Finally! Quick Guide To Setting Up Crossfire Nano! How To Wire & Install & Program
HTML-код
- Опубликовано: 27 авг 2024
- In today's video we will quickly run through wiring, installation, and programming of your TBS Crossfire Nano RX. There are tons of videos that drag on and on about this receiver, but if you want to just learn how to put it in and fly your quad then you have found the right video!
How to set up RSSI / LQ for your crossfire:
• How To Set Up RSSI / L...
Where to get a TBS Crossfire Nano RX:
www.myfpvstore...
Where to download TBS Agent:
www.team-black...
How to fix spinning out of control quad in betaflight:
• Drone just flips and s...
How to set up modes in betaflight:
• How to set up Arm/Disa...
If you need new firmware on your flightcontroller:
• How To Flash New Firmw...
Where to get other TBS Crossfire Products:
www.myfpvstore...
===▶️ / drainmanfpv
▶️Crossfire Nano SE:
✔️www.myfpvstore...
▶️Unify Pro 32 HV:
✔️www.myfpvstore...
▶️Caddx Air Unit for DJI
✔️www.myfpvstore...
▶️Custom DrainMan Motors!
✔️www.myfpvstore...
▶️Smoke Stoppers:
✔️amzn.to/3tsWhhq
✔️amzn.to/2YL7trB
✔️amzn.to/3tsMt77
✔️www.myfpvstore...
▶️All Drone Pilots Need A Power Supply! Build Your Own!
✔️ • The Ultimate DIY Varia...
╔═╦╗╔╦╗╔═╦═╦╦╦╦╗╔═╗
║╚╣║║║╚╣╚╣╔╣╔╣║╚╣═╣
╠╗║╚╝║║╠╗║╚╣║║║║║═╣
╚═╩══╩═╩═╩═╩╝╚╩═╩═╝
/ drainmanfpv
/ drainmanfpv
▶️If you want to learn about LED's:
✔️ • Betaflight LED's !! Ev...
====▶️My Scope:
✔️amzn.to/2Y7NUtc
====▶️Cheap Version:
✔️amzn.to/2PC8Ogj
▶️DJI Air Unit: ($4 Cheaper Than Anywhere Else & 2 Day Shipping)
amzn.to/2PjqUDi
✔️or
✔️www.myfpvstore...
▶️How To Taranis:
✔️ • How To Frsky Taranis
▶️My Electronic Screwdriver:
✔️ • ES121 Electric Screw D...
▶️My Soldering Iron:
✔️amzn.to/2Oj95XS
▶️My Soldering Iron Tips:
✔️amzn.to/39IT453
and
✔️amzn.to/2Oj7r8C
▶️1.5mm Driver:
✔️amzn.to/3txYarX
▶️Radio Receivers:
✔️www.myfpvstore...
▶️Hobbywing:
✔️www.myfpvstore...
or
✔️amzn.to/31e6jFM
▶️Loctite:
✔️amzn.to/39QY5HE
▶️Screw Pack:
✔️amzn.to/2BPzBSq
====▶️How To Set Up A Throttle Cap: (Become A Better Pilot)
✔️ • The Ultimate Throttle ...
====▶️My Go To Pack:
✔️4s : www.myfpvstore...
✔️6s : www.myfpvstore...
====▶️Flight Controllers:
✔️www.myfpvstore...
====▶️ Quadcopter Frames:
✔️www.myfpvstore...
====▶️ The Goggles I use:
✔️amzn.to/3sQ5ksu (Comes w/ 2 Modules)
✔️Analog - www.myfpvstore...
====▶️My Radio:
✔️amzn.to/3sU9Fem
✔️Non-DJI: amzn.to/39dqI3c
✔️HD - amzn.to/2AVAEQo
====▶️ Video Module That I use (When Using Analog):
✔️ www.myfpvstore...
====▶️Bench Power Supply:
✔️amzn.to/3cpIOhE
====▶️Field Bag:
✔️www.myfpvstore...
or
✔️amzn.to/2TleAns
or
Ethix:✔️www.myfpvstore...
