How I Cleaned My Halo Swivel Bassinest
HTML-код
- Опубликовано: 3 июл 2020
- Instagram
@_mrsbrandy
Business Inquiries: msbtrendy.yt@gmail.com
*email address is subject to change as I am currently in the process of a new channel name. Information will be updated once a new channel name goes into effect.
All opinions and products I used are my own. I purchased this second hand and wanted to share how I was able to deep clean the Halo Swivel Bassinest. Prior to washing it was in decent condition (no moldy spots). This is the Halo swivel bassinest that was made in 2017. I knew the year because of the sticker that was on the inside (after removing all fabric).
Products I used to sanitize and clean the fabric: Hand vacuum any loose debris or dust. Then a steamer was used to steam all fabric, including the mattress. After the steam process, I washed the fabric by hand in 3 washes. Using vinegar and warm water solution, pyrex and warm water, then baby detergent and warm water. The mattress can’t be washed, only wiped down (according to Halo website). I was very gentle with the fabric while hand washing and ringing out the excess water. Air dry the fabric and when everything was dried, I put the fabric back on the bassinest. I also left the mattress out in my living room so it could air out. I wouldn’t suggest delicate cycle in machine.
Level of difficulty: Moderate
Tips that helped me: Take my time and be very gentle. Handwash fabric, no machine wash or delicate cycle. When assembling and removing fabric and side bars, always make sure both sides are balance or inlined with each side.
Step 1: Hand vacuum any loose debris or dust and remove mattress.
Step 2: At the inside of the bassinest, open the slit that has the Velcro.
Step 3: Using a screw driver, unscrew 6 of the screws halfway out and remove from base.
Step 4: Remove front and back bars. I used a screwdriver to help me press down the tabs at the front and back bars.
Step 5: Remove both side panels by pressing down on tabs.
Step 6: Unscrew the 3 screws at the middle base connector. Kept my screws in a place that I would not lose them!
Step 7: The 6 screws are still attached to the board. Remove sleeve by lining up the side panel, and carefully pull back and slide one side of the sleeve.
Step 8: Once fabric is removed. I hand washed the fabric (see “Products I used to sanitize and clean the fabric”).
Assemble back together…
Rewind what you did to remove the fabric.
Step 9: Lay fabric flat on ground. Insert board back into fabric with sticker facing up. I like to say it’s like putting on a coat, start with one side and then finish the other side. Also, line up the fabric with the side panels just as it was done in Step 7.
Step 10: Screw 3 screws back and insert the other 6 screws. The fabric needs to lined up with the holes.
Step 11: Line up the base and attached to the 6 screws. Make sure it is locked in.
Step 12: Screw 6 screws. Do not make screws too tight or too loose.
Step 13: Base should be secured and able to put back onto to stand.
Step 14: The Slit’s velcro should be put back into place. To ensure the fabric is assembled the right way, the Halo Bassinest logo should be facing you.
Step 15: Insert side panels and side bars. Side bars were difficult for me to put back so again, I used a screw driver to help press down the tabs. Put remaining velcro parts together.
FTC: This video is not sponsored. All thoughts and opinions are my own. Some links in the description box are affiliate links. I receive a small percentage of the revenue from purchases made through the affiliate links. 
Хобби
Thanks so much for this. A great way to spruce up a secondhand find. I put mine in the delicate cycle to wash and then air dried it. The netting did catch a bit on the velcro, so make sure you attach your velcro before washing, if you're reading this!
Thank You!
It’s been 2 years since your comment but wanted to let you know, you’re still helping us to this day! Thank you!
@@brittneyhenderson2494 I second that!!! I just bought one secondhand for my baby due in September :)
It is CRAZY how difficult they make this product to clean. Thank you for making this video.
Something that helped me struggle less was removing the side plates before taking out the metal rods that helped a lot!
So so helpful! I was bummed when I first brought home my used halo that the fabric wasn’t easily removable for washing… but I walked through your tutorial step-by- step and it saved the day! Thank you!
Thank you SOOO much!! This was wildly helpful!! I’d say my only “issue” was in reassembling I had trouble getting the small round piece with the three screws put in after already wrapping the fabric around the wooden bassinet base, so I took it off and screwed in the small round piece first (I needed to get my hand under the fabric to guide screws to the holes) and then wrapped it all the way around!!
