I had this problem while washing one small rug. Normally I wash all 5 bathroom rugs at once with no problem. thank you for your help and good advice on what fabrics to wash together.
The old-fashioned washers didn't have this issue. You just throw it in and boom its done. All these new washers are to sensitive and just meant for repairs. Thanks for the great info.
I have done all the above and still get the error. I have even reset via unplug and no issue it was a perfect working for 5 years no matter the side of load now I’m having nightmare issues
Great info, thanks. The wife only had about three hand towels in there so most likely was just that there was barely any weight and led to poor distribution. Thanks again!
Awesome video man thanks. My question is, after I replace the two bearings for the drum my machine doesnt want to go into the fast spin cycle it gors clockwise and counterclockwise trying to balance load without success.i tried it with an empty drum and same problem. Could i have installed the drum wrong????? I was ultra careful putting it back together. Thanks buddy
I fill my washing machine, leaving about 4-5" between the top of the drum and the top of the dry clothes. Saves a lot of water, power, and soap. Never had the machine failed for 12 years. I'm also sure, the savings will pay for my next washing machine.
I had bearings go out on mine and grinding, then it started throwing a UE code instead of spinning so I replaced the spider and the lower/rear tub that had the bearings. I also replaced all 3 shocks. Now it stopped making the grinding sound but I'm still getting the UE error. When I took the rotor and stator out, I noticed a chunk of the magnet on the rotor had been broken out, about 1" square (2.5cm) Could that be causing the UE error or should I be looking elsewhere? It runs through the wash cycle with no problems at all, but it always gets the error code instead of the high-speed spin at the end of the cycle. (or any spin at the end of the cycle) Please help me.
Just now after UE error my washing machine 1100and 1200 spins are not working, can I correct it myself. Or can I give only spin tomorrow morning without washing? kindly suggest
Hi thanks I like your video. I need your help to trace my lg machine. My machine when I start any cycle drain moor start .. not stoping till i stop ofter one minute motor stop.please tell me whate to be problem. Thanks in advance
I recently chaned the drain pump because of the de error and it now drains properly. Since then the cycles work properly and have checked all of the balance situations as you commented on but at the end of every spin cycle I still get the UE error. I then have to run another spin cycle or 2 to finsh the load. It also seems to not get all of the soap out. Any clues. The diagnostics check out well when you press the soil spin buttons.
Hi. in my experience it is an issue with the motor if ue error persists. How long have you had your washer ? There is 10 years warranty on that direct drive motor so you could give Lg a ring and see if they can send you a new motor. If they won';t give you one for free try and change the speed sensor on the motor I did a video on how to change that as well ruclips.net/video/cMw5ro-eWZ4/видео.html
What if after doing all as directed in the video the UE code persists? The load of a heavy towel, thus very heavy when wet, will wash fine but UE code appears when tries to go into spin cycle. First load to activate the code included a medium sized blanket with the towel. Have washed these items separately & together in the past. If have gotten UE code in past went through these steps and it cleared,
WM1812CW Endless UE after replacing main bearings, water seal and spider arm. Replaced Hall sensor. Made sure all drain lines are fully open. Changed all 3 shocks. Ran machine empty (no items in washer) through rinse and spin several times. In order to eliminate a variable, I Drained residual water from bottom at pump, then continued the cycle at "MIN 10". Motor always spins slowly left and right through the balance check phase; then throws UE at "MIN 10". Can see Rotor wobble in and out about 1/8 inch when restarting after a "MIN 10" cycle stop. Have restarted cycle after MIN 10 shutdown numerous times, each time the basket is empty and the whole system is devoid of water. I do not know what sensor is dedicated to detecting a balance problem, or if not a sensor, how the motor could throw a UE. If there was a test manual, it would help. Motor stator and rotor have residual rust deposits from the leaking main bearing seal. It does not make sense to me how this residual material could affect motor, stator, rotor or sensor operation, as it was dirtier before the bearing repair and washed many cycles of clothing for months before it became obviously noisy, telling us the bearing and seal had failed. All comments appreciated, Thank you!
