Dug a super deep wheatie at DigStock with the Sweeper program and on test with a silver dime one inch below and between 2 square nails… swinging “down the barrel” separated AND correct ID
Awesome! That sweeper program works good. This one would as well. Its the high Disc impacting the unmasking. I like the way it sounds with the offset in my test garden, and using FT will help identify nails with the silencer at 0. Silencer at 0 in Sens FT is (if i remember correctly) -2 compared to the fast program which is helping the Ids but caused users frustration with nails when that version was released.
A good, well thought out, in-ground test patch is "consecrated ground"🙏. Every metal detectorist should strive for such holey-ness and denounce all "small coffins with poke- holes" in as being, the death real of testing and a sacrilege , I think😉 . Yours and Todd Brown's are indicative of "hallowed ground". I hear tell Todd is starting testing again in Spring, after a few years break. Two honest testers with two good in-ground testing platforms will be a 'double-score'! Cheers for this video Mike; as always a fair and interesting pleasure to tune in to your channel👍
I had doubts that the Tekkna was a magic program. Fast got them all, If the disc for Tekkna was normal it would have ID the level 3 I believe. SRA's sweeper would have got them all. Run a test with his.
Yes, normal Disc of 6.8 and Sensitive FT is the program (base) to use for unmasking. Keep the silencer below 2 if you can. 0 in Sensitive FT is lower than 0 in other programs.
Hi, i use sensitive ft as a base but i change it to two tone. Audio high square, Disc of 7, An iron tone at 202 and everything else 900. Silencer 0 BC 2 (helps ignore large iron) add silencer if needed because of the nails. Once you go past silencer 2 your unmasking has been impacted quite a bit and will get those 7-9 IDs.
Just purchased the WSA 11 XL headphones. I have them paired to my Deus 2 and can hear the remote but not the coil. Must I pair these headphones to the coil? My WS6 headphones work as they should. Thanks
Hi, I am mainly a coin hunter at old home sites. Most of the places I hunt are iron laden but some have modern trash mixed in. Currently I am running a program based on the general program. But I find I have falsing on more modern rusty nails and small bits of fence wire coming in at an 85 and sounding good as well. Here are my settings what do you recommend I change? Ver 1.1, base program general, max freq 40, 5 tones, disc 6.8, bin 2 53, bin 3 65, bin 4 72, bin 5 73 and up. Running hi square audio, fe tid off, iron vol 7, silencer 2, reactivity 2.5 (adjusted based on the site, audio filter 0, audio response 5, 0 notch, 0 bottlecap. Thanks for any information. Btw, I am in Mo near the Arkansas border, are you also in Mo?
The nails drive me crazy at vdi 85/86 too. You can try silencer 3 and bottlecap 2 to see if that helps, you are going to be masking targets though. I use the D2 in 2 tone high square as a relic machine. If you try full tones in sensitive FT you might fine you are getting more info in the audio to help with those nails. I don’t have a (settings) way around that issue, i deal with the same thing here in RI. The rusty hand forged nails are a pain in the a@@.
I posted this as an issue on Facebook forums and was called a liar, newbie etc. Glad to find I am not crazy. I will try bottle cap reject to see what I can find. I may look at building my program off of Sens FT or Fast. A friend in England dumped his d2 out if frustration and went to Nokta. He claims it separates better than his d2 did.
So one question I have not tried this program in the field. Are you running 2.0? The reason I ask is since I went to that version I am not seeing the 08 -09 VDI. I have been running it since it came out. Thank for sharing. I do like you do switch between programs and see what happens to the signal. I can say most of the time I am in SenFT and not fast.
@@IffySignals interesting, I have the manticore but keep going back to the deus. I did like the look of the versa results, I asked as I was thinking of selling the manticore and getting a versa, the battery life annoys me with the manticore. Thank you for the input. Looking forward to seeing how the magnet program gets on with depth, I can’t say I have noticed any difference.
I saw in one of your videos when the update came out that the tid problem had been fixed or am I wrong? You showed that the problem was gone with the new update... What are the settings to resolve this issue? Why doesn't it work in the video anymore? Discrimination too high?
Yes, there were nail falsing issues with that update that many people mentioned. They have put out a new update to correct it 1.10, sensitive FT is a great base to keep the Ids just do not go over silencer 1 or 2 or it will give you the low Ids again. Its a trade off.
@@IffySignals I believe that program number 3 is the least suitable for unmasking non-ferrous targets. Why does it keep the 1.0 version silencer more aggressive than the other versions even at 0...on your 3D tests if you chose the Prog number two or the four with zero silencer and disc at 30-40 you would get the correct IDs?
@@brillero2356 disc 30-40 is tough, if you run silencer 1-2 will hinder it. Silencer 0 on sensitive FT is (i think negative 2) making it more frustrating on nails.
