Видео

So cool!

That looks awesome!!! Always top quality from DreamwoodRings!

Thank you for showing how to create without expensive tools! Made my first ring and it’s not perfect but neither am I 😂 Time to practice now!

Beautiful ring! I loved your video

What kind of glue is this?

4:10 How are you able to rotate your ring while it’s engraving? I have a design idea but I’d need to be able to fully rotate my ring

You need to do a full dip in UV resin for a complete coating and then set it all in one go. Can then file/sand it down a little bit if its a bit thick. Gives an amazing finish as its a complete coat all the way around in one go 👍

Since there are a lot of comments about the wood "breaking"... Softening "any" wood is best when using a multiple of tricks. But it is always - Water or alcohol, with an added conditioner. There are many things you can add to the liquid if you are having problems. Like, "salt, bleach and baking soda". Heat, time and sometimes "pressure" are your primary variables. (Try using a "pressure cooker" to heat the veneer for a short time). "Especially" with the harder, tighter grained hardwoods. (Like "Bloodwood", Rosewood etc.)! The standard is warm-hot water with a quality "wood conditioner" added to the heated water. "Most conditioners are glycerin based". Ask/call the veneer companies and always shop around"! (There isn't a wood you cannot bend to your will). Well... "Except for maybe old, fully dry-cured, "African Ebony", also called "Ironwood"! Some "Burlwoods", like "Mappa Burl" can be problematic because of their inherent structure, which can cause, "Crumbling" but there are ways around that too! Experiment! Good Luck!

Aghhh! Bologna!😂

1 of 1s know what that looked like at first

Looks nice man, keep creating

Beautiful, What is the glass finish?

This was so helpful! I was so worried that it'd be really easy to scratch through the plating given how soft gold is and how thin the plating is. I know that y'all don't sell them yourselves, but a video testing the durability of the finish on timascus rings (like the ones sold by The Opal Dealer) would also be very helpful.

Great guide! I now know to be careful with sandpaper and just scrape with a high quality carbide cutter. The one ring I made so far with one of your gold blanks held up great and I lost none of the gold! Very high quality blanks! Thanks!!!

I recently go a koa insert ring from you. It is beautiful! Workmanship is flawless! very happy!

Looks great!

Where did y97 get the turquoise blank?

What did you engrave the QR code with and on? It came out very sharp and crisp and the metal was bright underneath.

So much safer than the first way we tried to cut the golf ball 😂

Worth watching until the end, ahaha! At least it didn't fly onto the floor and shatter!

lol the ending

This is great information-thank you so much! I bought all the things but can’t get the darn spindle off my lathe/polisher! Any suggestions? And thanks so much again-you make it look so easy😊

Fantastic

So that's how Oreos are made. 😂

Sad that motherboard still had life to it.

cool

In classic BlendTec style: "Don't breath this."

Stupid 😂

Great job! Can you do it in green and with some chips and resistors or caps on there? Maybe an RFID chip?

I don't make this type of jewelry, but I find the process fascinating. Thanks for sharing.

where o you get the gold blanks

can the carbide tool scrape off the ring finish

My 10/12 mandrel is now in pieces because I couldn’t remove a ring project. I was using CA and the ring was stuck in several spots.

So this is what the Jedis ended doing after the movies Always wonderd~ don't know never seen a movie

Dude! I’ve been doing this for years and am so glad I did.. SOOOO much easier 😉

Should have heated the razor blade

are you saying that you use the jet wood lathe for rings? and use the metal or the 3d mandrel on them? good video again!

love the video and your ongoing commentary. did you remove the black finish? it looked like that when you finished polishing! i thought that was a no no. i have not been able to do a plated ring without taking off the polish. maybe i am seeing this wrong. help me out please. nice looking ring no matter. if the black plating has been removed is that a bother to the customer? do they notice? thanks in advance for your answer.

Great video, thank you for sharing!

I have a tungsten wood and opal inlay, how do you polish and buff these rings to bring them back to shine? I was told it can not be by a jeweler because it has resin on top?

beautiful rings! informative. :o)

Looking to move into ring making at that was very informative Thank you

What type of lathe do you use?

On the 8mm ring how wide is the channel opening width?😊

Today I learned….. Multiply diameter by Pi to get the circumference. It’s only taken me 60+ years.

Lol nice video!

pretty ring can you make the channel if you don't have a lathe

Ever made any of these rings without a lathe and carbide?

мастер,золотые руки,мне просто необходимо такое кольцо!

What is that glue?