Видео

Thanks for the good info it helped alot!

One of the ends that plug into the motherboard is burnt, can it be replaced

I was about to throw out the whole thing lol thanks for this video you are a saint

awesome. My dealer doesn't have a full replacement. They say its the motor that was previously under warranty. So i'm replacing the motor and will clean up the unit as best as I can. 355,000 kms later.

How can I get that diagram?

thank you for posting this.

Thank you for the trouble of filming this. I am needing to move a toilet a tile-thick over. It's touching the wall without tile now, so it's just a little bit. I think the offset flange would do it just nicely.

Mine seems like a weak battery but when I release the key it turns over , mostly after I've been at interstate speeds or pulling a trailer but not always

Probably could have just replaced the voltage regulator, I think its external on the back of these alternators. My 92 isn’t charging so I gotta look into it tomorrow unfortunately.

Got a 94 f150. Is the part a DS268?

this might be the most useful video on the internet for me today.

Informative. Thanks.

What book is that? Where did you buy it

Why do you have to clip the wires? Why can't you just pull the original plug with the wires attached from the alternator?

great and simple video; no fluff. where can i buy the control board.

It's a good idea to put some building paper flashing over the patched hole, and slipped up under the shingles above. Then install the new shingles over the building paper. Keep water out.

My fiancé complaining is what got me here thanks bud 😂

Thanks mister u saved my bacon 😂

5 thousand nahh

Where did you purchase the cedar shingles?

I was losing my mind trying to reload this. Thank you so so much! What a poor design!

They don’t make them like this anymore. These were built to last. Talk about getting your money’s worth buying one of these back in the day!

Thank you!!!

My truck is stuck in park with a no crank no start. If i turn the key part way itll let me shift into neutral and then it'll start right up but it'll get stuck in park again. Any ideas? 99. f350. I think this is about the only part i havent replaced yet

you can't even see what you're doing cuz the camera is too close

I would have brought the toilet flange out to 12" from the wall,and made your offset in the basement. In Florida, our houses are on slabs so we don't have the luxury that you do. Nice work.

1:20...is all you need, NEXT vid

Thanks, I haven't started yet, but now I know how to start. I'm hoping it won't be the board, I could use a money break. So I'm expecting the board. ( nothing wrong with a little reverse psychology right? )

MVP

thank you👽

How do you adjust so you don't have to turn key so far

Thank you so much. turned out to be easier than I though haha 😅

How do you remove the loaded tape?

Thank youu!!

The trick with the larger socket was a life-saver for me today. Thank you!

You can disconnect the pipework by blowing down air down there... More over, you could be compacting the blockage making it harder to dislodge.

Thank You!

Wasting yor time on that tecumseh buy a predator engine saves a lot of time

I do a lot of these I usually just put a new predator engine ohv engine on them direct bolt up makes a nice tiller the engines run around 100 to 140 harbor freight.

They still make troybilt tiller horses mtd owns them now I think they bought them back in 2001 still made in Ohio I look on line around 3200 dollars now I love these tillers I done tons of these caddillac of tillers.❤

What is the name of the manual that you are referencing?

I have a 2007 Ford f150 when I turn the key it seems like it keeps wanting to keep turning over can you please tell me why it's doing this thank you very much

Nice job. I have a few cedar shingles that need to be replaced. This video gets me started in the right direction.

Ty soooo much !

I learn something everyday, thank you so much! I didn't know about the single wire that is plugged in on top of the starter solenoid, I got the feeling that my problem is the safety switch. Seems to be exactly the same symptoms.

What size were the wire connectors needed for the 3 wires?

Esta bien explicado pero no se ingles

Great videos.....no fluff, just good stuff. Thanks!

Thank you found a label maker in the trash tonight didn't know how to work it 👍🏻

I sure do love my 79's 😍 Thank you for the vid, weather stripping is always a pain