Видео

thanks so much from Melbourne ... about to replace our skirting and your tips will be applied. Good one Rick.

did you say cabinet grade? 🤣🤣 please I can't stop laughing. Perhaps I should put a Porsche sticker on my Toyota that will make it go faster!!

Thanks bro

followed your instructions and made one for my table saw which is very similar to yours. very happy with the results. thanks very much.

its nice. but the accessoires asre at the same price as the saw itself... cringe.. for this cash + the cost of the saw, you will get a better tablesaw by itself...

what a load of c r a p

cope? coping? you mean scribe joint

Brilliant, I don't want to be a nag, but I wish you wore safety glasses when making the cuts

I have been fitting Amtico flooring for 26 years and you never cut the door off square. We mark the door and remove it then we use a router to cut a rebate on the door so it fits over the door bar but stays long on the room side to avoid draughts under the door I'm sorry but very amateurish video.

Why don’t you build a good Fence. Not subbed

Loved your video. I have the Dewalt 7491 and the BOW fence. Didn't know the Jessem Guides were an option until I saw this. I ordered them today and am preparing the same set-up. I couldn't tell if you milled down the thickness of the 2x4 you used to mount this. I know you took off some width, but did you decrease the thickness at all - or just left it at 1.5 inch thickness. Thanks again for the video. I'm looking forward to this set-up.

What a palaver, any decent carpenter would remove the door (without damaging the hinge rebates) and cut the door to size. In my case, more often than not with a hand saw

👎🏼what a faff

This is an outstanding modification. I currently have the DWE7485 model. Is that the one you have or is it the 10" model?

The prices are a little steep for an extruded aluminium fence. The markup on this must be huge. Only a matter of time before China Tools (hooked on wood.....) undercuts this.

And how many doors would you expect to treat to justify the cost of such a specialist tool?

Tipicle diy idiot,we get loads of knobs like him in the trade,on price work he would make about £50 a day.but they expect £220 on a day rate absolute clown 🤡

I must amend my Christmas list!

Old school here, definitely should have 3 hinges, take the door off scribe a Stanley blade on the top side as circular saws cut up causing chips on end grain and painted surfaces even when using a triple chip blade. After cutting very light sand on the edges. Rehang the door, it’s a ball ache but that’s what I always did. Proper Job🤣

How about taking the arris off the sharp corners ?????

Festool clamp and rail “SO”…1st.. a mortgage needed, then get a 2nd top up motgage for the Festool Track Saw and Vacuum for dust extraction. Then spend time clearing things out of the way to open the door wide enough, that’s if you can !! Then pray that you set the saw depth right so you don’t cut into the wall, architrave, skirting, or damage the carpet….. 😂😂😂 I’d Just take the Door Off‼️

Using tools everyone has in their house!

What is on top off the bow xt fence?

Inspired me to comment..I don't usually. I agree with a lot of the comments re door off easier in general. However..thank you for the video as I hadn't really considered this possibility before. One day you never know might be a useful tip to deal with trimming a door/woodworking problem.

No need for all that, door trimmers are available from tool hire depots, in fact I've got three different makes and can trim door in situ in about five minutes,

Primer? Don’t same in between coats?

I watched this video, and live in a tent ! Well done though. 👍

Doors off for me.

I would takedoor off after markinghow muchto remove 15 mins top

It’s not a door bar, in fact , that’s not even a term for anything!!! You’ve just made it up. It’s a THRESHOLD strip! Learn your terminology.

Nearly cut through the skirting board too. Those saws and slides are about £500!

Hi, did you have to pay import duty on these tools? Were these tools not available from UK suppliers? many thanks.

I would bevel the door so it doesn’t look so short on the lounge side .

Just another crummy gadget for those who are more interested in buying fancy expensive gear than actually doing the job.

If thats a heavy door where is the middle hinge.

Anyone else screaming - use a sacrificial wedge to hold the door in place?

Faff and sloooooowwwwwwww

If only we had time to do this on jobs 😢

£47 for a clamp!!!! I’ll just take the door off thanks. Couple of air wedges under it , then no damage to the hinge mortises 👍

I want one!

Great products. But I wonder if paying for all of them is not already the cost of a decent cabinet saw.

Line up the back of the skirting, mark your short and long points cut the skirting check how they fit and simply adjust withb a block plane jod done

Nobody likes caulk smear

Не знал о таком. Интересно характеристики этого соединения

There's a tool they sell at Home Depot that cost around $6 made by husky that has a silicone tip that will remove all excess caulk and it even has other functions like a old hard caulk remover or scraper. It even has three different sizes on the silicone tip. Tape gets really expensive especially that orange tape which is also aggressive on paint. Buy a tool once and use it many times or buy lots of tape, it's up to you. Have fun with your caulk guys ✌️

Box of clips £2 39s Milwaukee tool £200 15s Ill take the 39s every time

Using loose pin butt hinges makes taking the door off a doddle. No, I wouldn’t do this, I can see all sorts of trouble.

Thanks!

Smart person would CAULK BEFORE PAINT!!..

Or plane the back of the skirting like a carpenter would do