How To Build A Firewood Storage Shed In One Day / DIY Firewood Shed / Firewood Rack Build
HTML-код
- Опубликовано: 31 май 2024
- Plans For The Firewood Storage Shed: etsy.me/3LkTtuE
Artisan Made Truckers Cap: etsy.me/3qIwqT4
My Etsy Shop: etsy.me/3qgDnr8
In this video I will show you how to build a firewood storage shed in one day by yourself. This shed will easily hold one cord of firewood. My main objectives in this DIY project is to build a firewood shed that will last many years as quickly as possible, while spending as little as possible. This project took me 12 hours to build and film. Had I constructed this shed without recording, I would have been able to build it in about 9 hours. If I had a helper, I think I could have built it in less than 6 hours. If you want to build one of these quickly, purchase the plans in my Etsy Shop and you will be on your way to building a perfect home for your firewood.
Links to Materials Used:
2-inch decking screws - amzn.to/3LcV70Y
3-inch decking screws - amzn.to/3NdHkbY
2 7/8-inch structural wood screws- amzn.to/3LaLrEr
Corrugated roofing screws - amzn.to/3MeZKZQ
Corrugated roofing - Roofing supply store or big box store
Metal Cutting Shears - amzn.to/3lqppDn
Artisan Made Truckers Cap: etsy.me/3qIwqT4
My Website: www.artisanmadethings.com/
Follow: / artisanmadethings 
Хобби
That's a good-looking wood shed. The tool person in me would use that as an excuse to buy a pneumatic nail gun 😂.
A good trick for making a wood shed is to put a divider in the middle... that way you can put next years wood in one side to allow it to dry properly while you use up the other side. Then switch around every year.
I needed to build a wood hutch for are firewood. I like your idea about dividing it in half. So, It's 8 ft by 8 ft with a divider in the middle. Thank you. 😊 It looks nice.
Your use of clamps is truly inspiring.
Thank you! Only out of necessity.
Thanks. Another tip is the roofing screws are meant to go in the hill and not the valley of the corrugated roofing. The trick is to not over drive the screw and bend the roofing. Living in Australia where this sort of roofing is very, very common, it is how it is installed here.
In Denmark all of this type of rooftiles are screwed in the valley of the tile... I thinks it's funny how much deffirence from each country there are in building style.
@@Soruotr I am ignorant, so no arrogance here, but I would think that having the screw in the valley might collect a bit more moisture when those rubber washers age and potentially crack.
All screws are ment to go on the hill. So water flows in the valey and not in the screw hole
When I did corrugated roofing, the screws instruction said on the top of the ridge. When I did metal sheet roofing, the screws instructions said to put them in the flat area, next to the ridge. From what I could see, the screws were the same so it appears to depend on the style of roofing.
@@Soruotr no matter where you live, the smart thing is on the hill, instead of where all the water will go
Turn the roof upside down and re- screw it using the same holes. You'll be able to reposition the sheets and the screws will be on the high points of the sheets. You're welcome.
Though I will eventually build one of these I am more impressed with some of the other ideas I managed to pick out in your shop and some of the constitution ideas. Great.
I built this plan this past week, and I'm really happy with the outcome. Great plans on Etsy. I did two edits from the original plans: 1) I put it on 16"x8"x4" concrete blocks, and 2) I decreased the number of floorboards from 9 to 7 (allowing a 1.85" gap between each). I also had to sub 8' SM-Rib galvalume steel 29-gauge roof/siding panels for the roof due to supply issues. The benefit with these was that the were pre-painted green (so I bought green roofing screws). Not counting site prep time it took me about 12 hours and cost approximately $600. This thing will outlive me, so "buy once, cry once" re the price. I learned so much about clever use of clamps from the video that I will apply to future projects. Many thanks for the great vid and plans.
For those counting, the shed holds 3 face cords, which is 1 full cord. Face cord = 16"x4'x8'.
