This us by far the easiest and most thorough examples to follow. I am new to cnc and have just finished building an MPCNC. I have just connected my cnc shield and Arduino UNO and was lost. I will go over thks video again tonight and try using your descriptions fur the first time. Again many thanks.
Ciaran Whelan Thanks to you for the feedback :-) The reason I made this video was beacause I had had the same problems figuring things out myself. Eventually after rooaming the internet for a while I figured it out. The same goes for the Arduino and the TB6560 connection. Thanks again :)
Wow that's awesome 😢😢 now i understand thanks bro welcome but i found one issue that's openbuild "please wait machine idle joging" what is this problem and machine is not running please if u help for this feedback.. Please 👍👍👍
Dear Willy . I'm using CNC laser mini 3018 Pro and after set some program . I see that Laser GRBL had lost $ 30,31,32 in GRBL Configuration part .So pls help how to get back it. Thanks
Greetings to you dear, thank you for this topic. When connecting for the first time, the motors never started, and the driver’s temperature rose. The motor took one pulse and stopped working or turning until the order given to it by the program was finished. Why didn’t the Nema 17 motor work smoothly and continuously???
Hello sir need your help kindly me to make my cnc machine of 5 axis but I am stucked in programming or firmware for 5axis tell me that how can I compile all c++ and header files into one single.ino file through that I can make some changes according to my machine and I can upload it then .
Thanks so much Willy. I now have to go back through all your videos and get a complete understanding before I embark on this journey. Are you able to do a video on samples or items you have been able to created with this machine
Jean-Noel Seneque No problem Jean :) I'm going to make stuff on the machine and make videos of it. So just stay tuned. Thank you so much for watching :)
thank you for the explanation. i would like to know how you did the homing and the point zero with grbl and arduino. and hw you calculate the step per revolution of your motor. i have the nema 23 Wantai stepper motor model 57BYGH115-003B 428 oz. Step Angle: 1.8 degree Voltage: 6.3VDC Current: 3 A/phase Resistance: 2.1Ohm/phase Inductance: 9mH/phase Holding torque: 30Kg-cm 428oz-in Rotor inertia: 810 g-cm2 Detent torque: 0.89 kg-cm Number of wire leads: 4 how can we calculate the step per revolution
Hi. If you watch this video, I explain how you calculate your step per rev. It depends on your setup, lead screw, belts etc. You can watch this video on how I zero the machine: ruclips.net/video/A1zlL3q23HI/видео.html
hello can you help me ,i have axis problem ,the maximum limit of my Y axis is 58mm ,i enabled soft limit , i start to move Y axis from 0 , but it move only -58 , alarm comes when I tried to move on positive direction ,how to solve this ,i also invert axis direction but i won't work if soft limit is enabled,it work only when soft limit is disabled
Hello Dear , possible help to solve a problem on my diy CNC ? problem is , the Z axis going down to make collision when machine start to move after I fix well the milling tool on top of the material block , I think it should be going up on first step then going down to start milling , hope can help on this , thank you very much .Regards John
@@WillysGarageNorway Hei, ja, det er grbl som er planen, har installert noe. Men er helt på ukjent grunn selv, så det blr spennende å se om jeg får det til å fungere, ellers har jeg en windows-maskin stående med mulighet for Mach3. men det hadde hvert greit å få alle komponentene montert i samme kabinett.
Thanks for you reply. I want to build this type of cnc plotter using Arduino GRBL. ruclips.net/video/k1vzT-T8LJA/видео.html . But everywhere they show only mechanics to a good level so that beginners can understand. But they don't cover the details of software. I tried too much to start building my cnc plotter but get depressed when question like these starts arising in my mind like - How do I set the zero position ? Direction of movement ? How do I calibrate ? What dimensions to choose and how to modify software part accordingly. Today morning I came to your GRBL config video and got some hope but still I am in a discomfort zone to start building my own cnc plotter. Why don't come with a simple video for beginner like me ? So many thanks.
