Видео

What size garage is that?

How to join two laminate countertop

I do bathtub and tile refinishing , every time i resurface anything I mask off the surrounding area even my setup area I use drop cloths . Customers really appreciate it .

If it aint broke dont fix it

Ive been painting for 2.5 decades. I can cut crispy lines...I've started using tape & masking any time I can. The process doesn't make a true pro, the end product does. Nice job.

Theres paint on the carpet ..

Trash

This bag has held up really well for me.

Nice set up. I have that same bag and i love it

That’s where they used to do it back in the old west

Who ever installed that door is going to get sued!!! The door must swing out due to it being on a staircase

Thank you 🙏.

I have no idea what you’re talking about but I like the idea!!

Duh.

fucken genius!!!

lol bro everyone knows this

Lets see the straight one cut please

Very true! One cut.

Measuring is hard... 😢

One of the reasons for the rot comes from the concrete pad at the door being too high, which allows water to splash up underneath. Sticky window/door flashing tape about 5 inches wide should be run around the door opening first. Then metal flashing applied so it sticks out onto the concrete under the door threshold. Then another layer of sticky flashing tape over the metal flashing at the door frame. Caulking also where you've shown at the bottom of the door. You might also want to check the downpipe and gutters to make sure they are clear. Would be a good idea if possible to route the downpipe away from being next to the doorway.

I thought that’s what you were supposed to do. What do other people do?

The warranty calls for 3 screws but what I do because fascia screw are ass is I like to pre drill but took a combination square drilled holes in it so everytime I pre drill it's in the same holes everytime

How far apart are deck-joist put for composite decking? I'm 2' on center with R-CUT 2x6s......

Where do you buy the plugs at?

I have a 2800 psi Ryobi 2.3 and it is leaking oil from the carburetor when it is on, what could it be?

thx that's so much easier to carry to my truck! 🤭 🤡😋

thnx dear ❤❤

When I use ledger locks for posts I’ll just pop a nail on the post n it holds just fine and saves a lot of time

I work alone too . I can never have enough clamps

Plumb your post

Quick tip. Dont attach to the house

The post needs to be in the ground

Or you can build roght and have your podt go straight to ground sitting on sona tubes

You know bro, there’s reason only few people like it in 3yrs. Talk less and show more… in fast forward style these days to make money here!😂😂😂

Milwaukee 15" structured tote best bag I've found

What a great communicator. Nobody knows what you are talking about. I think he is taking about start boards on the same side for boards on top and bottom of the video screen. Isn't that common sense, Einstein?

Will this run a tornador?

Gonna get it.

Correct.. the perfect way

I personally use a chainsaw. Get a sacrificial blade in case you hit any metal.

I’ve got a 2005 van just like yours I’m getting ready to build mine out

Always run it wild and trim hell yeah I do the same thing on roofs

Length buddy, not size.

I have 3 different styles of these lol I have 1 of the 2 prong, a 4 prong and a 2 prong with wheels on the back. Definitely a life saver when you need it

The demo deckmate bar is better, you pull instead of push! Pushing is a hazard due to the fact that you can fall forward to where there’s no boards and fall through…but if you’re pulling back you got boards behind you still and it’s super fast

Wow

This is absolutely the incorrect installation process! The locking system needs to go together at an angle, then you take a couple taps to make sure the locking is fully in place. Installing lvp like this will break the locking system, and no manufacturer will warranty the floor

Definitely can pour, good job on the self leveling

STORM DOOR HACK. But I cannot see wth you’re doing

Except for it didn't drop in.