Thank you for sharing!!!
and u saved money by using 2 by 4 for the roof??
That's the greatest selection of pressure treated wood I've ever seen! Great use of clamps too! I always forget to use them as extra "hands". Nice job
Quality craftsmanship. And a master lesson on how to use clamps. Killer work.
Thank you for this! We built one based off your plans and your video and just filled it up with wood!
That’s awesome! It should last many years.
Best looking fire shed I’ve seen 👌🏻
Like the gnome made squaring up blocks.Nice job.
Something else to note is that the run off is going to pool at the back of the shed, after running down the fence. Might not be an issue, but it does have the potential to create a problem. A simple piece of guttering and a rain barrel will fix that. Great job.
One of the many projects I need to get done this year. I'm going to build one like this. Thank you for the video.
Just about to build one next week. I appreciate this video and have learned lots. Thank you.
Built a similar shed with the help of your video!! Thank you
Excellent project!
OUTSTANDING build! I made one of these last year and man, I could have saved some time with some of the techniques you used. Your tip on airflow is spot on. I kept the sides like yours. I also kept space between the floorboards. We get rabbits where I am and I didn’t want to have a fully closed floor…so far no rabbits. Something else I did was get a tarp from HD and I put that over the front of the shed. I got screw in hooks and put them on the upper face frame to line up with the tarp grommets. At the bottom of the tarp I just zip tied a piece of pvc pipe cut to length. When it’s going to rain or snow I just keep the tarp down. It protects the wood nicely. Otherwise it’s rolled up to the top. These sheds are great diy projects
My friend, I'm having trouble picturing the way you stow the tarp and deploy it, if you'd be so kind as to make a video and let me know when it's uploaded, I'd greatly appreciate it. I love the idea of a tarp keeping things dry and tidy. Thanks
It’s a great idea…. I was thinking the same for wet/winter… im from NS Canada……pretty sure he was thinking tack tarp from the top plate on front and have laid downwards….attach the pvc to the bottom of tarp…. Roll up and secure hooks (or something) for when the weather is good…. Roll down when it’s crappy out!!!!
Exactly what i was looking for.
Love this great job.
Omg you made this so simple I am needing to build an "Going" to thank you!! I hit the button and bell!!
Amazing and yet simple build :)
Brilliant!
Nice work. I need something like this!
Looks great
Looks good!
Great stuff!
Great video. Thank you
You are right about the airflow. For that reason and others the flooring boards should have been spaced apart 1-4" and the entire structure should have been raised up on concrete piers. Wood with its' feet wet a lot will quickly rot away even if it is treated.
Спасибо. Очень поучительно
Lots of good techniques shown here! The squaring jig, using clamp for support, block spacing, etc. Hope you don't have any frost heave! Here things doesn't stay level for long
Nice work.
Thank you very useful video
Nice ! Great bro! ..well explained!!
Looks great and you just gave me an idea how to build my chicken coop. Cheers
Amazing!!!
Looks good
Good job amazing
Great video!
Nice job 👍
Nice work ,I made a similar wood shed from free treated 5\4 deck boards I salvaged for my floor structure . I used 4 by 4 posts for corners of shed and 2 by 4 supports ,roofing is same as yours .I built it all from 8 ft lengths to keep costs down .So the shed is just under 8 by 8 with a big overhang awning on the front made from rough sawn elm I cut on my property .I get about just under 3 cords wood in it loaded to max . The awnng on the front keeps rain off front of wood pile ,I no longer need tarp curtain on front .
You need also leave a space between your wooden floor and the ground to prevent rotten damage. Best way to do that is build your sheds on concrete blocks
Wish I had some of those wooden corner squares. That was a hassle trying to set them w the metal L square. My 1st attempt at a shed build and had to go back and make adjustments. Now I'm at this bracing the top part of my build, so I'm trying to measure and plan this part. * I do know some of my corners at the bottom have a little play so I just didn't crank down on the screws to try and be able to brace the top.