Hello, I have built a CNC plasma cutter (MPCNC with GRBL control) and also use it with the Universal Gcode Sende program, but I have the following problem: The file has a length of 100mm, for example, but in reality it cuts me out to 300mm approx. All values in UGS are converted to mm (G21). What could be the reason for this and how can I correct this error? Please send me your feedback as soon as possible! Best regards Tobias
Check how far it moves when you tell it to move 10mm in joging function in UGS, measure how far the axis travels in real life. If it moves to short or long, you have to check over your travel settings to make the axis travels the lenght you ask it to travel
I think this problem in LaserGrbl v3.014 softwear setting. You can check in above laserGrbl in menu /Grbl/Setting/Jog Control /Grbl/continuos Jog. on/off Button has side to continuos Jog. Maybe on position is jog work. And off position Jog not work. I will checking at home. This time I am in office.
Hello...what to change on my gbrl settings on LaserGbrl software to achieve 50x50 cm engraving area on laser machine.When I downloaded Laser Grbl to exchange Benbox I uploaded one hex file as firmware.This is for some other machine and I have movement 30x30 cm.I want 50x50 to have engraving area.Machine which I have is 65x50 3w laser
Hello You told here (Video Minute 4:18) from the limit switches and that you come back to these in a lter Video. Does this information about using limit switches with the arduino exist in one of your Videos? I doesnt find there it in you Videos!
i am stuck help me ........... i am making 5 axis cnc milling machine by using arduino mega 2560 +1.4 ramps board i uploaded frimware but the E0,E1 is not giving output as Axis A and B but when i am switching it in 4 axis in grbl foam cutter then it gives E0 as Axis U so .... my problem is that i my board E0 and E1 which is not as Axis A and B ...... how and what changes i have to make in frimware to get This E0 and E1 as Output Axis A and B....... >>>first off all i have to make changes in c++ files and header files then... >>>second how i have to compile it in one single .ino file from bunches of c++ and header files of frimware Atleast help me out from my second problem because i don,t know how to make firmware for my machine into single .ino files to upload it in my machines................... please if somebody knows kindly help me to make it solved............
Hi. Very nice video. One question - is there a way to add 4th axis to arduino + cnc shield with GRBL? If not, what is the easiest / cheapest way to move to something else that can use 4 axis? Thanks
Ken Mais Thanks a lot, your feedback is appreciated :-) There is nothimg more fun than building your own machine and get it working. I'm glad my series helps you and let me know if you need some advice.
@@abrarmuqheeth1278 the speed can be set via the g codes. The speeds you set in $110 and on us only the maximum speed. So the speed is set when you make the g codes or the toolpath
@@WillysGarageNorway James Munro dieselphiend hey buddy how can I achieve slowest and smooth one rotation per minute with maximum torque ? Using nema 23 with tb6600 driver ??
Please reply😢 Here is a problem to my CNC grbl with stepper motor that the response time, I send the command to stepper motor but it doesn't revolve it revolve when I reset or close the grbl and again open or linked up with arduino then the stepper motor runs with the previous code which I upload but it does not revolve at that time I am also change the response time to one What is the solution please tell
Hello, while processing the g-code file I created with UGS in CNC, the CNC axes go to the place they need to go very fast when the carving work of a point is finished and trying to go to a different point (idle acceleration), which causes tooth skipping and the coordinate is distorted. I wonder if I need to adjust the grbl settings or the g-code file to reduce the speed of the axes in these transitions (idle speed).
I have the same problem. With settings $100,101,102 at 100.000 my Mill moves 25MM when asked to move 100MM. My thought would be to change to $100= 400.00, but that does not work.I also get noise and little movement. My machine is a cheep Chinese 3018 PRO. Is there another setting that needs to be changed?
Is acceleration that slow really necessary? I have not yet set but I'm wondering if setting mine to 200 would be bad. It's a 4mm pitch per rotation lead screw, and if I stall the motor, even at full speed the weight of the gantry can't move that lead screw.
Brilliant Mr. Willy! I just connected my first stepper to my machine as a test and its agonizingly slow! How do i fix it? Why just watch Willy's CNC part 12 of course! Thanks again for making it so easy!
Thanks Mr Willy,that's very helpful as always,I have question about the values of $110-$112,how would you know the values to set ? is it based on trying or based on calculation?