Hi dear, just having same problem with my washing machine. I just pause it but problem was I couldn't open the door just like on your video.. I hope you have an answer for me thanks...
OK I have one of these in the townhouse that I rent. I wouldn’t buy one of these machines if it was the last washing machine I think I’d go down to the creek or something. These things are pieces of shit.
![Eminem - Fuel (feat. JID) [Official Lyric Video]](http://i.ytimg.com/vi/t5H_CewqpKA/mqdefault.jpg)
Our lg does this on every cycle no matter what we wash! It’s been doing it for 6 months now. The washer is 7 years old! Thank you
Check the shock absorbers they might be worn otherwise the speed sensor might be gone too
@@askmrwashywashycuál es el sensor de velocidad?
@@askmrwashywashy Where is the sensor located?
I had this problem while washing one small rug. Normally I wash all 5 bathroom rugs at once with no problem. thank you for your help and good advice on what fabrics to wash together.
Welcome glad it helps
The old-fashioned washers didn't have this issue. You just throw it in and boom its done. All these new washers are to sensitive and just meant for repairs. Thanks for the great info.
yes sadly true new ones are very sensitive. Lg washers tend to be better though
This washing machine is a nightmare
No
Agreed
We've been very pleased so something must not be set right with yours. Maybe read the manual?
I have done all the above and still get the error. I have even reset via unplug and no issue it was a perfect working for 5 years no matter the side of load now I’m having nightmare issues
@@charysma195all this is happening to me right now like shit
Great info, thanks. The wife only had about three hand towels in there so most likely was just that there was barely any weight and led to poor distribution. Thanks again!
Welcome. So glad you were able to sort it out
Thanks for saving me a big repair bill!!
Agreed, spent a fortune on a 14kg front loader to be able to wash a duvet. Can't do it without a UE error.
Awesome video man thanks. My question is, after I replace the two bearings for the drum my machine doesnt want to go into the fast spin cycle it gors clockwise and counterclockwise trying to balance load without success.i tried it with an empty drum and same problem. Could i have installed the drum wrong????? I was ultra careful putting it back together. Thanks buddy
Thanks my dude.
I was washing a small rug, and thought I'd new to buy a new combo washer/dryer
Same
Thanks brother for sharing excellent informative video JazakAllah Khair God bless you Thanks again
Welcome glad it’s helping you
Thank you so much I didn’t know what to do last night 🙏🏻❤️❤️❤️❤️ and it was because I put two different blankets
My Aeg Okokombi 9000 series washer dryer gives me error E75. What could it be? Thank you
hi sorry I have not come across that error before
I fill my washing machine, leaving about 4-5" between the top of the drum and the top of the dry clothes.
Saves a lot of water, power, and soap.
Never had the machine failed for 12 years.
I'm also sure, the savings will pay for my next washing machine.
Hello..one question.
How can know unbalance error?
What is sensor metod??
Thanks for.you support
I had bearings go out on mine and grinding, then it started throwing a UE code instead of spinning so I replaced the spider and the lower/rear tub that had the bearings. I also replaced all 3 shocks. Now it stopped making the grinding sound but I'm still getting the UE error.
When I took the rotor and stator out, I noticed a chunk of the magnet on the rotor had been broken out, about 1" square (2.5cm) Could that be causing the UE error or should I be looking elsewhere?
It runs through the wash cycle with no problems at all, but it always gets the error code instead of the high-speed spin at the end of the cycle. (or any spin at the end of the cycle)
Please help me.
Does machine also shakes violently before showing UE error?
Just now after UE error my washing machine 1100and 1200 spins are not working, can I correct it myself. Or can I give only spin tomorrow morning without washing? kindly suggest
Do I have to loose d nuts and bolts at the back of the machine before making use of it???
yes yes they are transit bolts otherwise it will walk around
Thanks for info, i got this UE error because i just wash one towel in washing bag but if i take it out, the washing machine working fine
Hi thanks I like your video. I need your help to trace my lg machine. My machine when I start any cycle drain moor start .. not stoping till i stop ofter one minute motor stop.please tell me whate to be problem. Thanks in advance
I recently chaned the drain pump because of the de error and it now drains properly. Since then the cycles work properly and have checked all of the balance situations as you commented on but at the end of every spin cycle I still get the UE error. I then have to run another spin cycle or 2 to finsh the load. It also seems to not get all of the soap out. Any clues. The diagnostics check out well when you press the soil spin buttons.
