Видео

Shame on Garmin to be selling inferior transducers. My GM 20 is only 2 seasons old and my Garming 5 striker is unable to connect with the transducer. I had a Raymarine before without any problems for years until it was stolen off the boat. Garmin should do a recall and replace FOC

Hola hoyga una pregunta tengo un motor 250 yanaha 4 tienpos con un problema me abienta aceite porla tapa deatras del respiradero despues deacelerar de media makina sino lopaso demedia makina no meabienta kepodra cer ya lepucimos anillos nuebos y ules de culata nuebos

Awesome video! Were you experiencing symptoms or was this just for maintenance?

I agree with ATR-42 Really grateful for your efforts. The part number help and all is great. I will say there is a super helpful and very simple way I've found to dispense ATF fluid. Use a piece of small tubing 1/4, 3/8, 1/2... as an artesian well kind of setup. Drill the cap with a uni-bit. Carefully drill it out to just slightly smaller than your tube. Cut at an angle on one end... makes it easier to push the tube through the cap and also allows the fluid to flow through from inside the bottle. Push the tubing all the way to the bottom of the quart bottle. Now you can simply squeeze the bottle of ATF same as Ketchup. Also, 3/16 or 7/32 drill through the top spout of a Dawn dish soap bottle and 1/4 tubing works great this way.

No bathroom?

You missed one

You should ask about the 40k dollar mark up from invoice on these boats. Dealers don't do much outside of taking money out of your pocket for minimal service.

Do you know where the location of the pressure valve control.

Thanks for the video, I just built my first rod leash and will work on my second one tomorrow. Very instructional and easy to follow. Thanks for sharing your knowledge and expertise!

Amazing, exactly what i need. I have a strange issue that i hope could be dolved by cleaning out the vst. I have a 2011 f250d. Its mounted on a Phantom 21 Speedboat. When i take it out in larger waves and jump with it, or get alot of movement. Suddenly the engine doesnt wanna rev past somewhere between 4000rpm and 4800. Differs from everytime. It runs perfect up to that rpm then it bogs. Seems like it wont get fuel to rev past it, no warnings or anything. Then i stop the engine, pump the fuel bulb, and restart, usually that fixes it. Then it happend again next time i get alot of movement on the boat.

Another excellent video! Watched this tutorial and realized I didn’t have an o-ring! Ordered what I needed and got this simple job done. If I hadn’t watched your vid the old o-ring would have went back in! Thank you so much for the great detail in your videos.

Thank you for an awesome video! Just completed timing belt and t-stats on my VF250LA. Your video gave me the confidence to diy! Thank you sir!

Somebody please tell me why you cannot simply just wire brush those anodes and put them back in. They show almost zero wear, only sea water crud. YAM wants stupid money for an anode. Made of quite possibly the shittiest metal on earth. Were they a buck or two a piece? SURE, toss em.

Excellent video! Was even easier todo than shown. Just had my starboard 2023 F300 with only 260hrs shutdown and refuse to restart. Figured it was the fuel filter, watched your vid, changed it in literally less than 5 minutes and we're back up and running. Thanks

What makes filter fill up and leak down half way..fill up and back down. Every 30 secs it fill to top and back down

Great video, where did you find the snaps with the 8/32 ss screw (bolt). Can't find it anywhere, thanks for any info you can give. Giles

Well done! 🤩💯

Got a Cobia as well. Same pump went out after 2 years. I’m doing this!

F me, the 2 strokes are a dream to service compared to these 4 strokes.

Awesome thank you

Love pursuits but the OOS models

Is it my eyes, or does the knife need sharpening?

Does this affect the 360 view on the camera display? Do you still get the side view cameras as well? Curious to know what camera views this affects by relocating. Thank you.

question, at how many hours is this service done

excellent no music no bullshit just the facts , perfect

Well done! I’m installing a new raw water wash down system and appreciate the reverse freshwater rinse add-on.

Looks like he changed out perfectly good anodes…..hardly consumed at all. If you flush your engine after use, I would not recommend this anode replacement…vastly far higher probability of engine damage and oil leaks. If your boat sits un flushed in salt water….different story.

WHERE would a SK 2 go?

Great idea and video, I am using your idea. Thank You!

thanks for helpful video , i did not know there is another filter inside the tank got to change it just over 1000 hrs

Does your aluminium roller spin with the plastic sleeve or just the plastic?

How heavy of a sinker are you using? I see party boats using 8-12oz.

Great video I’m assuming the same tailpipe would fit for a 2024 2500 HD Chevy midnight edition gas burner also I’m assuming it did not mess with any of the O2 sensors by any chance did it improve the gas mileage due to the no restrictions that the factory exhaust has could you put a link in the description for that exhaust?

Starter plus og minus sikring kaput spørgsmål om hvor for sikring kaput

Doesn't RPM factor in to water pressure? What's the port vs. the star engine RPM?

Is this the first time doing this? What's the service interval for these filters?

Everglades with the highest deadrise for rough weather in the industry 25 degree

Whole baked ling is incredible.

Does the mount wobble or have free play in heavy seas? I am debating whether to use the shuttle slide, or just mount the motor directly onto the deck.

How long should it take a seasoned machanic to replace Internal Anodes on a Yamaha 4.2, 200hp V-Max Sho. Year is 2021. 500 hour service.

Thank you for sharing! I found the sound underwhelming and will stick with Corsa....

Did your kit allow your mirror to display rearview when in drive

Howdy sir. I am strongly considering this system. Are you happy with it in all aspects? If you had the ability to build something similar your self (which you may), is there anything you would change about the design? Is this system full extension? For the price, it is toeing the build vs. buy line for me. I'm interest in your feedback. Thank you in advance.

Awesome video! If I’m just doing the check valve and filter on the top of the vst, do I need to remove the whole tank? Jumping on that this morning.

great idea ! a stainless spring clip might also work

ماشاءالله

I'm just a little shocked that Yamaha couldn't design a simpler approach to replace these anodes. I can't believe they couldn't come up with a better design than putting anodes under the valve cover. I'm guessing they bank on most people not replacing these and motors lasting much shorter than a "smarter" design. Thank you so much for this very detailed video on how to DIY. I guess I will have to go look to see how often this replacement has to take place. I only have a bit over 100 hours at the moment and am in salt water about 10% of the time.

Very helpfull

Is this the GM Borla accessory exhaust or S-type for the 6.6L gas? Thank you.

Very detailed video, thank you for sharing this.