Mohamed Amine BIDA Thanks again. You can increase gradualy 110-112 after you have found the step/mm (100-102). Increase it until the stepper «stalls» or you dont want it to go any faster. Then you can decrease it 10-20% to perserve your steppers. The same goes for the acceleration setting :-) Good luck and appreciate the feedback ;)
Hi i'm working on DIY cnc router project but i have a problem with lead screw or ball screw it's expensive man i spent about 650$ for stepper Nema 34 and other stuff The question is Do you think if i use a belt my machine will be fast or what ??
Eng.Mudar A I dont think the machine would be any faster with belts. Belts are prone to wear and tear, they will slack and start missing steps and stuff. With the nema32 And 23 I would recommend going for some ball screws even if they are expencive. You can also do lead screws like me. Belts would not cut it, sorry
I installed limit switches... And when it is pressed motor stopped working but after that I need to restart everything....and it's not accepting any further commands.. is there any option to move the axis away from the limit switch automatically after it is pressed...
That means 400 steps per mm. Does your stepper have 400 steps per revolution? anyway you have to make these settings smaler when doing that.: $110=2000.000 $111=2000.000 $112=2000.000
I have the same problem. With settings $100,101,102 at 100.000 my Mill moves 25MM when asked to move 100MM. My thought would be to change to $100= 400.00, but that does not work.I also get noise and little movement.
Hello sir I used universal sender but i browse small gcode than is work properly but i download some g code like image but after browse universal send show empty file and show just complet 00.00.00 sec plz give solution plz sir
Hello sir I am using nema23 with tb6600 drive with 24 volt 10 amp, but with 32 micro stepping my motor rpm is very low around 30 or i change it into 1micro stepping then its rpm is around 150 with vibration I am trying to increase rpm of my stepper motor with smooth running Please help me....
Tushar Gajbhiye Hi sir, it sounds like you have to change the $100 $101 and $102 setting on the Arduino. This setting changes when you change the microstepping on a stepper motor. If you have a 0,9 degree motor and use full microstepping (fullstep) your stepper must have 400 steps per revolution. Then if your leadscrew travels 2 mm per revolution this value should be sett to 200. That means that the stepper motor travels half a revolution for the cnc axis to travel 1 mm.
Hello sir, My motor have 1.8 degre & if i change $100,$101 and $102 setting more than 300 value then my motor stop rotating and make loud noise and after noise decree then motor little rotate and stop
Tushar Gajbhiye With a pitch of 4mm, that means the ball screw moves the axis 4mm/revolution. In the GRBL you want to input the step/mm. You have a 1.8 degree stepper wich needs 200 step/revolution. That means in fullstep mode: (200step/4mm)=50step/mm In half step mode: (200step/4mm*2)=100step/mm So, first of try to put $100-102 setting in fullstep mode to 50step/mm and test the machine
Thanks Mr Willy,that's very helpful as always,I have question about the values of $110-$112,how would you know the values to set ? is it based on trying or based on calculation?
Hi and thanks :) You can calculate this value somewhat, but i depends on what drivers, steppers and PSU you have and use. So it's recommended that you increase this value until your stepper motor stalls and then decrease the value about 10-20%. This is so your system doesn't run on 100 % all the time :-) Did this answer what your question was about?
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
This us by far the easiest and most thorough examples to follow. I am new to cnc and have just finished building an MPCNC. I have just connected my cnc shield and Arduino UNO and was lost. I will go over thks video again tonight and try using your descriptions fur the first time. Again many thanks.
Ciaran Whelan Thanks to you for the feedback :-) The reason I made this video was beacause I had had the same problems figuring things out myself. Eventually after rooaming the internet for a while I figured it out. The same goes for the Arduino and the TB6560 connection. Thanks again :)
This is the best video by far for a simple straight forward explanation of this. My go to video for reference
Sorry for late reply :) thanks 👍👍
Wow that's awesome 😢😢 now i understand thanks bro welcome but i found one issue that's openbuild "please wait machine idle joging" what is this problem and machine is not running please if u help for this feedback.. Please 👍👍👍
Dear Willy . I'm using CNC laser mini 3018 Pro and after set some program . I see that Laser GRBL had lost $ 30,31,32 in GRBL Configuration part .So pls help how to get back it. Thanks
Greetings to you dear, thank you for this topic. When connecting for the first time, the motors never started, and the driver’s temperature rose. The motor took one pulse and stopped working or turning until the order given to it by the program was finished. Why didn’t the Nema 17 motor work smoothly and continuously???