====▶️My 3D Printer:
✔️shop.prusa3d.c...
====▶️My Camera Used:
✔️amzn.to/2wX0eCg
====▶️My Cam Mic:
✔️amzn.to/3b2ZoUZ
====▶️Contact Me: @DrainManFPV on FB or DrainManFPV@gmail.com
====▶️I'Gizzle: / drainmanfpv
====▶️ / drainmanfpv
#Crossfire #Nano #TBS
Man I wish you were my Physics teacher. No BS , no overly complicated crap... just straight to the point.
Thanks a lot Buddy 👍🏻
Your training style is spot on. To the point, no BS, crystal clear. Incredibly helpful!
Yes, absolutely superb, the perfect balance of concise on point information for this audience without any unnecessary fluff.
He would make a great course trainer.
Sub'd..
instablaster...
Totally agree!! No nonsense, clear and quick!. Thanks!
am after 5 years of flying still a big fan of JB's explanation style,, but I must say, very clear the way you put it all , 💯% respect !!👌🔥
Glad I found this video. Something about how you explain stuff is so much better. No side information, just what you need. But yet still EVERYTHIng you need and straight to it. Good work!
This dude is straight to the point 👍🏼 ...no filler.
Wow, excitement!!! All stuff in one video, even howto Bind, ... and setup TBS CROSSFIRE Nano in FrSKY X9D , inclusive beta flight setup. Just AMAZING 😍😍😍
I can't tell you how many videos I've watched of tbs nano installation and this is the only one I understand. Thank you
Man, this is FINALLY the video I've been looking for to install my Nano. Well explained, excellent examples to show us not just tell us. Just the facts, I don't need to know the historic background and intricacies of a part like every other video seemed to do.
LUV YOU DRAINMAN!!!!! ALWAYS SAVES THE DAY WITH THESE YEAR OLD VIDEOS
spot on DM, love your delivery, no messing, you just get on with it. cheers Mick UK
Ive been in this for a couple years now and I still learn new things everyday... Thank you, noticed that my issue was not having the Channel 1 set to CRSF TX. I was scratching my head for a couple hours.
I’m watching these very helpful tutorial many times before i received my crossfire nano rx and tbs tango 2 and specially i never seen anything tutorials like these complete step and explain u every detail’s no fast forward like the other thinking newbie like me can get it right away ! Thanks man looking forward for more videos we do loved and appreciated this
Can’t thankyou enough man. I just setup my crossfire v2 module for my taranis qx7, I flashed the latest version of open tx and copied the SD card contents then followed your tutorial all good to go! And side note, (for anyone who can’t find enough info on how to do it, yes the taranis qx7 access) can easily be setup with crossfire. It took me 5 minutes. And the access radios don’t need inverter mod. Thanks again!!
Thanks Drainman! Very helpful video for pilots new to CRSF.
Your video was amazing , using different flight boards your explanations your wiring everything was awesome thank you so much you made my life so much easier tonight.
I like your teaching style, u don't just blow past stuff, thanks bro
I concur.
Exactly the 'how to' video I was looking for.
Absolutely great video on explaining this process!
Nice work mate . Im a total noob n dont know my ass from my rx . 1st video that made sense to me . I hope your doin well and your you tube channel goes right off .
Looking forward to more . I like your style . Keep it simple and spot on facts thats educating people all over the world . Keeps ths hobby so much more accessible for people like me that have no idea and people looking to learn more , which eventually means getting out there and having fun sooner .
Thanks Drainman . Im bloody glad I stumbled on to your channel 😁
Man, I had to agree in comment with the others, dig your to the point, no BS style. Get it done, make it work, simple steps, go fly. 🔥🤘
Appreciate all your help. As you know this can be very frustrating at times. You walk me through it, thank you sir
💯 % best tutorial i have ever seen i just did it in first try as a begginer 👍🏻
Only video that has made me understand all this
I love your quick no bullshit style. I referenced this video a bunch of times while installing today
Have a crossfire module and the nano on the way. Your vids are very helpful, thanks. Happy flying.
