED didn't turn on,
please help
My motherboard doesn’t have 020 or 010, it just has a 4
I broke my controller... it doesn't turn on anymore. Any tips?
@ 7:55, where is the other end of that cable supposed to be attached? My friend took his controller apart and started to do this with a different kit and didn't finish and asked me if I would finish it for him, also the mobo doesn't have any indication whether it's 010 or 020
That’s the mic cable
Did you forgot the L3 and R3 ????
I have slide on circle and I tryed to relocate it to the back paddles doesn’t work. Everything else works do you know why is it because It’s originally on r3?
hello, is it possible to make only two buttons work? how to do it?
If any one can help, I ordered the tactile triggers face buttons and the remap kit but I don’t understand how to install both the tactile face buttons and the remap kit because they got on the same prongs. Face buttons work but remap kit turns on but has no function. Is it even possible to have both? If so what am I doing wrong
1st question how do you know if its BDM-010, 020 or 030 without cracking open the controller? 2nd question if I don't own a PS5 system and only play on pc with controller can I still remap buttons?
Hi CTA, amazing video, I followed all the steps on the videos really carefully, unfortunately fore some reason my controller doesn’t turn on, no lights, nothing, the I tried to connect it via cable to my Pc and a really dark red light turns on, once I disconnected from the cable no lights again, do u have any suggestions for this issue? Thanks in advance.
Same 😭
Same, do you have a solution?
I wonder about the grip??…..Can you hold the ps5 controller after installing the rear buttons firmly like before installing, because I used to install the 3rd party rear button for my PS4 controller. It worked fine but I can’t hold the controller firmly like before otherwise my fingers would accidentally click the rear button 🤦♀️🤦♀️
So how about your Customized PS5 controller???
Oh I wish you sold just the attachment on back with 4 buttons. I have a existing mod (built in macros) but would really love yours on the back. I guess I could order one follow the traces and solder to the header but would be waste to order the kit just to use the back buttons pcb/housing. Would you be willing to sell unpopulated pcb with the buttons/and rear shell?
Hi there. Probably best you direct those questions to extremerate themselves. I’m just here for the tutorials 👍🏻
There are a couple of latches on the side of the circuit board that you need to release and it is easy to remove it. That's why it is so hard to remove unless you release those latches on each side of the board.
Cheers. Was harder than the Rise2 mod I previously did to remove without the latches. Will add that tho the description. Thanks
I’m having an issue with mine, the l3 and r3 seem to have some delay or something what could be the cause of this?
where do you find the bdm-010 and 020 controllers. i cant find them anywhere
My rumble wires in my controller is thinner then the ones in your video. What model controller do I need?
Bit safer to take the buttons off with the plastic prying tool
Stupid question. You don’t need any thermal paste for opening up a ps5 controller like this?
It broke my controller
It only blinks for me, how to fix???
can you map the back buttons to start + select
Finished putting the controller together and it won’t even turn on, any tips?
Can you turbo the buttons?
Some you hold the map button and it flashes once, twice and three times. Signifying how fast the turbo button is
Will this kit do that?
I applied to my ps5 controller and now it doesn’t work.The blue leds flash but don’t turn solid so I’m not able to use and pair it to my ps5 anymore.If anyone knows what could be the problem please tell me
Can I pay extra rate to do it for me because I am scared that I will break my controller
Done everything step by step. But the end part putting the kinder egg build it yourself box compartment was a major pain. And my buttons are not clicky whatsoever not sure if this is broke or what. Not the best from them this time around I think.
Sounds broke. mines very clicky.
Same here. What did you do? I left mine off and just using the paddles
@@dylanthavillian4113 i have the same problem. One of the middle paddles doesnt click. I tried everything but it seems to loose
Is this also possible with the mouse clicky set? So all in one
The blue part that you describe at 5:55 doesn't appear to be on my controller? It's a Bdm-010 so should be the same as yours?
Never mind ended up breaking my controller anyway...
My controller isn’t turning on
What charging station would you recommend for a controller with this fitted. Because the standard ps5 controller Dock doesn't fit anymore?
I’m currently trying to find one. I now have to go back to using a cable til I can test alternatives.
The charging station from AimControllers fits this easily along with Xbox controllers. Very well made.
what if your comtroller say bdm 030
For the bdm 30 is it the same installation?
Has anyone had the issue with wiring the touch pad and having a pcb with different layout
What if your controller doesn't say BDM anything can it still work ?
I broke one of the ribbons at the bottom of the motherboard... it's the right side and I think it's a mic because the rest works perfect. Do you know of a replacement?
Ok, check eBay, they have replacement mic cables 👍🏻
Where did you get that magnetic mate? That would be extremely convenient for tearing down consoles.
Amazon. it’s and ifixit magnetic mat. HTH