How To Replace Rear Wheel Bearing Hub Assembly 2010-2017 Chevrolet Equinox

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/id/1ASH...
New Wheel Bearing & Hub Assembly Set from 1AAuto.com 1aau.to/ia/1ASH...
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2010-2017 Chevrolet Equinox.
This repair was done on a 2014 Chevrolet Equinox LT 2.4L Sport Utility 4-Door AWD Automatic and the process should be similar on the following vehicles:
2010 Chevrolet Equinox
2011 Chevrolet Equinox
2012 Chevrolet Equinox
2013 Chevrolet Equinox
2014 Chevrolet Equinox
2015 Chevrolet Equinox
2016 Chevrolet Equinox
2017 Chevrolet Equinox
Tools you will need:
• 13mm Socket 1aau.to/ocW/1AX...
• 14mm Socket 1aau.to/ocW/1AX...
• 15mm Socket 1aau.to/ocW/1AX...
• 22mm Socket 1aau.to/oB/1AXA...
• 36mm Socket 1aau.to/oc/1AAS...
• Socket Extensions 1aau.to/ocW/1AX...
• Copper Anti-Seize
• Wire Brush 1aau.to/oH/1AXA...
Subscribe: / @trq
Check out our playlist:
Chevy Equinox 2010-2017 2nd Gen: • Chevy Equinox 2010-201...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@SirGolfalot-]

Good video. I hope my wheel bearing comes off that easily when I have to replace it. Glad you mentioned the torque specs for all the bolts.

[@lordrichard8184]

22 mm socket lug nuts
14 mm socket
15 mm socket
36 mm socket axle nut torque to 151 lbs
13 mm socket

[@eriknetz2252]

that was a good video. neat all the details required. torque specs tool sizes. good info. good video.

[@JustAnotherDronePilot]

Man I was hoping the customer was going to ask for a brake job after seeing the condition of the rotors & pads, never mind the wheel bearing hub assembly. Great video.

[@StanZeMan]

Very good, fluent concise video and narration. Thanks!

[@stevenjames5419]

My 2012 Equinox is a front wheel drive and has no CV axle on either side. I’m a little confused on yours having axles on the rear.

[@steveperuski5547]

I had to use a torch and heat up the four bolts to get the bolts out for the bearing, it was a prick, great video thank you 😊

[@cherylallison1968]

I have a 2013 Chevrolet Equinox LS 4 Cyl 2.4L AWD it makes a loud popping buming noise from the rear only when i turn sharp left and right. What could it be? Thanks

[@krisehn1091]

Very informative thanks

[@juancamberosg.593]

Is this for a 4 wheel drive? Will the process be the same for a rear wheel drive?

[@tonybarkdull1199]

Great video. you should lube the slide bolts while you have the caliper out for even pad wear.

[@justinwatch]

1:52 Grab the rotor and it should slide right off..
And so will what's left of the parking brake shoes. 😂😂

[@stephenheyes2202]

Nice video.Just wondering what a gromit was.The speed sensor wire? Thank you for sharing

[@davidbeltran8571]

Is a torque wrench necessary

[@claudel7419]

Belle ouvrage et bien comprise cible merci

[@wayne1271]

Hello. Odd. The parts page says it’s a front wheel bearing but in the video you are tearing down the rear…..

[@TRQ]

+@wayne1271 Depending on your vehicle, the part in the vehicle will fit in the front or rear position of the vehicle.

[@jamesantonelli2580]

Those hub bolts are a lot harder to get out than they were made out to be

[@derekmoen5382]

Great video I really appreciate it!!! So you only used loctite on the brakes? What color?

[@travishopper5133]

Why did you take the caliper apart?

[@Packer1290]

Those are some rusty brake parts. I live in the rust belt and have a 2015 with 167k miles and no where near that rusty. 😅