Good job
Nice job
Awesome
I would have left spaces between the floor for better air flow
Very good
Nice design and build. Next project, power wash the fence. 😊
That little shed is built to last 100 years!
Nice one. Not really a “mistake” but having piled wood in many different sheds I have come to appreciate some head room to avoid stooping. Realize you were looking for a spot to accommodate one cord. Nice simple build though. Great job.
I use some of your techniques For building a woodshed.
It's 8ft by 8ft With a divider in the middle. So, I can have greenwood on 1 side and seasoned wood on the other. My son is a co compliant officer here in my city. Firewood sheds have to be 18" off the ground because of termites. Termites have been a big problem in the past year. I didn't Want him to show me his badge and gun. It turned out nice. I stayed to the code.
I dug 4 Post holes in the ground 10" wide by 30" deep. And poured with concrete. With an 8" center block on top. We did 2x10 Floor Jionts, 24" oc, 2x4 Decking.
I like the way you did your 2×4 corners. And screwed them to the deck. You don't have to nudge your floor. Those corners always seem to break. And it makes it look nicer.
With 2×4 structure, you can fasten your walls up easier. I like using the five quarter boards for the walls.
The metal roof turned out Nice. because You help me not to make the same mistakes.
Thank you for showing me your biuld to help me with my build.😊
My next job is to build a wood fired pizza oven.
Nice
Muy buno el video 😎
Very good video - the techniques you used for 1-man assembly are helpful.
I’m sure your site put constraints on the wood shed. That said, I would make it longer and shallower so that you have only 2 rows of logs. Better airflow that way. Also, you don’t end up with wood way in the back that you have to move so you can burn it first next year.
The only change I would make, is leaving space for air flow in the floor. I will be building one soon.
Looks great. You may want to remove some of those decking boards around the shed. While you need some to keep wood in, you also don't want to restrict air flow. Some of those will line up with cracks between logs and restrict air flow. On my wood shed (which may be a bit shorter than yours) I only have three decking boards from the bottom with sufficient spacing and that's enough to hold it all in safety. Cheers.
I thought the same thing. The deck will get wet and probably start to rot
@@fireboltaz that's a good point too, but I meant decking boards he used to hold wood in...that go up to ceiling. way too many IMO
No, it will be fine. You can ignore this guy.
Great tip, thank you!
Wood sheds (up north) are usually built to allow more air flow to season the wood in 3 to 6 months. Never beside a fence that restricts air flow and never with a solid floor.
Put a piece of edge flashing under the short side of the roof let it go down on the facia board. good job built a few very similar. rough wood roll asphalt, can't get metal.
Does the flash edging go over the tin roof or under?
If it leaks or u use used metal remember the sealer used on mobile homes roofs. I even used it on OSB before
Nice little project 👍 I’m thinking this could easily be adapted for other uses - my future chicken coop for example 😁
Nice job. I like the use of 2x4’s for the corners vs 4x4’s (my last wood shed build). I would have skipped replacing the deck screws with structural ones- seems like overkill for something thats carrying so little weight…. I also learned in the comments to screw peaks not valleys in corregated metal? Huh- would have never guessed that.
Yea this metal was too flimsy to do that.
Can't you build a rectangular frame on the floor. Then slip it over the outside of the 4 posts as the roof? Then angle it and screw it. Wouldn't this be easier?
great video , so the screws for the corugated roof sheets should be put on the ridge
of the sheets and not the valley
Usually yes but, this Home Depot garbage. Manufacturer specs say to place screws in the valley because it is a thin gauge and too flexible.
