Видео

bluetak will pull anything and everything out of your motors and bells.. no brushing... no shower... easy peasy

Have you tried it on 6s with bi blades and 6 inch props on the bottom? Curious for compacts heavy lifting drone

I just got this frame too. Will run 1804 2450 kv 6s. And a 20x20 stack. Whats a good tune for this?

2000kv is fine for 6s on 3.5inch. I run 2450kv 6s on 4inch with 1804 motors

I had a GepRC naked GoPro 11 that would power on just fine, but one day randomly refused to start recording no matter what I tried. I was unable to reinstall gopro labs firmware because it was stuck in a reboot loop. Finally I installed the original gopro firmware manually and it worked, but then I landed where you were with official firmware. This tutorial is exactly what I needed, and worked perfectly. Cheers!

Ur running 6s on a 2000kv. That’s a super trust

can i install gopro labs to my an external battery work with out the go pro battery in the battery slot? Without taking it all apart???

love sound test. unfortunately, i want to see compare sound test between pico and pavo20 pro.

Thanks a lot man

Hey man, thanks for your video, I’ve got a GoPro 12 I’ve converted to naked. When I try install the GoPro labs it keep rebooting and flashing screen. Doesn’t ever show installing. I’ve tried working a 6s battery plugged in through the balance cable and also through plugging the old GoPro battery in

Change your bearings.

This issue hapen with me now ...

Detailed step by step vid! Thx a million. 😊

Can the dji fpv controller 2 be used with this?

Thanks Sifu, really helpful. Remind me my quad fell into the sawah padi totally covered in mud. I did unplug the lipo underwater; washed sprayed contact cleaner; dissembled and dried everything. All work and fly fine except VTX intermittent interruption .

Mantap bro salam kenal salam satu pilot 👍✌️

fun fact it's actually impossible to bring any battery down to zero volts as volts is just the difference in potential, and the chemicals will always have some potential between them.

Great video! Something else to be aware of, the contaminants left from water can cause corrosion to start but not cause issues right away and can kill a component randomly several months later even though it was working fine after the plung and drying, this is actually why you want to use the IPA to actually clean the electronics, removing camera housing and all that, don't just thoroughly dry everything, hope fir the best, then try flying it... It might seem fine, but could suddenly drop out of the sky 6 months later on someone hurting them... I had one that spent months in a tree before a storm finally knocked it out, everything worked fine for months, then it finally died mid flight, upon inspection corrosion slowly built up under the components, just took time for a problem to develop, washing down with IPA seems to help that, i also use vip camp dry occasionally on my electronics, the silicone coating helps replel any rain drops i might fly though and its easy to just give everything a spritz occasionally the night before flying

There is no point in destroying the battery if it wasn't overly discharged while underwater. They are a sealed which makes them pretty much waterproof.

Great information

very helpful. Just here to point out that in 5:04 it’s the small resistor to measure current.

fuck yeah dude

Have the same issue with go pro 6. Have installed 1.6 firmware but still face this issue. And as I can see there is not GoPro labs for hero 6. Don't know how to fix it...

Just build the GoPro 11 in the geprc case. Now nothing related to gyro seems to work :(. can't use hyper smooth. But also cannot get motion data for use in Gyroflow or real steady. Did you happen encounter this before?

Nice video mate. I’ve also been struggling with all the jitters from my cinelog25 whenever I add my naked gopro on it. I think that I am not being able to get my gravity center correctly, as battery can’t be pushed back to balance with the gopro. And I believe it affects my pid looping forcing my fc to be always making lil adjustments while Im flying. Causing then these micro bumps that I don’t have on other quads. But I can’t tell for sure 😢

you are such a life saver!!!!! thank you!

That pliers bending method, genius. Tape to remove metal shavings from magnets, genius! New motors are nice, but if i had to buy a new motor every time i flew into some concrete I'd go bankrupt.

Can I copy your PID Tune?😢

Well presented. Thanks for sharing

nice video i like the format

Wow I think I have learnt something from this video. Thanks.

Great sharing bro ...

Yep usefull :) thanks

Not advice that I care to follow, based on the fact that he fan dried his electronics, right after giving his drone an old fashioned shower in his bathtub! Can anyone say "rust",??

Good video dude

DO NOT brush motor coils with a metal brush! the wire has a layer of silicon(e) to prevent the wire from shorting out on itself!!

Ah another Klang boy. Which high school you went to?

Hi bro, my one is the first gen Tx16s. So i have to buy the ELRS module to bind with the pavo pico, right? do you have any recom for module? pls. is it should be fine BetaFPV ELRS Micro TX or (V2) Module 2.4GHz

thank you, very good explanation. is the o3 air unit compatible with the dji googles integra?

Great video! Should have 10x the views

So … I messed up. Exactly what you were worried about… I stripped my screw and now I am clueless as to how to open the bell as there is a piece of junk inside ta motor which I need to remove. Pls help

do you need separate screws for the motors to sit comfortably on its thick frame? im thinking of getting xilo stealth 2207 motors and i dont know if their screws are long enough. thanks

Is it possible to using speedybee f405 v4? Because in their description it's support 8 motor

Link on that cool plier..

Like your presentation, btw what was the total weight of the dslr including lens ?

0.16 was the best version? I think that’s what Ciotti was sayin’

Great content. Very useful. I'm subb'n ya bro!

Do you think that a AIO that uses mount holes of 30.5x30.5 would fit in this frame? I have a 3d print part for the conversion of 30.5 to 26 or 20 mounting holes. Aio itself measure 38x38

Good video. Thank you for he great info

Great Video - Thank You for sharing !