How i cut my rev limiter wire to increase speed on my 2016 Kymco Super 8x 50cc Scooter. Went from about 28mph to about 35mph just from disabling the rev limit.
@@Logan_Neasbitt i did the same thing id say it goes faster but like for me only adds 5kmh and it pulls up slower since it goes full rpm when you throttle. Go for a sport cdi that has no limit.
2023 Super 8 50x worked on as well. Going downhill.. DOWN HILL! would go to 32 then back to 30!, just this one change alone i hit 36. Next step is the malossi variator multivar kit and kevlar belt. After that probably 82 carb yet, then if still need more may look at exhaust.
Now the scooter does not reach full speed because the engine is getting too little fuel. Remove the carburetor and open the float bowl. In the middle is a copper nozzle. You can unscrew that. If the hole gets bigger, the engine gets more fuel. This can be done by means of a file set. For sprinklers.
The Super 8 has the gimped variator bushing, you can get them fairly cheap off of ebay. I did that to mine and got an extra 10km/h to my top speed. I'm scared to do any other modifications while it's still under warranty.
@@superleetmegapunx Mine is a 150 and it was not restricted by the variator bushing. I did get about 7mph top end gain with a Naraku race variator swap and some Dr Pulley sliders. Very simple mod. (WARRANTY IS EXPIRED ON MINE).
@@henrilopes7337 Mine doesn’t have any purple wires. The far left bottom wire is green, and when I disconnect it the bike won’t run. Mine is 2022 and I don’t know which direction to go in now. Thanks for the reply. I desperately need for this thing to go faster.
Adjust rev limter screw by front brake ....that will fix your throttle lag problem ...im no expert i saw somone else do it but i think its a safe assumption
@@Thomaat116 no it does not work. What you need to do it take a hacksaw and cut a notch on the opposite side of the wires down about 3/8’s of the way through the box and you should see a copper wire. After you hit that you should be good to go and have gained about 5-7 mph
I looked at a pinout on Google of 6 pin and it looks like one is the signal wire and one is the ground. So the two wires all the way the left if you are looking at with the smaller clip with two pins on your right. In theory you should be able to take either out. I would recommend just taking the pin out of the plug instead of cutting
Then you probaly only have a variator ring. Check if there Are any wires from the variator to the cdi. If there is cut it, if there is not a wire there you will need to remove the variator and locate a small ring and remove this. But buying a Racing variator for 50-60$ will be the best option and give you the most top speed.
bro the deer💀
Same 😂😅
Thank you so much for this. I was stuck at 30 mph and I only weigh 140 lbs. This added at least 5 mph on flat ground. (Kymco 2022 Super 8 50X)
And I got to be the 100th like on your video that has 14,500 views. People are stingy with that thumbs up button....
Bro you are a superhero my scooter was also painfully slow. I did the same thing as you and it is much better now thank you so much!
Is your engine holding up well
@@Logan_Neasbitt i did the same thing id say it goes faster but like for me only adds 5kmh and it pulls up slower since it goes full rpm when you throttle.
Go for a sport cdi that has no limit.
This worked I have a 2021 kymco super 8 50x and I cut the purple wire connecting to the CDI and it made me go from 30 mph to 35-36 mph
Yoooo... this worked. 5mph more for me. 7-8 for my girlfriend. Thank you!
Why the dears so chill 😂
2023 Super 8 50x worked on as well. Going downhill.. DOWN HILL! would go to 32 then back to 30!, just this one change alone i hit 36. Next step is the malossi variator multivar kit and kevlar belt.
After that probably 82 carb yet, then if still need more may look at exhaust.
Now the scooter does not reach full speed because the engine is getting too little fuel.
Remove the carburetor and open the float bowl. In the middle is a copper nozzle. You can unscrew that. If the hole gets bigger, the engine gets more fuel. This can be done by means of a file set. For sprinklers.
That deer made me like the video
Also did you do any modifications to the bike?
İ cant find the ecu on my like 50 2021 😊 do you know that how can i find? Where can be there?
Ever happened that it went in like a safe mode after that… and cutting the power like in half?
Hi guys i have a 2013 super 8 8 pkug but there is no purple only a pink an black mix
Is that bad for the engine long term?
Would this work for Super 8 2T?
So funny the deer watching you
nice lincoln ls is it a v8? 3.9
I have an identical scooter with exactly the cable that needs to be cut.
Some of these have a restrictor bushing by the variator--not sure of the Kymco.
The Super 8 has the gimped variator bushing, you can get them fairly cheap off of ebay. I did that to mine and got an extra 10km/h to my top speed. I'm scared to do any other modifications while it's still under warranty.
@@superleetmegapunx Mine is a 150 and it was not restricted by the variator bushing. I did get about 7mph top end gain with a Naraku race variator swap and some Dr Pulley sliders. Very simple mod. (WARRANTY IS EXPIRED ON MINE).
Casually has Bambi in the yard
You said that there are 2 different purple wires. Exactly which one is the rev limiter ?!?
Either one of the purple wires will work. I cut one yesterday, went from 28 mph to 35 mph max speed
@@henrilopes7337 what year is yours?
@@joelalexander5338 2021
@@henrilopes7337 Mine doesn’t have any purple wires. The far left bottom wire is green, and when I disconnect it the bike won’t run. Mine is 2022 and I don’t know which direction to go in now. Thanks for the reply. I desperately need for this thing to go faster.
@@joelalexander5338 lemme know when you find out. About to buy a 2022 tomorrow
Adjust rev limter screw by front brake ....that will fix your throttle lag problem ...im no expert i saw somone else do it but i think its a safe assumption
👍👍💯💯
I did in it work I go like 34
Will this work for a regular agility 50?
I need this answer too xD
@@Thomaat116 no it does not work. What you need to do it take a hacksaw and cut a notch on the opposite side of the wires down about 3/8’s of the way through the box and you should see a copper wire. After you hit that you should be good to go and have gained about 5-7 mph
Which one of the purple wires did you cut? I have a Kymco Super 8 and I didn’t know which one
I'm here for the same question
Same question
I looked at a pinout on Google of 6 pin and it looks like one is the signal wire and one is the ground. So the two wires all the way the left if you are looking at with the smaller clip with two pins on your right. In theory you should be able to take either out. I would recommend just taking the pin out of the plug instead of cutting
@@thomasd2695 yanlis olan pembe kabloyu kesersek ne olur
Either one of the purple wires will work. I cut one yesterday, went from 28 mph to 35 mph max speed
Those deer would like to know if this is the droid they're looking for
My super 8 50 goes about 37-40 if I were to do this would it make a difference at all?
looks the same as a DJ50s one.
Do you know what wire to cut on the dj 50s?
I have a tomos nitro my max speed is 25mph
Same lol. Love det lil bitch
Venison for lunch
Lot of deer 😂
I thought they were fake for a second
Very upset because you don’t show which wire to cut
A purple one. You can also google the wiring diagram and cut it yourself. If you don’t know which one to cut your better off letting it be.
Unn
Jnmi
6m7m
if you only have a 6 pin one cut the pink wire
What of i have 4?
Then you probaly only have a variator ring. Check if there Are any wires from the variator to the cdi. If there is cut it, if there is not a wire there you will need to remove the variator and locate a small ring and remove this. But buying a Racing variator for 50-60$ will be the best option and give you the most top speed.