Видео

Can you tell me the distance I need to have between the magnets and the round indicator or round ring that it picks up off of I'm trying to assemble one on a trike and it's a lot different than on a regular bike

Can you hide the sensor somewhere else with a magnet attached to it, so as to trigger it Or this won’t work? Does it have to sense a magnet moving across strictly periodically?

Super confused why people are saying not to touch it. It just smells and tastes like rotten flesh. It's edible and safe to handle.

I can just disconnect the sensor wire plug from the controller wire plug and it just goes off of throttle like pedal assist isn’t even there. I have a rear hub 2kw motor. Seems to have more power and speed because pedal assist doesn’t work at 35 mph anyways.

You sound just like Elon musk….

Good evening . And how many BETTER magnets should this sensor have!? I have an older model bike; / There is NO on-board computer, only a small board with LEDs. and its natural PAS sensor consists of only 5 magnets!!! / Today there are 8 of them and there are also 12 magnets. So is it possible to replace 5 magnets with 8? What will change!? Will there be problems later on the road!? Thank you .

Hi, can I disconnect the pedal assist all together? I don't even want it on my bike anymore: it doesn't work half the time! Thanks for your help😊

When you stop on a hill you won't be able to move, but it does invoke some ideas, thanks 😊

What if you simply remove some of the magnets on the drive disc sensor so it thinks your cranks are spinning slower than they are?

Hall effect sensor

I bet this guy works for NASA now, This is a pre pandemic. Trust me A lot has changed in the e-bike word now.

hehehe i can see some poor guy trying this and the bike running away him,and he cant stop it. its really not had to add a twist throttle to any ebike ,can just get a pwm driver chip a few components a hobby pcb a throttle with a 5 or 10 k pot be easier ,than hall throttle ,tjhere is plenty of circuit diagrams online

If you have a “pedal assist” only bike, buy a cheap “5V pulse generator” (NE555 timer) and a momentary push button. Set the pulse generator output to around 25HZ (max for mine was 45). Remove the crank sensor (cut the wires, there are 3) install the push button on the 5V line (red) and wire the output of the pulse generator to the ‘signal return’ (blue) wire. Push the button to turn on the pulse generator, and it will send the pulse to the controller and the back wheel will turn. Let go of button and it stops. Pedal assist only to throttle controlled ebike. Get fancy and instead of push button, wire use potentiometer control that twists like a throttle, with a 3D printed mount.

Nice hands huh

So if you disconnect that wire it will go faster correct the sensor wire from the controller

The whole point of a pedal assist sensor is to power the motor WHEN you pedal. If you don't want to pedal, then use the thumb throttle instead. If your e-bike doesn't have a thumb throttle (or a cruise function like my ebikeling kit) then you purchased the wrong e-bike.

Tried worse way to do almost killed myself while turning slow motor kicked on

Most ebike kits have thumb throttle or twist throttle so this is not necessary.

I have psa and twist throttle so I can use my bike without peddling if I want to. There is no need for your idea of putting the magnet and sensor on a wheel to obtain motion without peddling, a twist throttle automatically disconnects the feed back from your peddles and sends power to your wheel regardless of what your peddles are doing.

Elon musk?

) was

Imagine , when you want to make very slow U turn . If you don't hold the brakes to kill the power you can be very surprised. Dangerous. It's call pedal assist. Best position is to be there. Not Rim assistant or wheel assistant. Magnets on the spokes are used for speed calculations. Not for this.

best part 7;37

In the UK you have to be pedalling to use PAS, otherwise your Bike has to be registered as an EAV.

I would gi e this video 10 thumbs down if I could supper unsafe should your brake sensor fail you become an angel real fast just instal a trottle in your bike or change the controller to add a trottle

Hello from Athens, Greece. May I ask a solution if it works better and more easy as I think I see it ? If in this disk with a lot of magnets you remove the half of them will it increase the final assisting speed? Thanks in advance.

That's one way to invalid your warranty on your expensive ebike

Please don't knowone try this!!! Trip to E R for sure

One problem with this setup is your going to constantly be running the motor any time the bike is moving which is going to shorten your range. You can’t coast downhill without using power. I had thought of using a push button connected to a small flash circuit board powering a small electromagnet to trick the sensor by flashing the electromagnet on & off but I came across a perplexing obstacle. If the sensor simply reads the magnets passing in front of it why doesn’t the motor turn on when I pedal backwards? Different strength magnets stepping up in power to provide a sense of direction to the circuitry? I think that’s a possibility but not sure yet. Haven’t tried testing that theory. Any thoughts?

Would it be possible to bypass the sensor? My sensor is broken and I'm thinking about tricking the sensor system so that I dont need a new sensor.

Crock of BS

You did actually show hot yo do it and if it works

Can you show how to increase the speed limit... Because I can use my cycle without pedel but it's limited to 25kmph

Not work

Hmmm If you don't like pedaling buy a motorbike if you want more speed shift the sensor to the frame and stick the other magnet on the pedal shaft so the two magnets pass each other when pedaling this will trick the controller to think it is going slower than it actually is no resoldering just a bit of glue and a couple of zip ties

boring

I am really excited at this idea. I want to keep the magnet disc in place exactly where it is and I have new magnets that I want to put on the spokes. Does anyone have any idea on how to do that? They are small single magnets and I want it to look clean. My thought process right now is to either get a wooden dowel and paint it black, cut it in half, glue the magnet to that and then put a screw through the two halfs of dowel and put the spoke in between to keep it in place but I hope theres an easier way. Like i say, i don't want to cut the magnet ring into pieces and I want to keep it in place for the future or just in case for whatever reason that this doesn't work with my bike

A terrible podcast.

Our saucers work like this

Kinda looks like crab meat, but seriously, don’t even try touching it.

A lot of pricks in the comments here 😂😂😂

Jesus ..I fell asleep twice !

So I put the magnets on the wheel that doesn't have the motor in it, I have the motor on my back wheel, so your saying that its goes on the front wheel ?

bro how do fix nordvpn when i double click it, it dosnt open at all and when i try to open it, it dont work

All thanks to your drakehack01 who help me hack my meter without delay on Instagram.......

*THAT WILL NOT WORK YOU FOOL*

Hello I have 1 TH X3... loose password. Do you have a sdcard image for recovery please ?

Pedal assist is good to have.

It belongs on the pedal, that's why its called pedal assist. If you want constant power install a throttle

brah how many times u wanna say uhhhhh