You're gonna love it👍
appreciate the video for new guys -TBS support =)
I love the detail used for this video.
I anticipate getting my crossfire in hand tomorrow to try all this. My soldering iron is ready and waiting.
Every other source of information confuses me. Your videos usually have me unsolder, resolder, change betaflight/iNav settings, and BOOM! my stuff works
Such a good video explained everything I needed to know. Solid work
Nice work man. Short and to the point as always. Love your vids Keep up good work
Clear, simple and to the point. Thanks much!
Hey brother thanks.. your videos were a blessing. Most assume all computer guys. Your videos made it possible for me to enjoy hobby I love. Sincere thanks. God bless
Brilliant! So well explained even tripod could understand! 🙂 Get it?
you are the man. greetings from malaysia. u just got 1 sub from asia.
Step by step, thank you so much.
This is exactly the video I needed!
Always find clear and right to the point videos on your channel. Appreciate your time brother!
very well explained... just what i needed as a new CRSF user. thank you.!!
I prefer the regular antenna too. Another great video man, keep up the great content👍
Nicely done video. Cleared up my confusion with tx and rx. Thanks for the help!
Great tutorial, I ordered (4) receivers and the Tbs Crossfire Micro V2. Switching (4) quads from the frsky R9 system over:) thanks for this info I’ll be making use of it shortly.
Very clear tutorial.
drain man you are the best
thanks for such amazing and educational content!!!
Drainman, what is the board you are using to clamp down your CRSF nano receiver? Did you print that yourself or did you buy that? Love the videos, will be installing my crsf nano for the first time after watching this video! Thank you for the amazing content!
Very good explanation! Thanks a lot!
You just made my setting up my Crossfire a whole lot easier!! 😊 Thank you very, very much! Now, do I have to run the Crossfire Agent or is it optional? And what about setting up Smart Audio? Sorry to ask so much but you have a knack for explaining things that I can wrap my head around. 😉
Just subbed to your channel! Straight to the point... I really appreciated this video! Just cruised through the setup and all is good...you are tha man !or should I say DrainMan!
haha thanks man!
short and sweet - love the quick reference. thanks!
i still refer back to this video every time lol
No fckn about good info straight to the point... gets a sub from me..
great tutorial clear and straight
Thanks for this and a ton of your other videos. You’ve taught me a lot!
New subscriber here. Awesome! Straight to the point! Keep up the good work. I appreciate you!
Thanks for the video very helpful
PERFECT explanation!
Nice soldering!
Perfect info 👍🏻👍🏻
Super, man.Thanks!
Didn’t know people were still doing things real quick.
Great video. Thank you
THANKS DRAINMAN
I'd like to see a video on soldering up one direct connect servo to the nano extra pads.
Thanks for this!
Thanks mate you solved an issue I was having, cheers
Awesome 😎 thanks 😊
Thank You this helped me alot im new to Crossfire
Did this and it worked, now for some weird reason it doesn't. haven't soldered anything, the rx and controller still connects between each other but in betaflight and real life, no props are reacting. ideass?
Awesome video!. Thanks. Im curious....Why are you called Drain man?.
I was also wondering how many channels do you get with the crossfire? I needed more than 8 channels...
Your video really helped me. Thank you!
Can you do a video on wiring battery direct to this receiver. I use it on an rc plane with just servos and would like to know my battery voltage with telemetry
100% excellent tutorial!
Great detail thanks! OK I followed your instructions and all went well with everything working except smart audio. It's still on the same UART as before and the Nano receiver is on a different UART. When I enter the VTX settings in my goggles everything looks as it should but no changes are saved. What am I missing?
Thank you for the video! I have a Goku GM415T FC and I can’t figure out where to solder the RX to. Any tips for cases where there are no descriptions on the FC itself? Thank you!
Where do I find that vice for holding boards????