Hi and thanks, sounds like your motor stalled. Therfore it stops 👍😄
Awsom Work bro :) thx for explaining in a very simple way for newbies
Thanks for the nice response :)
Man, I just learned everything I was wondering about my new GRBL cnc firmware. Well, done, thanks.
Jeff Pugh I’m glad I could help 👍🏻 Let me know if you have any more questions and thanks for watching :-)
thank u i am new in the field this video is very good for me
And thanks for watching 😀👍
Thank you! Very clearly shows the importance of each activity. I think it will be useful for many beginners.
Toto Thanks for watching :-)
HI Mr.
Thanks for your video. My y axis moter turning both sides when i press Y+ button,
Back and forth
?
@@WillysGarageNorway thanks for the reply. I have short video of the issue. But i cant send it to you on this platform. 🤔🤔🤔
@@isuruprasad1132 you can send it on my facebook page, link in the description
Can we give a feed rate of 1mm/min using this setup of Stepper motors?
Im not sure why you ask, but yes, everything is possible. But it depends on how high resoulution you need on that 1mm of movement in one minutte
Hello sir need your help kindly me to make my cnc machine of 5 axis but I am stucked in programming or firmware for 5axis tell me that how can I compile all c++ and header files into one single.ino file through that I can make some changes according to my machine and I can upload it then .
Thanks so much Willy. I now have to go back through all your videos and get a complete understanding before I embark on this journey. Are you able to do a video on samples or items you have been able to created with this machine
Jean-Noel Seneque No problem Jean :) I'm going to make stuff on the machine and make videos of it. So just stay tuned. Thank you so much for watching :)
Hello, I'm mounting my cnc machine following your videos. How do you calculate the $100, $101 and $102 values? thanks!!
Hi, i think I have explained it in this video. You need to find how many steps yor steppers need for 1 mm 👍
WillysGarageNorway you are the best!! Thanks a lot
@@urko19 Did you figure it out?
@@WillysGarageNorway Yes, what happens is that I did not take into account the microstepping
@@urko19 hehe, yeah I did the same thing
thank you for the explanation. i would like to know how you did the homing and the point zero with grbl and arduino. and hw you calculate the step per revolution of your motor. i have the nema 23 Wantai stepper motor model 57BYGH115-003B 428 oz. Step Angle: 1.8 degree
Voltage: 6.3VDC
Current: 3 A/phase
Resistance: 2.1Ohm/phase
Inductance: 9mH/phase
Holding torque: 30Kg-cm 428oz-in
Rotor inertia: 810 g-cm2
Detent torque: 0.89 kg-cm
Number of wire leads: 4 how can we calculate the step per revolution
Hi. If you watch this video, I explain how you calculate your step per rev. It depends on your setup, lead screw, belts etc.
You can watch this video on how I zero the machine:
ruclips.net/video/A1zlL3q23HI/видео.html
Thx you. I missed this part. Thank you.and it was well explained.thank you and great efforts
user new No problem 👍😀
hi. Why not show coordenates when move the cnc in universal g code sender ?
I think you can see coordinates when moving, but not sure. Why are you interested in that?
@@WillysGarageNorway. sorry my english.
I discovery GRBL 1.1 not totalitty compatible with UGS1.09. I made a downgrade now.
Thanks.