@@IffySignals I always use silencer on 0 in iron filled areas with prog two.. never had low id problems to me it seems to unmask perfectly... I'm on version 1.1
@@brillero2356 its good that you can keep it that low on your sites. I can use 0 with sensitive ft on clean sites but when i use it around the cellar holes its pretty rough. The hand forged nails sound very clean. Doable but annoying.
Definitely! Coming soon, just wanted to make sure the other testers around the world were also happy with it and nothing was going to change. Its good to go and the update is coming really soon.
Yes, ear is first. I am guilty of digging ID’s 40 and up. You can see my small gold giving a 33 ish Id, so i am missing those when I’m only digging 40 and up.
I do ask question. it how you learn .. That programme does get you deep .. but the iron and coke is shocking on the deus2 .. .. how does it sound with two targets one iron nail round head with a coin ... sorry i think gary sings from the deus hymn sheet .. the falsing is frustrating ... .. i have the ctx , nox 800 and the deus2 .. and i have ask garry question but i know fine well he will not knock anything deus 2 .. deus 2 is over hyped and they deus guys know fine well ..
The D2 is a great machine but it does have its quirks. The first is being the 85/86 on nails (my hand forged nails here on 1600-1800 sites. The 2nd it will unmask very well but you get a 7-9 ID so you have to dig them. For me allot of nails also fall into that range. The best machine i have seen for unmasking currently while maintaining a good ID and also being able to knock out large iron and nails is the Rutus Versa with the new update 3.7. It also has Dual mode which XP and ML do not currently offer.
@@IffySignals you are digging more iron .. and the machine falsing on Iron is. a shocker .. coke coming in as the same as small silver hammered coins .. what is that all about. .. every time i take it out i have even more questions about it .. i have also found it sucks at killing emp something i never have issues with with a mineland ctx or the 800 .. i like the machine. but it still need sorting inside. .. falsing is my biggest gripe ... iron i can live with .. the Iron value is not a volume is more of a discrimination .. i could be wrong with all this. .. time will tell .. but many thanks for your videos .. steve from scotland
Fast destroys tekkna. Score destroys tekkna. Who's next? I think I would pass on that one. In order to hit one little thing better you're going to be missing a whole lot of other things instead. Pick your poison.
Currently the magic happens between 7-9 ids on the D2. Sensitive FT will be your best base program for unmasking with the most recent update but cannot disc those 7-9’s and keep it below silencer 2.
Well, it seems to work well for allot of people but its not for me. That high of a discrimination on a machine that plummets down the Id when a target is near iron cannot be used on my sites, not with a discrim in the 40 range. I do like the FT offset feature on the D2. The program works really well for coin hunters. I think that is the target audience of the Tekkna.
@@IffySignals well i hunt mainly coins but there are many types of ancient coins here with different sizes and made of different metals(bronze,copper,silver,gold etc).When they are small and deep they tend to ring at lower id numbers and that 40+ disc is messing with the way they sound.When you combine this with the iron in the soil the problem gets bigger.
Thanks for great display and for imformation thanks for vid and your time.
Welcome Fred 👍
Dug a super deep wheatie at DigStock with the Sweeper program and on test with a silver dime one inch below and between 2 square nails… swinging “down the barrel” separated AND correct ID
Awesome! That sweeper program works good. This one would as well. Its the high Disc impacting the unmasking. I like the way it sounds with the offset in my test garden, and using FT will help identify nails with the silencer at 0. Silencer at 0 in Sens FT is (if i remember correctly) -2 compared to the fast program which is helping the Ids but caused users frustration with nails when that version was released.
A good, well thought out, in-ground test patch is "consecrated ground"🙏. Every metal detectorist should strive for such holey-ness and denounce all "small coffins with poke- holes" in as being, the death real of testing and a sacrilege , I think😉 . Yours and Todd Brown's are indicative of "hallowed ground". I hear tell Todd is starting testing again in Spring, after a few years break. Two honest testers with two good in-ground testing platforms will be a 'double-score'! Cheers for this video Mike; as always a fair and interesting pleasure to tune in to your channel👍
Hahaha! Thanks Tim!
Good job Mike thank you.
Welcome Jimmy
Great video Mike thank you!!!
Thx Bill
Hi Iffy, going to try same settings of tekkna in fast program.
Good luck 👍
Hope your doing great Iffy👍🏻💯
Jeremi! Doing good bud. How are you?
@IffySignals doing great my friend 💯
Bonjour ; merci pour la démonstration 👍. Sur ce programme la discrimination est à combien?
It uses high discrim but FT with an offset.
Odd question here, but have you tried this in combination with the XY screen?...