I got mine from Amazon
www.amazon.com/gp/product/B077SBC232/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Thanks!
Where you have the white wire on the nano is the Rx pad
someone told me that the receiver should be tx1 and rx1 because they are more responsive. is that true? please answer
Hello great job, I came across your channel and I have a question... What if it's a TBS 6ch diversity rx how would you wire it for SBUS.
Hey drainman you said that both the channel 1 and channel 2 connect to RX😄
I have a taranis x lite 9 can i do this same installation?and if i buy a betafpv with crossfire controller can i just bind and fly?
Thanks alot👍
another great one!!! keep em comin
question, I purchased the nano rx. Do I need the module for the taranis?
Yep
So to clarify we need to purchase the crossfire system in order to utilize these on our kwads?
Great channel..👌i'v wired in my Crossfire nano to my old kiss FC QUAD and bound it to my Qx7,solid green..But i cant get any reciever/stick movement in the Kiss Gui..!and wont Arm off my switch like it did before... I was using an RX8 reciever before..Any advise would be most apprieciated Drainman,🙏
Sorted..all i needed was kiss lua scripts...😉
Nice. What about OSD in BF. Do you need to select anything else in the ports tab to actuate OSD or will it just work now?
Thanks for video, I'm new to crossfire but I have the micro tx v2 and nano receiver, I'm trying to get connected to mission planner, I'm using f405 wing flashed with inav 2.5.0 would I wire my receiver the same as you to make this happen? Thanks again
I have a question, does it make a difference if it says R3 T3 on the flight controller and not RX3 TX3? I have a t motor f4 flight controller and it only says R3 T3, I’m very new to this and don’t know if that matters.
Unfortunately I'm have trouble with mine I have the jumper t8sg plus the crossfire is bound but no stick movement.....iflight 45a stack
Thank you very much for this useful sharing. Would you like to help me: i use tango 2 and craf nano rx. yesterday my rx antenna was released when I flew it, after that my rx continued to blink and ask for bind. I already bind and after unplugging the battery, the RX continues to blink again. Is my RX broken? Thank you 🙏🙏🙏
Thank you for the good content! where can we get the pcb holder?
Bro you should have more followers than JB!
how can i know which color is which , can you share the manual of tbs nano to see which color of the wire is on the appropriate pad
So I set up everything and it works awesome but.....I'm on 868hz and I'm in the US and when I select 915hz it makes me receiver turn red??? Any idea?? Do I have to re bind it????
Hi, what did you use to give your flight controller power??
What if your Rx was frsky and only has three wires?
Need some help Drain Man. I'm about givin on this Crossfire. Everything works but the moment I'm out about fifty feet out my Radio Master cries out low RF signal, a few more feet and I lose signal then goes into failsafe. Bought me three Nanos and its doing the same thing. Not the long range everyone else is getting. Did about everything down to even factory resetting. Only thing left haven't tried is changing the modules crossfire anttena to see if faulty but don't have one. Do you think it could be that? Keep up the good work.
1st things first, make sure your tx module is set to 250mW (or higher) and dynamic power is enabled. Also for the tx module, If in US, you need also to be on 915MHz - don't run the CE frequency or you may have these issues. Last is to make sure your antenna orientations are matched. If the antenna is horizontal on the quad, it needs to match on you TX (parallel to the ground). Also note if you mount an immortal t horizontally and the tips touch carbon fiber - you're effed; you gotta keep the tips off the carbon. If vertical on the quad, you also need the TX antenna to be vertical with the ground. Do these and it should be fine - I run a Micro TX v1 @ 250mW and I can get right at 4mi range on a 7" quad (single vertical immortal T). Good luck!
Can I get the exact same from Banggood?
unfortunately banggood does not carry this receiver :-(
if I have different colors for the wires. Let's say for instance I have green and orange.
Can I name them like
Green : TX
Orange: RX
So, therefore, TX on the nano pad ill solder it to the RX on the FC pad.
The same goes for the RX.
Because on the nano manual they name the pads as ch1 ,2,3,4