Also a tip for anyone interested: I got mine second hand from a friend and it was stained a bit of an orange color - but I knew where it was from so wasn’t concerned with it being gross - however, soaking/scrubbing with 1/4c hydrogen peroxide mixed with 1/2c dish soap and then letting it dry in the sun after thoroughly rinsing got out all the discoloration and it looks brand new!!
Thanks so much for this video!!
Did you have trouble getting those 3 screws to tighten back in? Mine just keep spinning and I’m not sure if that’s because I stripped the wood or not
This video was just what I needed, thanks so much. I will say that I put mine in the washing machine and dryer. I used the setting delicate and everything came out fine.
Omg thank you so much, I'm 33 weeks and hand washing seemed like too much 😂😂
Thank you! 28 weeks pregnant and I had mine mostly taken apart when I heard the handwashing part and instantly regretted taking it all apart😅
Same! It was all fine!
Thank you. Still helping others with this info. ❤
I would honestly Machine wash cold, gentle cycle (only use warm or hot if it's heavily soiled!) Then I would just hang dry to protect from wear and tear. It only takes an hour or so to hang dry, even though it is currently chilly where I live.
My first daughter was a refluxy baby, so when I brought my halo out of storage for baby #2 it was covered in yellowed stains from spit up. Your instructions were super helpful to take it apart. I washed in warm water in the washing machine with tide and oxy clean and let air dry. Then reassembled and let it sit in the sun for a few hours to brighten it back up again. Looks like new!! Thanks!
Thank you so much from the UK. Just got a bassinest for free from a lovely lady and now I am on a mission to make it perfect for my little bean! You are so helpful! xx
We bought a second hand one and so glad I stumbled on this video. But dang that’s a lot of steps 😳
I just did it... it’s really not it’s 11 only screws. It was a breeze! Listen to her “tips”! It’ll save you a world of trouble and time!
Thank you so much for sharing! Can't believe they made it this difficult. I read others comments and put through the washing machine on delicate by itself, then air dried (doesn't take long) and it turned out fine!
Just finished washing our second hand bassinet thanks to your video. We washed twice on the delicate cycle and dried on low and everything came out ok.
This was extremely helpful! I felt so comfortable taking everything apart because I knew I could get it reassembled without worries!
Thank you so much! Video was super helpful. Lining up the 3 piece are not bad you just have to make sure the cardboard base is lined up the right way. I stuck toothpicks in the cloth and holes to make sure it was lined up when I placed the 3 piece then removed them one by one as I screwed it in place. Attaching the big swivel part was definitely harder it took me a few tries but once it was aligned it was a lot easier to put into place. One thing I also found easier was when attating rods A-A and D-D for example making sure they both are in their holes at the same time made it quick to snap them in place versus doing one side at a time. I hope this helps someone else. I noticed in the comment section lots of people struggling. I washed mine with Dreft baby detergent in cold water on delicate in the washing machine. I made sure to let it soak for about 20 mins to remove any odors but thankfully mine was like new, no stains, it just had like a household food odor from the people I purchase it second hand from. So happy I came across your video. I lysoled the mattress and let it air out but I think I’m still going to purchase the dreamweave replacement mattress and the snuggle me newborn insert. I really want my baby to like this bassinet 😭. considering I only paid $40 for it and even with purchasing the accessories I’ve still spent less than if I would have purchased it new. What made me comfortable was knowing i could take it apart and wash it.
Thank you for this! I just got one secondhand too and once I got it home I really looked at it and it is dirrrtyyy. Yours was the only video I found!
Thank you for this super helpful video - it is a lifesaver! I never would have figured out how to take this bassinet apart to clean it and put it back together without your instructions. Thank you again!
Omgggggggg this is amazing!!!! We stored our Halo (covered) for the last year and a half after using it for our first child, we pulled it out bc we are due soon with our second and I just feel like it needs a good clean! Ty!!!
My husband and I just purchased one second hand and are so grateful for this video! Thank you so much for the step-by-step process!