Hey, the XY is very messy in my garden because its not clean.
Good video!
Thanks
I had doubts that the Tekkna was a magic program. Fast got them all, If the disc for Tekkna was normal it would have ID the level 3 I believe. SRA's sweeper would have got them all. Run a test with his.
Yes, normal Disc of 6.8 and Sensitive FT is the program (base) to use for unmasking. Keep the silencer below 2 if you can. 0 in Sensitive FT is lower than 0 in other programs.
Hello, what program and settings do you use to run on trashy and iron sites? With deus 2 small coil? Best unmasker on that mashine. ❤
Hi, i use sensitive ft as a base but i change it to two tone. Audio high square, Disc of 7, An iron tone at 202 and everything else 900. Silencer 0 BC 2 (helps ignore large iron) add silencer if needed because of the nails. Once you go past silencer 2 your unmasking has been impacted quite a bit and will get those 7-9 IDs.
Just purchased the WSA 11 XL headphones. I have them paired to my Deus 2 and can hear the remote but not the coil. Must I pair these headphones to the coil? My WS6 headphones work as they should. Thanks
You may need to update them, plug them in and check the software. When you go to the XP site it will walk you through the steps.
Thanks for the reply.
Hi, I am mainly a coin hunter at old home sites. Most of the places I hunt are iron laden but some have modern trash mixed in.
Currently I am running a program based on the general program. But I find I have falsing on more modern rusty nails and small bits of fence wire coming in at an 85 and sounding good as well.
Here are my settings what do you recommend I change?
Ver 1.1, base program general, max freq 40, 5 tones, disc 6.8, bin 2 53, bin 3 65, bin 4 72, bin 5 73 and up. Running hi square audio, fe tid off, iron vol 7, silencer 2, reactivity 2.5 (adjusted based on the site, audio filter 0, audio response 5, 0 notch, 0 bottlecap.
Thanks for any information. Btw, I am in Mo near the Arkansas border, are you also in Mo?
The nails drive me crazy at vdi 85/86 too. You can try silencer 3 and bottlecap 2 to see if that helps, you are going to be masking targets though. I use the D2 in 2 tone high square as a relic machine. If you try full tones in sensitive FT you might fine you are getting more info in the audio to help with those nails. I don’t have a (settings) way around that issue, i deal with the same thing here in RI. The rusty hand forged nails are a pain in the a@@.
I posted this as an issue on Facebook forums and was called a liar, newbie etc. Glad to find I am not crazy. I will try bottle cap reject to see what I can find. I may look at building my program off of Sens FT or Fast. A friend in England dumped his d2 out if frustration and went to Nokta. He claims it separates better than his d2 did.
Hi, can you give me the perfect setting for fast programm?
Hi, Send me an email with your hunting style/conditions.
Iffy if you lower disc. Down to 6.8 with tekkna program does it hit level 4?
Yes
So one question I have not tried this program in the field. Are you running 2.0? The reason I ask is since I went to that version I am not seeing the 08 -09 VDI. I have been running it since it came out. Thank for sharing. I do like you do switch between programs and see what happens to the signal. I can say most of the time I am in SenFT and not fast.
This is 1.10, i am pretty sure its the same as 2.0. 2.0 is needed for the new Xtreme Hunter.
@@IffySignalsOK, I am curious if you test it, for me it seems different, so I think something was changed with the programs.
@@DetectDigSmile ill try it out and let you know.
Have you tried the magnet program? I run it, would be interested to see how it does.
Hey, no never tried it. Ill load it up and see how it is.
@@IffySignals It would need done on 0.71, that’s what it was setup for. Thank you. 👌
@@IffySignals I forgot to ask, out off all the machines you have tested on both test, which would you say was the best all rounder?
@@shaungrant5259 right now i would have to say the Manticore. The Versa is really good as well but not available in the States
@@IffySignals interesting, I have the manticore but keep going back to the deus. I did like the look of the versa results, I asked as I was thinking of selling the manticore and getting a versa, the battery life annoys me with the manticore. Thank you for the input. Looking forward to seeing how the magnet program gets on with depth, I can’t say I have noticed any difference.
Awesome video. So much good info. On the tekkna program. Where did you get your cover for the rc? It looks like a really good fit for it.
Thank you! ebay bells. www.ebay.com/itm/116088695526
Thank you!
Good video
Thank you!
I saw in one of your videos when the update came out that the tid problem had been fixed or am I wrong? You showed that the problem was gone with the new update... What are the settings to resolve this issue? Why doesn't it work in the video anymore? Discrimination too high?
Yes, there were nail falsing issues with that update that many people mentioned. They have put out a new update to correct it 1.10, sensitive FT is a great base to keep the Ids just do not go over silencer 1 or 2 or it will give you the low Ids again. Its a trade off.