I had to solve this problem in Germany last year. My project is very similar to Artisan's shed but smaller with somewhat flimsy roofing. It is under a pine tree that drops needles which would dam up in the valleys and flood around any screws in the valleys. So I went to Hornbach (like Home Depot, same orange colour!). They summoned the expert. He said "yes you screw through the ridges" so I asked about any support underneath and he took me to a dark and dusty part of the shop where there were just 2 bags of clear hard plastic bushings with predrilled holes that were shaped to fit under the ridge. I used relatively long screws with a special plastic cap on top of each screw. For screwing I like to get about 2.5cm (1 inch) of bite into the wood without too much downward force on the bushings/spacers. I torqued the screws to "snug" not tight. This solution was not obvious at the store because these accessories were far away from the main roofing supply area and only 1 guy seemed to know about it.
Good build. But if cost is an issue then one doesn't need such a well made floor. I also fit a heavy plastic sheet to the front wthat is weighted at the bottom for when the rain is tipping it down for a spell.
How tall is this structure? Do you think the dimensions of this could fit a charcoal and gas grill? Trying to make a bit of a bbq shed/platform and this looks like a good multiuse of it. Thanks!
Good tip for you... I see your screwdriver tip keeps coming out.. Use a craftsman one because it has a retaining ring to keep bit in place.. I don't use DeWalt anymore due to this problem..
But still good 👍
Never use roofing tar on a galvanized roof. Using acrylic Apoxsee our silicone. Tar will allow rust and leakage due to it cracking and breaking overtime from the elements.
i on this job right now without nice lumber ripping some pallets some old ply and whatever the bugs have left me of the 2by my ace the hole can of good stain
Framing nail gun comes in handy
It sure does.
I just built your mini wood shed. I am still learning and new to all of this. Your instructions were easy to read and made a big difference in the final product. After watching this video I am going to invest in some clamps! Also, do you ever use liquid nails on these type of builds?
I rarely use liquid nails or any construction adhesive for that matter. It is a pain in the neck to work with because once it’s dry you really can’t make any changes. It’s a permanent bond.
2 questions. 1. I thought the decking screws were self tapping but I see you drilling holes. Were there some instances where drilling was necessary or did you do that for all of them?
2. What's the purpose of the structural screws you replaced at the end? Are they that different from the decking screws?
I only drilled holes at the ends of the boards to avoid splintering. Structural screws are much much stronger.
Mine took more than a day but it turned out good
What kind of lumber did you use? Cedar?
Do you have a build of the wood bbq covering (pavilion) you showed at the very beginning? Thanks
Here you go. How To Frame A Roof For An Outdoor Kitchen / Outdoor Kitchen Build Part 11 / Post and Beam Roof
Doing this very soon...couple of ?s: Why not paint it to match building next to it. Seems like paint would extend it's life. Did you think of anchoring to the ground somehow? We get Santa Ana winds every year, so that would turn into a sail here.
Great video…I may try and build this and will purchase your plans for it if I do…but I just wanted to know, what is the distance from the lowest point of the roof “overhang” (behind the shed) and the ground? Thanks
I don’t remember but I there are pictures with measurements in the Etsy listing. Off the top of my head, I’d say 5 feet
Looks great man! I’m looking to build one of these sheds over the next few weeks. My only question is, should the floor be spaced out as well for ventilation? I honestly have no idea just curious.
A lot of people say yes, but I just see it as a way to make it easier for small rodents to get comfortable.
❤
I just priced this out in 2023 using the plans, and the consumables cost $639 pretax.
Could put a gutter and a little water tank off the side
Great video I bought your plans also very well done. In your plans you call for 14 pieces of 5/4 x 6 x 8. What exactly are those used for?
Thank you! Those are the horizontal pieces that prevent the wood from falling out.
This may seem a stupid question, but how do you figure out the angle of your cuts for the roof boards going front to rear?
Not stupid at all. The answer is trigonometry, but I suck at trigonometry so I use programs like sketchup and fusion 360 that do all of the calculations for you.
I would probably clamp the first roof support up there, then draw a plumb line down using a spirit level then match that line with my mitre saw. Not very high tech or mathematical but would work.