I ended up putting in on delicate in my washer and it came out perfect. I just let it all air dry in the sun/heat. This video helped me so much in how to assemble/disassemble. Thank you
I'm so glad I found your video,..unfortunately, I put mine back together backwards (it had the music and vibration box on it) and had to retake apart and reassemble. I ended up washing it 5x's and using a spray bleach on a stubborn spot, and let it airdry. I appreciate how calm you stayed thru the entire video!! Unlike me!
Just followed these instructions. Currently soaking the cover in Oxiclean & detergent. Will report back on how it goes. Really appreciate this video. Very helpful!
how did it work
Thank you for this video! Your instructions were so informative and clear and helpful! very good job putting this video together with clear and concise steps! you are are awesome!
Took mine apart to store it and now need it again. Thanks so much for this video. Now I can put it together again!
Awesome video. I tried it. Works ! Removing the arms get very easy if you push the locking pins inside with a screw driver. You can pull it out easily later. Also, pulling out left and right sides of the arm together works
This is one of the best explained videos that you will find. Thank you
Thank you for making this video. It took a little searching but I found you. I got stuck putting it back together and your video helped me complete the steps.
Thank you so much I didn’t know what I was going to do if I couldn’t wash it because I also got it second hand!
Thank you for making this video. I bought mine used and noticed when I got home that the fabric had little dog hairs and old spit up in the crevices under the mattress. I just couldn’t imagine putting my newborn in that 😬 now it’s like new again! I wasn’t able to get the circular piece that screws to the bottom of the bassinet back on but it seems to be okay with the screws holding it into place.
Thank you so much for doing the great detailed tutorial! I was able to wash my halo bassinet and reassemble it before selling it! 🙌
You’re a lifesaver for making this video. Thank you!!
Thank you SO MUCH ❤❤❤ You explained it very well and everything went perfectly for me, no damage to the factory 🎉
This was very helpful!! I cleaned mine following your instructions and adding a few things and it looks like new!!. Mine (also a used one) had a very bad brown stain around the base, so I had to use a bit of OxiClean spray to remove it with a toothbrush, as well as vinegar mixed with pure baking soda and warm water. I then put in the washer with a bit of baby soap in delicate, cold cycle and air dry it. Thank you for the video and congrats for your baby!! :)
Pilar Valencia yay! Glad it helped! Thank you
Yes ours too! I dont know why other than the "wood" board isn't sealed so it must rub off on the material.
This video helped me so much, I struggled at first because I only removed four screws instead of six! Once I figured it out it came apart easily!
Forever grateful to you for making this video! It could have been so much harder otherwise 🙏
This is the most useful video I have ever seen on RUclips.
Thank you! I got a used one too and it’s desperately needs a deep cleaning!! This is very helpful!!
I can’t thank you enough for making this video. My daughter is expecting my first grandchild and she really wanted a halo so we found one second hand and I was able to was and disinfect every part thanks to how informative your video was!
Just purchased a used one for a good price. Will be buying a new matttress tho. I will attempt to take it a apart to wash because I have a small brown spot on mines and I refuse to just wipe it down. I've read you cannot take the fabric off but I see that's not true. Thank you for this great detail video.
Thank you so much for this video! I’m so happy I can clean it 😇
Thank you so much for this video. I forgot how to put it back together! This video was much needed!!
This was awesome! Mine came so clean. Thank you for posting and sharing.
Thanks for this! Mine was in storage and I brought it back out for my new baby and it had become dingy needing a fresh wash. I couldn’t figure out the final pieces to get it off so this was very helpful!
This was so helpful. Thanks for thinking of this post!
Excellent! Purchased one second hand and rim was nasty - life saver!
If you're struggling to align the bassinet base , just use 2 Allen keys to first align and keep the two nail free holes in place.
Thank you so much! I was struggling to the point of frustration until I followed your tip.
this is so helpful! i just purchased a used halo bassinet and am looking forward to cleaning it thoroughly with the help of this video thank you!
Yay! So glad this video helped you! After 2 months of using mines. I really like it and want to keep it for future babies:)
Yay!
Guys, you can use a washer machine on a cold, gentle cycle. If your washer is notorious for being rough on clothing, then see if you can try to use a friend's washer or laundromat. I wouldn’t use hot water unless it's very soiled, with bodily fluids or something. Then allow to hang dry. It doesn't take long. 1-2 hrs tops, and my apartment is chilly right now. For stubborn stains, hang dry in the sun, and the sun will bleach the stain out naturally.