@@IffySignals I believe that program number 3 is the least suitable for unmasking non-ferrous targets. Why does it keep the 1.0 version silencer more aggressive than the other versions even at 0...on your 3D tests if you chose the Prog number two or the four with zero silencer and disc at 30-40 you would get the correct IDs?
@@brillero2356 disc 30-40 is tough, if you run silencer 1-2 will hinder it. Silencer 0 on sensitive FT is (i think negative 2) making it more frustrating on nails.
@@IffySignals I always use silencer on 0 in iron filled areas with prog two.. never had low id problems to me it seems to unmask perfectly... I'm on version 1.1
@@brillero2356 its good that you can keep it that low on your sites. I can use 0 with sensitive ft on clean sites but when i use it around the cellar holes its pretty rough. The hand forged nails sound very clean. Doable but annoying.
That Gladiator Tho
You like them? Allot of fun. 👍
@@IffySignals took the doors off was the first thing I did
I swapped my hard top for the 1/2 soft. I have kept it on all winter. No issues. I have not had the doors off yet.
Hey Iffy we gonna see anymor versa vids?
Definitely! Coming soon, just wanted to make sure the other testers around the world were also happy with it and nothing was going to change. Its good to go and the update is coming really soon.
@@IffySignals cool I ordered one so can't wait to try it
@@IffySignals is the depth comparable Mike to other machines we have ,deus 2 etc
Equinox 900 try for these same goals
Sorry, i do not have a Nox anymore.
If you go by ear fast is far better
Yes, ear is first. I am guilty of digging ID’s 40 and up. You can see my small gold giving a 33 ish Id, so i am missing those when I’m only digging 40 and up.
Yes, but let’s get realistic. Do you have enough time in the day to dig all?
@@makeitwork2650 not me, someday. Work and fam leaves this to a weekend hobby.
Doubt I'm going to use teckna thwn 😆
Not my style either but I’m sure fun for cherry picking.
I do ask question. it how you learn .. That programme does get you deep .. but the iron and coke is shocking on the deus2 .. .. how does it sound with two targets one iron nail round head with a coin ... sorry i think gary sings from the deus hymn sheet .. the falsing is frustrating ... .. i have the ctx , nox 800 and the deus2 .. and i have ask garry question but i know fine well he will not knock anything deus 2 .. deus 2 is over hyped and they deus guys know fine well ..
The D2 is a great machine but it does have its quirks. The first is being the 85/86 on nails (my hand forged nails here on 1600-1800 sites. The 2nd it will unmask very well but you get a 7-9 ID so you have to dig them. For me allot of nails also fall into that range. The best machine i have seen for unmasking currently while maintaining a good ID and also being able to knock out large iron and nails is the Rutus Versa with the new update 3.7. It also has Dual mode which XP and ML do not currently offer.
@@IffySignals you are digging more iron .. and the machine falsing on Iron is. a shocker .. coke coming in as the same as small silver hammered coins .. what is that all about. .. every time i take it out i have even more questions about it .. i have also found it sucks at killing emp something i never have issues with with a mineland ctx or the 800 .. i like the machine. but it still need sorting inside. .. falsing is my biggest gripe ... iron i can live with .. the Iron value is not a volume is more of a discrimination .. i could be wrong with all this. .. time will tell .. but many thanks for your videos .. steve from scotland
Fast destroys tekkna. Score destroys tekkna. Who's next? I think I would pass on that one. In order to hit one little thing better you're going to be missing a whole lot of other things instead. Pick your poison.
Thx Steve 👍
Probably the rutus versa with the upcoming newest version😊
Try my FT Pro program. I’ve had 2 gold and many silver
So it's not witchcraft after all....
Currently the magic happens between 7-9 ids on the D2. Sensitive FT will be your best base program for unmasking with the most recent update but cannot disc those 7-9’s and keep it below silencer 2.
Iffy, any more information on the Rutus ?
Yes! Update is great. Really impressive. Should be released soon. I will show it more after the release.
I swear tekkna is the shittiest prog Gary ever made...
Well, it seems to work well for allot of people but its not for me. That high of a discrimination on a machine that plummets down the Id when a target is near iron cannot be used on my sites, not with a discrim in the 40 range. I do like the FT offset feature on the D2. The program works really well for coin hunters. I think that is the target audience of the Tekkna.
@@IffySignals well i hunt mainly coins but there are many types of ancient coins here with different sizes and made of different metals(bronze,copper,silver,gold etc).When they are small and deep they tend to ring at lower id numbers and that 40+ disc is messing with the way they sound.When you combine this with the iron in the soil the problem gets bigger.
@shamanism9416 ahh understandable. 👍