Ahh, I understand 😀
hello can you help me ,i have axis problem ,the maximum limit of my Y axis is 58mm ,i enabled soft limit , i start to move Y axis from 0 , but it move only -58 , alarm comes when I tried to move on positive direction ,how to solve this ,i also invert axis direction but i won't work if soft limit is enabled,it work only when soft limit is disabled
Can I set backlash in this software
Arsad Khan Arsad Khan Hi and thanks for watching. You cant set the backlash in this software
Hello Dear , possible help to solve a problem on my diy CNC ?
problem is , the Z axis going down to make collision when machine start to move after I fix well the milling tool on top of the material block , I think it should be going up on first step then going down to start milling , hope can help on this , thank you very much .Regards John
Dear sir please tell me how to increase speed of CNC machine
.. my CNC is running is too slow
If you have the settings correct, the steps per mm setting? Then you can try to increase your maximum speed setting and acceleration setting
veldig bra informasjon, takk.
Jeg holder på med en ox cnc, og tenkte å bruke Raspberry Pi 4 med protoneer modul.
Takk :) det høres ut som et spennende prosjekt :) Jeg har ikke vært borti Raspberry Pi så mye, bruker du GRBL mot den maskinen?
@@WillysGarageNorway
Hei, ja, det er grbl som er planen, har installert noe. Men er helt på ukjent grunn selv, så det blr spennende å se om jeg får det til å fungere, ellers har jeg en windows-maskin stående med mulighet for Mach3. men det hadde hvert greit å få alle komponentene montert i samme kabinett.
@@Cwn86 Det er bra å få samlet alt ja :) Si ifra hvis du støtter på noe problemer, kanskje jeg kan hjelpe 👍
WillysGarageNorway
Takk, det skal jeg gjøre.😀
Any videos for diy Arduino cnc plotter ? Please
Hi, can you explain what sort of videos you want/need?
Thanks for you reply. I want to build this type of cnc plotter using Arduino GRBL. ruclips.net/video/k1vzT-T8LJA/видео.html . But everywhere they show only mechanics to a good level so that beginners can understand. But they don't cover the details of software. I tried too much to start building my cnc plotter but get depressed when question like these starts arising in my mind like -
How do I set the zero position ?
Direction of movement ? How do I calibrate ? What dimensions to choose and how to modify software part accordingly.
Today morning I came to your GRBL config video and got some hope but still I am in a discomfort zone to start building my own cnc plotter.
Why don't come with a simple video for beginner like me ?
So many thanks.
Thanks all the best from John in Texas
No problem, and thanks for watching 👍😁
thank you for this video. can you show us on a video the wiring of the micro switches N/O on the GRBL shield and how to male the setup on the software
user new Thanks for watching. Yes I wil make a video about that some day :-)
Yes, alll function is O. K., cam program is running, only Jog function is not working,
Ok, what software do you use?
Hello,
I have built a CNC plasma cutter (MPCNC with GRBL control) and also use it with the Universal Gcode Sende program, but I have the following problem: The file has a length of 100mm, for example, but in reality it cuts me out to 300mm approx. All values in UGS are converted to mm (G21). What could be the reason for this and how can I correct this error?
Please send me your feedback as soon as possible!
Best regards
Tobias
Hi, the only thing I could think of is that you might have your settings, mm per rev, wrong
Check how far it moves when you tell it to move 10mm in joging function in UGS, measure how far the axis travels in real life. If it moves to short or long, you have to check over your travel settings to make the axis travels the lenght you ask it to travel
Try to follow my steps in the video 8:20
Thanks man 🤙
sir where can i download this version of ugs that u use? thank u
I think this problem in LaserGrbl v3.014 softwear setting.
You can check in above laserGrbl in menu /Grbl/Setting/Jog Control /Grbl/continuos Jog.
on/off Button has side to continuos Jog.
Maybe on position is jog work. And off position Jog not work.
I will checking at home. This time I am in office.
Hello...what to change on my gbrl settings on LaserGbrl software to achieve 50x50 cm engraving area on laser machine.When I downloaded Laser Grbl to exchange Benbox I uploaded one hex file as firmware.This is for some other machine and I have movement 30x30 cm.I want 50x50 to have engraving area.Machine which I have is 65x50 3w laser
Hello, I'm afraid I can't help you. Not familiar with laserGRBL
Hello
You told here (Video Minute 4:18) from the limit switches and that you come back to these in a lter Video.
Does this information about using limit switches with the arduino exist in one of your Videos?
I doesnt find there it in you Videos!
