Видео

Nice work bro keep it up

I love your videos!

Can i diagnose a GLoD ps3 so i can harvest its gpu?

Loving the videos. Can you make an equipment list so I can shopping and have a go whilst keeping the costs down!?

Love that spudger you have for IHS. Could you please share a link on where to get one?

Must be a new Trend word like "Hangry". "Haversting".....

No way hes back! How is the new apartment?

Is a 40mm rsx frankie compatible with ps3 model cechg03

AMTECH NC-559-V2??? For 30-40 USD you can buy Warton Future HF Rework Jelly Flux 30g. Please consider saving up money for a Warton.

I have the PS3 fat with a bad BD can I install CFW noBD as an upgrade

Haversting 😂

Im gonna be the first one to witness a frankie with 65nm rsx

i ordered three things from alliexpress i got one and enver the other two. i always have issues with ordering stuff from them

The LCSC cap in the first picture appears to have a damaged case.

Cool video, thansk for sharing

ช่างไทยเจอแดงไปเป่าcpuอย่างเดียวไม่ใศึกษาให้เยอะเหมือนฝรั่ง

Essentially the YLOD is similar to the check engine light on your car.

what a great content to be shared

you also using very bad flux you need a fluxplus and solder with a high tin content

3:00 you can easy clean all glue with clean gasoline like for zippo light crackers and etc im usually buy high octane gasoline that is specifically sold for cleaning electronics. it is sold in electronic component stores. this is also the same gasoline that is used in motors for radio-controlled airplanes

isn’t the 65 nm rsx reliable?

Tantulum is bad idea really bad.After 10 to 15 years they go bad and tend to blow up when power up.Rather order the same nec tokin from jp companies

This worked perfectly, thanks again. For any haters.... follow the process....it will work😁

Although I do buy stuff from Aliexpress the first thing I do is replace all the caps, if it's electronics. AQnd as you were opening the parts i knew the first bag was Aliexpress just buy the inferior look they had. I prefer Mouser just because the interface is better.

Great video by the way!

Hey, I bought a Super Slim for 30 bucks and I was using it for loke a month playing demanding games like GTA V and The Last of Us, temps didn't went over 70°C but a week ago it started showing small artifacts, it was never opened and it have a lot of dust inside (i dont have the tools to open the thing) and I want to make sure if the RSX is dying before wasting more money in it, any recommendations?

Its not a failure, its not your fault that the trace came off, mostly importantly it can be repaired even if the whole trace came off, you just need to look for the right spot on Xdr ram and then make a trace to connect it to Cell.

Definitely check into some low melting point solder. Makes much quicker work of them without risk of damaging traces or other components on board

Its pretty strange how most issues I see people having are with the midnight blue ps2. I have one, but its laser died. I was gonna replace it, but i opened it up and found it was the "impossible to find" PVR-702W laser. I had to get a new ps2. I really wonder if the midnight blue just had a major manufacturing issue?

Not for me, very low quality, I blocked Aliepress ads, last high speed ssd I bougth from ali claiming pci 4 was slower than a carrier pigeon and burnt up severals days later.

According to your measurements DigiKey is the only manufacturer delivering all capacitors within spec, since the capacitance of all LCSC capacitors and some of the capacitors from Mouser appear out of spec (20%, so max allowed capacitance is 564 µF). It's hard to say if your measurement method is not causing some shift in the data. A standard multimeter (even a fluke) is not the best instrument to accurately measure capacitance. Assuming that the capacity measurement of your multimeter is higher than the actual value (which it likely is), DigiKey and Mouser are probably in spec while both LCSC and AliExpress delivered all capacitors out of spec. In order to accurately determine if the ESR is in spec for the capacitors that are measuring close to the manufacturers maximum value, you'd need an ESR meter capable of measuring at least 0.1 mΩ. Preferably an ESR meter that can measure down into the range of 0.01 mΩ at an accuracy of ±0.1mΩ on that range should be used.

5:00 😂

Ali express lol Looks horrible 😂

it is not normal or at least professional to pack parts in kitchen wrap especially statically sensitive parts like semiconductor parts.

You buy chinesium you get chinesium

It's video, not wideo.

I avoid Aliexpress. TEMU is OK, though, right?

Thank you for this video! It saved my CECHC03 and my G04. Small correction I'd like to add: All PS3 lasers have 3 lasers inside. One blue, one red (dvd), and one ir (cd). You couldn't really read different media it without the different specific wavelenghts. Don't get me wrong, I'm not arguing that the newer drives can be more relaible. I juts have no info on that :D

10:36 I also tried to remove the defective capacitors. In doing so, I destroyed the components on top and lost them. I'm probably too clumsy to solder.

Thirteenth is with a TH (13th), only a single three alone uses RD the (3rd)

LCSC is a Chinese supplier with a pretty good industry reputation for both quality & good prices. Digikey & Mouser are both very good quality, but boy, you sure pay for the fast delivery!

The "sponsored by my wallet" bit got you an instant upvote from me. lol

*MOST* useful review of the entire yt !

1:14 Where’s my capacitors ?! 🤷🏻🤷🏻‍♂️

When I was in high school in the 1970s, a long time ago, I worked at a repair shop. If I would open a unit and see tantalum capacitors, I would not not do any trouble shooting, but would just replace them. Worked 90% of the time. Have they gotten better?

No cam ?