FPV Drone simulator using Arduino and Flysky Transmitter | Unojoy Joystick | without simulator cable
HTML-код
- Опубликовано: 7 сен 2024
- Enjoy flying a drone without actually having it!!
Arduino Uno : amzn.to/41eVm5A
Download Files-------------------
JRE Flip Installer: drive.google.c...
Unojoywin Zip file: drive.google.c...
Circuit diagram: drive.google.c...
FPV game link : drive.google.c...
AtLibUsbDfu.dll Error Solution video : • AtLibUsbDfu.dll not fo...
--------------------------------------------
Tutorial links🔻
Steering + Pedals using Mouse : • How to make gaming Ste...
Steering + Pedals using Arduino Uno: • Arduino UnoJoy Steerin...
Sequential Shifter using Arduino: • DIY Sequential Gear sh...
H- Shifter : • Homemade H-shifter fro...
---------------------------------------------
Music🎶
Adventures by A Himitsu / a-himitsu
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
Free Download / Stream: bit.ly/2Pj0MtT
Music released by Argofox • A Himitsu - Adventures...
Music promoted by Audio Library • Adventures - A Himitsu...
Song: Markvard - West Coast (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • Markvard - West Coast ...
-----------------------------
Follow us on Instagram :
/ tech_at_home
Like us on Facebook :
/ tech-at-home-220885266...
Thanks for watching!
Like Share and Subscribe
#FPVFreeRider #techathome
EXACTLY WHAT I NEEDED! THANK YOU SO MUCH!!!
Edit: I had to check out the rest of the channel and this is easily the most recent underrated channel I've found, please keep doing those cool projects, I'm going to go and binge watch everything here 😁
Thank you so much, for your support!!!
The quality of content is so is just amazing
Keep posting videos you will be successful soon
Thanks!!
when i calibrate it the stick on the right wont work correctly the i make it to go to the left it doesnt work (it doesnt show any signal) but if left it shows a signal, if i make it go up and down it becomes the right and left in the game, PLEASE HELPPPPPPPPPPPP
bro i have done everything in the video but not responding when i move the joystick stick
Dear sir can we connect esp insted of cardino if you could help me with that i we be graceful . hope you will reply
No , the firmware used support only Arduino UNO board.
When I try to open TurnIntoAJoystick I get the error message "could not find a Java virtual machine, cannot continue" from flip and I cannot fix it, what do I do?
Very good my friend . Tell me if i want to put joystick convert it from usb to ppm out singnal into my trainer mode radiomaster tx16s
When I run the batch file, I get this error: Could not find AtJniIsp.dll
But this file is already in C:\Program Files (x86)\Atmel\Flip 3.4.7\bin . How do I fix this error?
yes even i got the same error please help me how to fix this
or just use old mouse cable and audio jack for PPM cable to your mic-in...
while running turn into joystick, it shows "operating port failed" a firmware was not found. rest all is pass
Did you change anything in the file location?
@@techathome nope..
I just followed the steps as same.
But, while running "turn into joystick" two error popup is appearing.
Can u uninstall Atmel Flip,
And reinstall and try
atlibusbdfu.dll not found this error appear when i run the TurnIntoAJoystick file .. please help
Refer this video: ruclips.net/video/Vd0F0XHzchY/видео.htmlsi=c9C0wdlRuHCQMA5q
i followed the same method but during the calibration of the controller the roll is not working
mee too
hey I'm usuing radiolink at10 2 and r12ds rx which does not have ppm
i want to know how to do it for pwm or sbus
I have not tried that, is there any other code files other than ppm, inside the given folder??
@@techathome no but I write code for pwm and it's works for 6 ch
Which is enough for me
make video to use with esp8266
Yes sure
is possible use PWM 6 chanel ? i have no ppm
No
Bro my receiver only 6 output pins how should i connect with that
Which is the receiver,
Can u mention the name.
Bro is this work on ct6b transmitter? Kindly reply me soon
Check if you have PPM output on the receiver?
I don't think CT6B supports PPM mode.
deos this works on a rc car remote as well?
Can you share model name
It should have PPM output on the receiver
hey i wanna know if i can do the sxame with a arduino nano
No not possible
@@techathomecan I do using a nano shield
No
UnoJoy joystick dissappear from control panel when i turn on the remote , when i turn off , it reappears, what can be the problem ?
Thanks in advance
i found the problem , i was powering the receiver with arduino , the current wasnt sufficient from my laptop, so i powered the receiver externally and now its working fine . thanks for the content, god bless you
Thanks for solution, it will be useful for others
I have flysky ct6b how can i enable ppn output
That receiver with ct6b doesn't support PPM output
AtLibUsbDfu.dll not found. Brother I have this error. i am not able to run bat file. What should ı do. Can you help me ?
Here is the Solution video: ruclips.net/video/Vd0F0XHzchY/видео.html
@@techathome I watched. But still I have same problem. I’m using arduino uno ch340. I want to use simulator with this ardunio.
You cannot do this because,
Ch340 doesn't have option for enabling DFU mode( direct firmware upgrade)
Thank you for helping me
Im using Fly sky ct6b transmitter which does not have ppm so how do i use it?
For ct6b you will be having simulator cable right. You can use that only.
@@techathome No the cable does not work with ct6b models, that cable is only used for firmware updates.
In the code there is a boolean for ppm I can make that false but i dont know the pin numbers for other channels
@@yashc7562bro how you done this in ct6b
bro can we do this with esp 8266 and ct6b transmitter
No
bro the folders in the discripion are doucuments.
you cant install them
All links are working fine. I have re-checked.
not getting pass message
pls help
What is the error
nice tutorial deepak and deenu anna
Thanks
not working for me i am not able to run bat file
What error are you getting??
I have arduino nano, is this the same procedures to connect it
Arduino nano, you cannot do it
Can you please helpe to connect arduino nano to my laptop, thanks you in advance ❤️
In Arduino nano, this project will not work
Great job 👍🔥🔥😍
Thanks
Big like friend ❤❤👍👍🙏🙏
Will it work with windows 10/ windows 11
yes
Which is your operating OS system
windows 10
Bro Arduino code error
What error u are getting? Full error message can u send
Nice info bro
Thanks brother