MiJabe Hi, thanks for watching my videos. I have not gotten to making the video about limit switches yet. I will do it in a future video 👍
what about setting soft limits and home?
Have you done it?
@@WillysGarageNorway I set all the speeds and did the calculations to figure out travel per step just like you did it. Huge help by the way
@@WillysGarageNorway but im not sure how to set up home and limits for the machine to move the table around the spindle
Hello, how can'I change xy length in grbl?
i am stuck help me ...........
i am making 5 axis cnc milling machine
by using arduino mega 2560 +1.4 ramps board
i uploaded frimware but the E0,E1 is not giving output as Axis A and B but when i am switching it in 4 axis in grbl foam cutter then it gives E0 as Axis U so ....
my problem is that i my board E0 and E1 which is not as Axis A and B ...... how and what changes i have to make in frimware to get This E0 and E1 as Output Axis A and B.......
>>>first off all i have to make changes in c++ files and header files then...
>>>second how i have to compile it in one single .ino file from bunches of c++ and header files of frimware
Atleast help me out from my second problem because i don,t know how to make firmware for my machine into single .ino files to upload it in my machines...................
please if somebody knows kindly help me to make it solved............
Hi. Very nice video. One question - is there a way to add 4th axis to arduino + cnc shield with GRBL? If not, what is the easiest / cheapest way to move to something else that can use 4 axis? Thanks
Awesome Video Series - Thanks for sharing this... I'm strongly considering building one and this is extremely helpful and really inspiring....
Ken Mais Thanks a lot, your feedback is appreciated :-) There is nothimg more fun than building your own machine and get it working. I'm glad my series helps you and let me know if you need some advice.
Sir how to provide set home position and home command to each stepper motor
how can I set up the core XY configuration? and how can I add a servo on the pen and control it with the UGS
jonathan sidon I'm not sure but I have heard about people using the enable pinout to activate pen up/down.
How can I increase the speed rather than using codes like $110 $111 any other method?
You can use all kinds of inputs. What do you plan to use it for?
@@WillysGarageNorway cnc writing machine
@@abrarmuqheeth1278 the speed can be set via the g codes. The speeds you set in $110 and on us only the maximum speed. So the speed is set when you make the g codes or the toolpath
@@WillysGarageNorway thanks
@@WillysGarageNorway James Munro dieselphiend hey buddy how can I achieve slowest and smooth one rotation per minute with maximum torque ? Using nema 23 with tb6600 driver ??
Please reply😢
Here is a problem to my CNC grbl with stepper motor that the response time, I send the command to stepper motor but it doesn't revolve it revolve when I reset or close the grbl and again open or linked up with arduino then the stepper motor runs with the previous code which I upload but it does not revolve at that time
I am also change the response time to one
What is the solution please tell
Very helpful video. Set up my machine, but just cant get the router motor to start!
Hi, sorry for late response. Do you mean that your spindle wont start?
Hi,
My cnc jog options is not work,
Plz tell me which parameters set in my grbl candle
Hi, does the CNC work at all?
This helped me out. Thanks for posting!
No problem, thanks for watching 😁
Hello, while processing the g-code file I created with UGS in CNC, the CNC axes go to the place they need to go very fast when the carving work of a point is finished and trying to go to a different point (idle acceleration), which causes tooth skipping and the coordinate is distorted. I wonder if I need to adjust the grbl settings or the g-code file to reduce the speed of the axes in these transitions (idle speed).
Brother help me my cnc machine is going to program and suddenly stopped and showing grbl 1.1h for help.. What isse Peressist I have no idea
Sound like a wiring problem if it suddenly stopped
@@WillysGarageNorway ok thanks
@@WillysGarageNorway brother I'm not happy waste my money and time I'm so upset my machine is now Dustbin. My dream is not true 😕😕😕 I'm not lucky
Sorry to hear that, good luck
@@WillysGarageNorway my dream upset 😕😕
I have the same problem. With settings $100,101,102 at 100.000 my Mill moves 25MM when asked to move 100MM. My thought would be to change to $100= 400.00, but that does not work.I also get noise and little movement. My machine is a cheep Chinese 3018 PRO. Is there another setting that needs to be changed?
