Видео

mine sucks, doesn’t shoot 5.56 it gets stuck in the chamber, 233 runs like a beauty but all i have is 5.56

Honestly, I’ve never really understood why people would add this to most firearms. I don’t think I’ve handled a modern firearm that seemed like it didn’t have adequate grip texturing. I’m just checking this video because I’m thinking of buying a pistol that somebody has already added grip tape to. Alcohol is good tip. I probably would’ve gone with acetone, but I’m afraid that that would maybe screw up to finish the polymer.

Wait, so if you were to P/W it, you'd drill into the actual barrel instead of the threads? And you'd be able to see the pin because the ID of the barrel shroud with the pre drilled hole is larger than .740 - .750 ?

Excellent prep work. I've seen many others remove, imo, entirely too much material

bro this video has held for 6 years, thanks for the awesome review.

i’m sorry…. BCM is considered a BUDGET BUILD AR¿?????!!!! i just spent an entire month’s rent on one of these BCM upper receiver groups. i’m moving up from Aero Precision. and you’re telling me that I’M STILL A POOR!?

FUNY no one shoot a flash hider in the dark to see if works or not

Some lady gave me this for free when I was selling her windows for her home. I accidentally left it on sitting with the light side facing straight down, standing up and it died overnight. I got new batteries and it seems dimmer. Any thoughts?

Actually the mesh pockets are 4 independent pockets, they don't pass through (at least not on mine). Thank you for the video!

New trigger pins seems a bit too large can I use original pins

Actually good video Both packs missing anti sway strap thanks to 511 You left out the extra straps on the 10 moab

Of course I realized that this is an older video, but looks like the parts have not changed from what I can see. What I HAVE seen installing this exact barrel with this exact enhanced upper, is that the barrel is VERY TIGHT in the upper, making it IMPOSSIBLE to twist it and hear that nice "tap" when the index pin falls in the groove. Although there may be more than one solution to this, I heated up the end of the upper receiver with a heat gun (NOT a torch!) and the barrel, that was cool, slid right in. Also, I marked the end of the Geissele Automatics Reaction Rod at the back of the upper receiver with a scratch awl, using a completed upper that I know is assembled correctly, so I know FOR SURE that the barrel index pin is in the slot and all the way in on the new build. You cannot directly visualize the index pin after install on the Enhanced upper receiver. BTW, I love these Aero Precision enhanced receivers and these barrels. It is the only upper I buy now for AR15's.

I had the same issue a few years ago on a AR10 build with an Anderson lower parts kit. I engaged/disengaged the hammer and trigger manually for approximately 30 minutes and it works flawlessly till this day. Turned out to be exactly what you said, a burr.

ruclips.net/video/-hSmtLVESSM/видео.htmlsi=4t9XZFoo-5RpMDdp

The pack is great but man did they phone in the main compartment.

How do i find replacement set screws i lost one?

Love that all black!

The barrel length does not factor in

I put these on my old trusty g22 about three years ago. Absolutely hate them. The front sight needs a round dot instead of the entire face being green, and they shot six inches high compared to the oem and the trijicons that were on it. The face of the rear sight also reflects light which draws your eyes off the front. Cool idea I guess, but I’ll never buy these again.

Starting to feel bloopers are a necessity😂, you guys make It seem so easy lol

I torqued bolts on gas pipeline for 15 years. Quit over complicating this. Range is 30-80#. Set it to 45#. Torque it at whatever angle you want. Oh, by the way, did you forget about the coefficient of friction? If threads are dry or lubed, and the different lubes have coefficients too. Whatever, 45#, torque it!

SPEAK ENGLISH DOC WE AINT SCIENTISTS

Best flash hider on the market

so put the armorer's wrench 90 degrees with the torque wrench to get a closer to accurate value?

once I tighten the flash hider, the pin hole is past 6 o'clock, probably around 8. should I keep tightening for another 300 degrees to further crush the washer and get the hole to 6 o'clock? I'm afraid to damage my barrel

Been with me 16 years and counting been to hell and back with me if you know you know America you buy the thumb holder with clip you look like a olight person lmao

I have the same shirt but grey 🤙🏻

Good review

The wrench is already 90 degrees. The diagram you shown is when the wrench is straight but the wrench on the barrel nut is already 90 degrees so you’re applying incorrect torque of 180 degrees. Keeping the wrench straight and the hook is at 90 degrees is correct.

Same here it's an Anderson lower. So good thing I bought a lower m&p full kit. I already had to replace the buffer tube spring and pin. And couple other things

Bro thank you! This was something I never realized I could use to practice

Can you please do a updated video on the barrel and more barrel specs please

All that and no shooting. Smdh

Shooting 223, even match grade out of 5.56 barrel will not result in good accuracy. Unless your barrel has 223 Wilde chamber. But either way sierra bthp bullet will do the best. Also 5.56 is naturally inaccurate comparing to 223 chambered gun. Shoot 5.56 ar Because you’re tactical bros. Shoot 223 if you care about accuracy

You can keep a water bottle inside the gun pocket.

Great vid🤙

thank you so much for doing this using your time and $$money$$ for everyone so they can save their time and money. I will leave thumbs up and subscribe in exchange

I’ve used this pack for many years and it is still rock solid. I use for an everyday work bag and use it very often for my overnight camp bag for my hammock. Love it and I’ll be buried with it.

I have this exact rifle and is missing a sling mount for the barrel section. How do you mount a sling near the barrel?

Great video. Well done. . Crazy thing is, there could be several odd thing resulting ur issue as I am dealing with same. Exact same on the 300 blk out build currently under way. These gun are great once tuned however, smaller precise tolerances just equates to high probably for failure.

ME WANT STICK GO POW POW NOW! Ò🫦Ó

I just bought one so that I can open carry but now that I'm looking at it in my hands I'm not sure if I should seems a little chunky😂 it is a very good quality holster though do you guys (people who open carry) go with or against this holster being used on a carry belt?

I got my handguard just now and realized I didn't get a barrel nut, is this normal?

What are the included straps for?.? The tier system straps

Did you ever do a follow up on this barrel's accuracy testing? I couldn't find it.

Can you name the soundtrack at 2:30 please??

Make video how bag looks after years of wear but for now fully loaded condition too patches etc..

Such a detailed video but didn't even mention how you drilled out the area for pinning the gas block.

But how do you remove that stock

any more videos coming up??