What about some foundation? Don't you think the wind could possibly move it/flip it when it's empty? I will be making a slimmer and wider one myself and I'm considering foundation options so I just wonder. Thanks
If you make it narrower you should anchor it. This one is deep enough to not worry about that unless you have to deal major hurricanes all the time. Also foundation is overkill. It’s only for firewood. Just make sure you level off the space where it will live. Lay on top of gravel or elevate on blocks and you are ready to go.
I got your plans for this thank you! Do you have any for a out house for cabins/camp?
Thank you! Sorry no plans for those at the moment.
Nice simple build 👍 I've planned something similar myself and am just wondering if your structure is rigid enough without any cross-braces? My plan is for a shed about double the size of yours and I live in a climate where I can get upwards of 50cm of snow on the roof so I've maybe overdone it with cross-braces in all directions but am wondering if its just unnecessary over-engineering...
I always think it is always better to over do it, than under do it.
Nowadays I'm building a 14m2 shed at home! 3m tall! Similar than yours, but bigger!
That's a Monster!!!
@Artisan Made what is the height diff in front and rear 4x4 to get pitch of roof?
I don’t remember. I built it a year ago. I think the pitch was 15 degrees
hi .. you're using 2x6 for the box at base right? I was thinking of using 4x4 on the box and 2x4 cross beams, but seems like 2x6 is easier to work with?
Yes I used 2x6. Less likely to bow with all that weight
Very cool but i think you need to use a better bit for the screws!!!! :)
What r the wood "squares" called? U used them to square up the initial floor framing... did u buy them? if so where?
Thx
I made them out of scrap. That was one of my first videos on RUclips. Check my channel page.
Could you put it on pier blocks instead of gravel to level the floor?
Sure.
Cup is wrong on some boards but solid easy build. Fence could do with a wash lol
Nice build. 2 by 6 for the roof is a bit overkill no?
2x4s will sag over time especially with the weight of snow on top.
I'm currently having to replace the tin on a 20ft.X 40ft. building because the contractor I hired made the same mistake, now the roof leaks ruining the wood beneath it "/
Hi there ! I'm in France and you're storage seems awesome ! Before I buy the plans, is it in meters or foot for the sizes ? :)
It’s imperial (feet)
Thank you for the answer :) @@ArtisanMade
I'm a newbie so excuse me if this is silly, but if I wanted to place this structure on concrete deck blocks to keel it off the ground, would that change anything in your plans?
I would say its ok. Support the middle as well though in the centre of the floor to stop any sagging. I try to raise my structures a decent height from the ground so I can see any critters trying to make it their home & it also keeps things drier.
I’ve built sheds on blocks like that. Add supports in the center as well. There is going be a lot of weight in there
How did you not get a locking T25 bit after it coming out out 15 times during the base assembly?!?! haha. Fantastic job
I have plenty of them now lol.
Small tip, you want gaps in the floor boards, partly for the critters you mentioned, but also airflow and the ability to shed water.
Great build tho, I'll make similar as my undercover areas are already taken up, and we are trying to transition away completely from our electric furnace
Also you're extra hole would have been less impactful had you affixed roof screws on the peaks of the ridges instead of the valleys, it's 'best practice' to avoid water penetration
Thank you, I tried installing screws on the peaks first even though manufacturer says not to and it didn't go well. These sheets were from my big box store and probably much thinner gauge than the quality ones. I should have used aluminum foil.
@@ArtisanMade awww man, I too have had this issue, they usually have a stretcher that's cut with matching waves to affix too. Either way, as you said some roofing putty will seal em right up
@@ArtisanMade I had better luck centerpunching and predrilled the corrugated
My first thought was “why not have gaps in the floorboards too”
Those green treated boards will shrink. We installed decks all the time with boards tight as can be. Several months later they had shrunk to a uniform gap between.
looks like you cut your horizontals slats about 2-3 inches short on the front, left and right inside posts...or was this by design?..lol ( my standard answer)
Those boards were 8 ft long cut exactly in half. Wasn’t worth the extra expense to buy longer boards