Is acceleration that slow really necessary? I have not yet set but I'm wondering if setting mine to 200 would be bad. It's a 4mm pitch per rotation lead screw, and if I stall the motor, even at full speed the weight of the gantry can't move that lead screw.
Eugen Krause it all depends on your setup 👍
what optimum value for speed stepper motor, because when we set to fast the torsion become weak...
when i press $30 it says error invalid statement
my spindle stopped working all of the sudden
I need more info on the machine, spindle, vdf, controller boar and so on
@@WillysGarageNorway spindle 775ER
its the spindle that comes with the cnc 3018 pro same with the board
Brilliant Mr. Willy! I just connected my first stepper to my machine as a test and its agonizingly slow! How do i fix it? Why just watch Willy's CNC part 12 of course! Thanks again for making it so easy!
Chris comeau And thanks again for watching !! :-)
Thanks Mr Willy,that's very helpful as always,I have question about the values of $110-$112,how would you know the values to set ? is it based on trying or based on calculation?
Mohamed Amine BIDA Thanks again. You can increase gradualy 110-112 after you have found the step/mm (100-102). Increase it until the stepper «stalls» or you dont want it to go any faster. Then you can decrease it 10-20% to perserve your steppers. The same goes for the acceleration setting :-) Good luck and appreciate the feedback ;)
thank you
Very helpful, clearly explained, thanks!
No problem and thanks for watching 😁
why did they take the parameter name away from the $$ list? If it ain't broke don't fix it...
How to use 4 ieme axes on grbl?
Hi
i'm working on DIY cnc router project but i have a problem with lead screw or ball screw it's expensive man i spent about 650$ for stepper Nema 34 and other stuff
The question is Do you think if i use a belt my machine will be fast or what ??
Eng.Mudar A I dont think the machine would be any faster with belts. Belts are prone to wear and tear, they will slack and start missing steps and stuff. With the nema32 And 23 I would recommend going for some ball screws even if they are expencive. You can also do lead screws like me. Belts would not cut it, sorry
Thanks willy
Please if you have a time take a look to this video
He is using a chain to move the gantry
ruclips.net/video/x-tDJAon3Ag/видео.html
Eng.Mudar A Hmm, not a bad idea. But I wonder about the backlash in the chains and sprockets. Maby its fine :)
Hi, friend!! Excelent tutorial!! Just one question: why my Arduino don't save the parameters? I'm using grbl controller 3.6.1.
TreCe Robotics Hi and thanks. Doesn't it save setting when you change it in UGS?
WillysGarageNorway Yes, right. The UGS don't save the changes. I think that is the EEPROM of ARDUINO or my Arduino is wrong. The tb6560 is good.
Thank you! Really apreciate it!
No problem, thanks for watching
Controlling parameters disturb for jog function
Thank you very much
And thanks for watching 👍😀
When give g code manualy , error: undefind feed rate. How fix this error
Just COMMAND F100
ANYTIME LIKE F0-1000
I installed limit switches... And when it is pressed motor stopped working but after that I need to restart everything....and it's not accepting any further commands.. is there any option to move the axis away from the limit switch automatically after it is pressed...
Great video. Thanks man :)
Thanks 👍 :)
Thanks , but when i try to change ($101=400) the stepper make a high noise and not moving, why ?
My stepoer nema 23 ... 2A
Thanks
That means 400 steps per mm. Does your stepper have 400 steps per revolution? anyway you have to make these settings smaler when doing that.:
$110=2000.000
$111=2000.000
$112=2000.000
I have the same problem. With settings $100,101,102 at 100.000 my Mill moves 25MM when asked to move 100MM. My thought would be to change to $100= 400.00, but that does not work.I also get noise and little movement.
Sir,Please snd the download link of universal gcode sender
Anuj Singh Hi, check this out:
winder.github.io/ugs_website/
Grbl control (Candle)
I have no experience with Candle. S, Im not the person to help you with that. I use the Universal G code Sender
is this setting written by me ? or it's written by the same program?
majick talent What program do you use? This settings are written in the GRBL code for the Arduino
WillysGarageNorway
I use grbl controller or universal Gcode sender ...I don't know how can I setting this programs 😣......can you help me ? Please 🌿🌹🌿
majick talent In this video I explain how you figure out and adjust the GRBL settings using the universal gcode sender. Hope it helps you
WillysGarageNorway
I hope that too ....
thank you for evry thing...
