Видео

@@landonhardt7180 Original miles? That's insane. You will most likely need to blend into the hood and door. Panel matching is very difficult

Check out some of my other videos with ditch lights installs on both the the Tacoma and 4Runner and the Rock light install video and it might help. I don't know what wires are in that specific harness, but you will be cutting out the supplied switch and relay and wire directly into the Control Box. You will probably be using 2 circuits

@@zakmey6944 I appreciate it

@@joe41985 I agree but the Arizona summer is brutal and I had to stay out of the sun

@@nazimzafri If you go to 8:11 in the video I show the compressor and it has all the specs on it

@@AZOverland2017 thanks!

Does it

@@syncererush871 No, if done correctly. Check my other videos, I did one on this specifically

@@AZOverland2017 where is the other video???

@@syncererush871 Here you go ruclips.net/video/5QWPJvWGTk4/видео.htmlsi=f3DzihBWZbMa3HuC I also did a 1 year update.I am coming up on 3 years and have been through many car washes. It does not wash off

@@chris01479 Thanks! I like the way you think👍

I was actually looking at that one. Thanks for your feedback

🙏🙏

Yeah, I addressed that is the full length video

Thanks!

I don't have the app version. But, I suspect if you fuse tap into a "constant on" fuse, that would probably work.

These are not. Not ideal but I did just get one that is for the next project

It was included with the rack

There's only 1 out here by me in Phoenix that I'm aware of. I'm building a roll-up booth in my garage now...

@@thedengr My neighbor's are always working on some sort of projects themselves, so they are very cool. I don't normally paint in my garage. When I did this it was a weekday so there weren't many people around. I am in the process of putting together a very cool roll-up paint booth now with full filtering. I'll get a video out soon of that setup

Compressor regulator set to right around 150. Gun was about 22 for basecoat with fan wide open. If I used this for clear I would bump that pressure up probably closer to 26 and fan wide open. Fluid volume was about 3 out from close but I would probably open that a bit more also

@@AZOverland2017 thank you!! I'm assuming you used a 1.3 tip?

@@itsjusti4262 Yes

WE! Thank you, I appreciate it. Let me know if you have any questions along the way

@@justanotherday1345 Yes, you should be able to customize your gauge locations.

No KDSS

Thank you. The channel is gaining stream. Lot's of good stuff coming over the next few months...

I appreciate you sir 🙏

It's not necessary if you have the right cartridges but it would be nice to have.

What makes you say this?

@@szyang03 The fuse amperage you tap into is not important. They are supplying consistent power on 1 side of the fuse. The fuse is what protects the accessory. So, the 5 amp fuse will continue to protect what it was intended to. And, the fuse that is included in the fuse tap is rated to protect the Control Box power up. They are independent of each other

@@AZOverland2017 ah gotcha! Thank you for clarifying. New to this, so these videos are extremely helpful!

Yes sir, exactly! I neglected to put that important step in the video but I did PIN it in the comment section to clarify. Thank you!

@@upbuild4397 Thanks! The one I'm using is from 3M. I can't find the same one either but this one appears similar amzn.to/3S0S2HQ

Ah that’s great, thank you for the link 👍👍

@@jeffkeenan5439 Yes, definitely cheaper for a single stage and it was definitely a consideration. I wanted to keep with what the factory did. There were a few other reasons, but that was the main one

@@AZOverland2017 just find without a booth having to put down numerous coat with the clear over base method is your trapping a lot more dust bugs ect between the numerous coats

@@jeffkeenan5439 "Stuff" getting in a basecoat is typically not an issue. The basecoats don't go down very wet like clear. They dry fast and I'm using a tack rag between coats. Any imperfections can easily be sanded out and blended in before clear. You actually have more of a chance to bury dust and bugs in a single stage because you are laying down 3-5 wet coats and are usually not using a tack rag between those coats. The more wet coats, the more opportunity for things to land in the paint.

@@clr47524 Yes, we both still connect (Android Auto and Carplay) without issue. I still have it and it still works great. I'm very happy with it

I don't remember the positions. Do you have the shocks already? If you have them, they should have a chart of where to install the clips for each side according to the lift you want. If you are ordering them through Underdog Motorsports, Brett will preassemble them or tell you where to install them according to the information you give him

@@justanotherday1345 Exactly why I got it. I want to monitor temps before and after I install the trans cooler also

My brother drove it cross country through 2 days straight of rain and said there was a little water that got in but it wasn't significant. He had all his personal belongings in the bed

@@cherif731 👍

@@paulkeplinger3565 👍

If you prep and apply it correctly and keep the pressure washer at the correct distance and the wand is kept moving, then there will not be an issue. I have pressure washed my vehicle plenty of times without issue

@@clarencemack4382 There are a lot of variables to consider. What kind of gun? Does your compressor have a quick recovery? What pressure do you spray at? With my particular setup, I was able to spray the entire car. The compressor kept up. Your going to need to get used to what you have and how to adjust pressures as you need to. If the compressor is good, then it's likely it will work

@@JR-pd9xz Check out some of my other videos after this one. I did an actual install of this unit on my 4Runner and I did a fuse tap video. I also did a few videos installing another switch panel (Mictuning) on a Tacoma

Thanks for your feedback! Yes, I think too many people get carried away with disconnecting stuff that may not be necessary. Good luck with the new setup

I've used 4, but have more additions. Ditch lights, lower light bar, and 2 color rock lights which take up 2 buttons ( 1 to control white and 1 for amber). I'm adding a roof rack light bar with potentially 2 modes as well, and rear tack lights. They can be used to control a horn ( if you get one with a monetary function). They also have them in a 4 or 6 switch configuration

Got it!👌

I followed my instructions that said concave facing up. The picture on the manual also showed it facing up. I have not contacted Bilstein. No issues or sounds for me either

@@AZOverland2017 Ya. Completely random post on a forum led me to look up pics of 5160 installs to try and help them and found an install from 88 Rotors (big installer in Southern California) with the washer the other way. Piqued my interest so I googled "Bilstein 5160 Install Instructions" and found a Bilsten official link with a PDF which showed the washer the other way. And, of course, I have my 6112 instructions, but can't find my 5160 instructions. Not worried about it; it's more of a curiosity at this point.

Thank you! I should have a video out this month on a great, portable, and reasonably priced DIY paint booth. It will deploy in 5 minutes and be extremely effective Thanks for watching

Thank you 🙏

Lol