Hi. in my experience it is an issue with the motor if ue error persists. How long have you had your washer ? There is 10 years warranty on that direct drive motor so you could give Lg a ring and see if they can send you a new motor. If they won';t give you one for free try and change the speed sensor on the motor I did a video on how to change that as well ruclips.net/video/cMw5ro-eWZ4/видео.html
Hi, im having the same problem. How did your solve? Thank you
What if after doing all as directed in the video the UE code persists? The load of a heavy towel, thus very heavy when wet, will wash fine but UE code appears when tries to go into spin cycle. First load to activate the code included a medium sized blanket with the towel. Have washed these items separately & together in the past. If have gotten UE code in past went through these steps and it cleared,
Man I love u thanks for the tutorial
Hey Mr washy my lg front loader is not going on washing cycle help please
Thanks this video is really helpful 🙏🏻
Welcome glad it helped
WM1812CW Endless UE after replacing main bearings, water seal and spider arm. Replaced Hall sensor. Made sure all drain lines are fully open. Changed all 3 shocks. Ran machine empty (no items in washer) through rinse and spin several times. In order to eliminate a variable, I Drained residual water from bottom at pump, then continued the cycle at "MIN 10". Motor always spins slowly left and right through the balance check phase; then throws UE at "MIN 10". Can see Rotor wobble in and out about 1/8 inch when restarting after a "MIN 10" cycle stop. Have restarted cycle after MIN 10 shutdown numerous times, each time the basket is empty and the whole system is devoid of water.
I do not know what sensor is dedicated to detecting a balance problem, or if not a sensor, how the motor could throw a UE. If there was a test manual, it would help.
Motor stator and rotor have residual rust deposits from the leaking main bearing seal. It does not make sense to me how this residual material could affect motor, stator, rotor or sensor operation, as it was dirtier before the bearing repair and washed many cycles of clothing for months before it became obviously noisy, telling us the bearing and seal had failed.
All comments appreciated,
Thank you!
Thank you very helpful
You're welcome!
Hi dear, just having same problem with my washing machine. I just pause it but problem was I couldn't open the door just like on your video.. I hope you have an answer for me thanks...
Washer should unlock if you give it a minute or 2.
Thank you good Sir.
This has happened 4 times in a row....each time I've added more and more stuff. About 4 blankets total.
Blankets are a bit tricky try to load maybe two at a time and use the bedding setting
Mines doing this after the end of the cycle and the door stays locked so I can’t open. What can I do to release the door?? TIA
There must be water in the washer. Empty the filter on the bottom right hand corner
So helpful! So kind thank you 🙏😊
You're so welcome!
Is it serious can my washing machine wont work anymore
What should I do if I see UE code
Thanks Great help
How do you reset and clear the UE error code ?
it could be also bearing problem,too😊
Thank you
Welcome
I have another error DE in washing machine LG 6kg please help me
ruclips.net/video/VNZRYWLGOjw/видео.html
Thanks
welcome glad it helped
Thank you for the information.
welcome glad you could find value in it
Mine leaves my clothes SOAKING WET and extremely hot...
Hi please check that you haven’t mixed the hot and cold taps
Thank you, sir!
Welcome glad it helps
Mine is just a bath mat and on 18 min but at 9 min it stops with ue
Yes it will do that coz it can’t balance the bath mat
Thanks you 🙏
welcome glad it helped
Thank you. I’m lame!
This only happens when my HUSBAND does his work clothes! 🤦🏼
Thnx so much sir....
OK I have one of these in the townhouse that I rent. I wouldn’t buy one of these machines if it was the last washing machine I think I’d go down to the creek or something. These things are pieces of shit.
Will Tey and see if it helps
U5 ERROR ANYONE??
PLS THNX
Why does my LG say ue after it's finished washing
I think it has a problem balancing the weight while spinning
Thank you so much
Thank you
Thank you!!!!
Thank you!!!