Hello sir
I used universal sender but i browse small gcode than is work properly but i download some g code like image but after browse universal send show empty file and show just complet 00.00.00 sec plz give solution plz sir
Hi, IT sounds like the gcode file is wrong or corrupted somehow. Have you tried another gcode?
WillysGarageNorway g code file is correct
WillysGarageNorway give your gmail id i send video of my problem
ok, you can send me mail at wgn@willysgaragenorway.no
Excellent. Thanks for this.
No problem :) thanks for watching 👍
Very nice very helpful video🖒
Thanks for your feedback :)
SIR PLZ HELP ME TO CALIBTRATE MY MACHIE
What kind of machine do you have?
simple just follow the instructions
Hello sir
I am using nema23 with tb6600 drive with 24 volt 10 amp, but with 32 micro stepping my motor rpm is very low around 30 or i change it into 1micro stepping then its rpm is around 150 with vibration
I am trying to increase rpm of my stepper motor with smooth running
Please help me....
Tushar Gajbhiye Hi sir, it sounds like you have to change the $100 $101 and $102 setting on the Arduino. This setting changes when you change the microstepping on a stepper motor. If you have a 0,9 degree motor and use full microstepping (fullstep) your stepper must have 400 steps per revolution. Then if your leadscrew travels 2 mm per revolution this value should be sett to 200. That means that the stepper motor travels half a revolution for the cnc axis to travel 1 mm.
Hello sir,
My motor have 1.8 degre & if i change $100,$101 and $102 setting more than 300 value then my motor stop rotating and make loud noise and after noise decree then motor little rotate and stop
Tushar Gajbhiye do you use a leadscrew or belts?
Sir,
I am using Ball screw Dia 12 x 4 Pitch
Tushar Gajbhiye With a pitch of 4mm, that means the ball screw moves the axis 4mm/revolution. In the GRBL you want to input the step/mm. You have a 1.8 degree stepper wich needs 200 step/revolution. That means in fullstep mode: (200step/4mm)=50step/mm
In half step mode: (200step/4mm*2)=100step/mm
So, first of try to put $100-102 setting in fullstep mode to 50step/mm and test the machine
Nice video, thx
Thanks, no problemo:)
hello this configuration is valid pear NEMA 23
Its valid for more steppers and lead screw/belts if you follow the instructions 😁👍
Thanks A lot..
No problem :)
Helpful..
Thanks
No problemo:)
Thank you Best regards
No problem 😀 thanks for watching 👍
How to fix Z axis to 0
If you want to know how to set zero on the axis befor starting a jobb, watch this video that might help: ruclips.net/video/A1zlL3q23HI/видео.html
Thanks Mr willy
@@djl7085 no problem, did you figure it out?
May ask for help for Indonesian language I really need this way
saiya rodok setres Hi, I’m not sure what you mean?
WillysGarageNorway pls give subtible indonesia because i see subtible inggris only
saiya rodok setres Hey, I dont know if its possible for me to activate indonesian subtitles, but I will check 👍👍
nice job :) i'm doing the same with my cnc :P
Thanks :-)
awesome work! Thank you so much!!
Thanks man :)
Thanks lad ;)
Ben Frawley No problem :-)
you are great
azeem khan Thank you very much!!! :-)
Direction error
Maathav Rajan Hi, what do you mean? :)
Now it's ok thanks 👍👍
meget bra takk
Thanks Mr Willy,that's very helpful as always,I have question about the values of $110-$112,how would you know the values to set ? is it based on trying or based on calculation?
Hi and thanks :) You can calculate this value somewhat, but i depends on what drivers, steppers and PSU you have and use.
So it's recommended that you increase this value until your stepper motor stalls and then decrease the value about 10-20%.
This is so your system doesn't run on 100 % all the time :-) Did this answer what your question was about?