Видео

Enjoying the videos. Best of luck with the change to fill time. What aspect of engineering were you consulting in if you don't mind me asking.

That’s Rossmore headstock on the loader

Interesting video a little insight of what you used to do, we just had a couple of ridge tiles fall of the house so have be quite lucky.

I hope you will make it as full time farmer it will be hard core

Glad to see you didn't suffer too badly eg loss of livestock or machinery 🤔 our fence up the side of our drive got blown over fence is still intact but every 6 inch upright posts snapped at ground level 😡😡 congratulations on becoming a full time farmer 💪👌

Storm eowyn was really very rough storm here also in ireland some sheets of a round silage pit sheed also used for hay & straw bale's

Where abouts are you based?

Massey had loaders made by Steelfab of Cardiff.

No damage done to our farm apart from two slates of two different roofs, there is however no shortage of supply of firewood for the next few years ! You seemed to have got away light enough compared to some farms. Interesting video, keep them coming.

Lost a few sheets of tin of an old stone barn but like yourself we have plenty of trees down still no electricity shame about your shed

I rekon the slate roof is at the end of its life and the nails coroded. May be time to ree roof with tin.

Thank u for ur video

Great video can wait for future episodes

You got away not too badly from the storm. You’ll have plenty of firewood from the fallen trees anyway. 👌

watched, subscribed a while ago and liked. thanks for the update, luckily minimal storm damage

Is it spooners where you were? Ilkley?

Hure bag storm

U can see my house 👁️👄👁️

Euro 3 bracket

Sounds good

I think I have 1 off those on a old loader

Are you sure it’s not brake master cylinder?

those look like quickie 3 brackets

I think I’ve a head stock in work here that lookes similar to yours if you can get in tough with measurements and that, can see if it would do the job

I've got a 810 loader its the same as your loader.its a faucheaux attachment.ive converted to euro so I've got a complete Massey 810/815 headstock available??

Good to hear you're making progress round the farm 👍 got no experience with massey loaders or Matbros so sorry cant helo there 😕

I think it’s an alder quickie head stock pre the euro head stock.

I think your rev counter runs off your alternator

That headstock might be the same as what rossmore used. The older quicke ones had a smaller top bar then what u have I'd say. Send me on measurements of what u have and I'll let you know

Id suggest trying Winston Loane Tyres( fermanagh)he carries a selection of 2nd hand stuff and would be one of the first places i would think off it might be worth a phone call

390 has whats called a SMS quick hitch, was a standard fitment on ALO/quicke/Trima, Sigma 4 and Hauer loaders in the 80s, 90s and early 2000s we even got here in Australia. Should be 1050mm between centres

Tanco headstock on 390

Could be the brake master cylinders that are leaking..if it's the orbital unit don't waste your time trying to repair it ..replacement is the only cure

Will try to help out here as much as i can. Matbro headstock looks like its from a Sanderson. The headstock on the Massey loader looks like its a Quicke of some sort, possibly a 3 but i cant say for sure from what i can see. Gribben tractors at Portadown deals in second hand tyres, massive selection so try him first, 12.4 in 24 inch could be hard enough to get but hes probably your best bet that i know of, he also deals in buckets, attachments and headstocks so talk to him. Investigate the orbital first and find where the oil is coming from, it may only be a slack pipe or a cracked fitting, an orbital has to be timed correctly when building it or it turns into an oil motor and the steering wheel starts to spin itself when you start the engine. The 390 rev counter as far as i know works of the alternator. Its possible to fit an alternator with no rev counter output on it, again check this out first, as far as i know the rev counter does not have a separate fuse, its also possible for the rev counter to fail but that's rare, its probably more to do with there is no signal getting to it. Definitely agree with you on the fresh chicken eggs, hard to bate.

As far as the case goes you could call tractorpart in England they specialise in case and international stuff you can pick their brains on the subject

Quickie euro 3 brackets not euro 8

I would say probably an old style quicke loader quick attach. Massey loaders were made by Quickie at that time.

Your Matbro has a sanderson headstock

It looks like a euro headstock gribbens in Portadown are great for second hand tyresthey sell tractors and loaders too

The Rev counter runs of the alternator I think most likely a broken wire

It's an old style quicke, with quick attach

It’s the older type euro headstock

The eggs from your own hens are always good, i reckon eggs have different tastes depending on the area and climate aswell

Massey ferguson 815 loader is a quicke and the quick attach should be a quicke number 3. The alternator drives the rev counter and if its charging the counter should work, if its not working remove the dash cluster clean the main electrical plug

Think that’s the old Euro headstock

Tanco I'd say. Holes directly under one another.

I have zero answers lol. Gone sell me them fertilizer pallets please. And anyone reading this I will buy fertilizer pallets

Matbro headstock for sale in co Monaghan. He breaks a few bits and always has bits and pieces.

Are you sure it's steering? I would think the brake master cylinder is up there. Could be as simple as a rubber pipe perished or master cylinder leaking. Pretty sure the headstock is early euro bracket or quickie. Try Gribben in Portadown for both tyres and the headstock.

It's not a tanco headstock. Tanco brackets are way shorter but same design. That headstock is designed for that loader which is a steelfab loader.