Thanks for the video I also just purchased one today and wanted to wash even though its super clean and beautiful
Nomie Love yay!! I know what you mean. ;)
You just made my life so much easier thank you
Thanks a lot!! It was so easy to put it back together
Did you upload a video on how to hand wash the bassinet?
Thank you for making this video!❤
Thank you! My son spit up alllll over this so now I'm trying to deconstruct and clean it.
Thanks
Very helpful; I dried with a blow dryer to speed up reassembly
All I can say is THANK YOU ! 🫶🏽
This video was so helpful! It made cleaning our secondhand bassinest a breeze. Thank you for taking the time to film this!
Im getting ready to donate mine to a place that helps out young mothers... this video helps so much I wouldn't donate without cleaning it first
Do you think this can be washed in a gentle cycle in the wash and hang dry?
Thank you! Just the video I was looking for!
Thank you for making this! Very helpful!
Thank you for the video. One thing to note is that it's better not to remove the inner circle thing from the outer one when reassembling. I did that and ended up having a lot of grease in my hand. And then it became a little more complicated. Also, when trying to attach the mover thing to the base of the bassinet, aligning screws from behind with my other hand helped. Cheers 👍
Oh no - I removed the inner circle part and now cannot figure out how to reassemble. Did you find another tutorial how to fix this? Please help.
Gracias por tu ayuda 😊
Thank you for making this video, I just set mine up after putting it to wash. Do you know if I can find a new cover for the whole bassinest not just the mattress cover? Thank you
Thank you, this was incredibly helpful!
So so helpful!! Thank you!
So this video was a definite life saver; as I got a second hand one and it 💯 needed a good cleaning BUT I have been trying to re-assemble it for hours, almost in tears, with the hardest part being the center piece with the small screws. It appears I have the material lined up with the holes but when I go to screw in the centerpiece it doesn’t stay. I literally want to cry.
Same here! Did you ever find a solution?
Also having this problem. Did either of you figure it out?
I just washed and THANK GOD it got out all the mildew stains from sitting in storage. It looks and smells new!
I’m planning to air dry..how long should I wait?
Thank you! 🙂
Thank you SO MUCH! This was so helpful!
Thank you! I was given one and it is stained so I'm going to try and wash it
I might be getting a used one (not thos brand) but I'm hoping this helps
This was extremely helpful thank you !
Have u tried cleaning the 4moms bassinet i got it today used and its pretty clean but im not comfortable putting my baby in it if i don’t clean it my self
Thank you so much for this video 👍👍👍 I would’ve never figured this out on my own lol 😂
You nailed it
Doing it right now. Thank you so much
Thanks!!
I thought I couldn't clean it as it has screws everywhere. Thanks for this video ❤️
Super helpful. Thank you!!!!
Helpful video mine isn't used but I wanted to know how to wash it 🥰
Thank you. You really helped me.
This was very helpful!!!
anyone washed the mattress? i would like to know how to clean the mattress
Great video! Thanks!
Thank you will try this
Amazing!
When I go to put it back together none of the screws will tighten into the wood? Have I stripped them? 😢 They just keep spinning
Thank you so much very helpful video
How did you removed the bassinet from the base 😢
😊 thanks 🙏🏻
Thanks for this!
Okay just did this. Tip: when you go to reinsert the side bars don't click in the big plastic side pieces into the bottom of the bassinet. After 30 min I un did it all in frustration. Came back and tried again and the side bars went in easily and the big plastic pieces easily popped in on the bottom.
Anyone have trouble getting the 3 screws to tighten? Can't seem to get them back on 😢
So helpful thank u so much
Thank you! You saved me.
Thank you 😊 my bassinet is new but it smells funny.
KS I noticed a funny smell for the pad so I left it out in the living room to air dry for like 3 weeks and the smell isnt too bad anymore.
Hope I can do this with the twin Halo.
Thank u🙏🙏🙏🙏🙏
👍👍thanks!!
i was thinking i had to wash this entire thing with a toothbrush Lol. maybe i’ll try this! seems like a lot of work but i’m willing to try!