Видео

maybe your buck converter cant hold the current i guess

When they made the original pattern out of wood to cast, those edges weren't sharp for a reason. If you want to cast the solid approach seems best here.

I get the same issues and am looking into heat management

Can this system be run with a higher watt inverter? Like he uses a 300w but could you technically run a 1000w or 1500w inverter on this? I know the power would drain faster. But these are power tool batteries designed to run fairly high demand appliances, I would hope you could at least power a griddle for a few hours or so

Why buy this when you could just get the inverter that also has USB charging?

Did it hold up while spinning at 1800rpm?

Which software you use to find the difference in the model and scan

Why is it important to use the same batteries? Ryobi batteries have internal battery protection circuits, so they should just drop off the array as they get low.

Same issue I’m having with the same model I bought from OfferUp. Not a big deal, the companies gone but I know how to build an ebike. The frame is the important part. Thanks for the info about plugging it in and just showing green

Good

Looks like a ~20% loss across the convertor. The (honestly too many)USB sockets etc would likely use a small amount of current when energized too. For a cheap convertor this isn't surprising.

The words UP TO mean a lot here. UP TO 80% faster than other charging methods. Now if you think harder, what's the WORST way to charge these? Oh yeah, 500ma USB ports exist. Reading and thinking are awesome tools.

Youre inlet needs to be LARGER than your outlet. PLUS, the inlet needs to be mounted low to draw in cool air while the outlet is mounted high to collect & discharge hot air. REMEMBER Hot air rises & cool air sinks. !

I can’t believe it doesn’t have pass through charging. Why does ryobi keep doing this

Thanks for this. I had this in my hand yesterday. 2 pack of 3 amp batteries. Put them back. But now i want the batteries but not the charger.

How did you assure that there would be adequate air flow for intake at the unit? attach a tube that accessed the open air of the isle? frame in the area with a screen in the isle? If a tube was used, what diameter? thank you very much!!

Question may you please list some cheaper solar charger controller under $50

When coming out your side slider, do you come out backwards or does the step pull out far enough that you are able to safely come out facing forward? thank you

Can it detect foundation dimensions?

We will be putting the same heater on a 2023 promaster. Can the heater drain the gas tank or is it set to turn off with 1/4 tank left? thank you

Very helpful!! Hopefully, we will be doing the same thing soon. I heard you have to be very careful of the slope of the fuel line. Did you have problems with this? thank you

Omg Arlo, Archie, and scout are the cuteeeesssttttt! Like like like 👍🏽

Where I live recerticication is less than $10 on those small tanks. Cenex recertified my 100 pounder for free when I filled up. This made me wince a little bit.😢

Great Video! thank you for the info.

Use compressor to flush out propane from tanks. Better to be on safe side

Any idea on charging this workx 24v directly

What a waste of propane tanks ! Could have returned them for full tanks at kiosks for propane tanks at Home Depot and other stores

Thank you

Could you make this solar charging capability?👀

Nice video. Are you on e bikes?

They are so nice 🎃

Just charge by electricity at home and put roof top solar panels, no need to spend huge money on these especially if you use your tools at home. Those solar blankets and Mppt charge controller are junk and unnecessary.

That’s awesome! Burn a road flare in one of them!

A 4" hole saw would have been faster and easier than the jigsaw?

Coupler! Not coupling.

Gotta do same! Just bought the engine at Harbor freight. Better go get 12 washers, and some oil. Remember to use only gasoline. No ethanol low grade pump stuff. Real gas can be bought at Sunoco.

The ac adapter is also Mppt, you can just connect 3 panels in series directly to the ac adapter, it doesn’t care if it ac or dc as it is SMPS supply.

Very helpful and well explained. Exactly where I was planning on installing mine.

You are a freaking mad wizard. I love it.

When scanning parts to be 3D printed I use monochrome mode, as colour mode significantly increases image processing with no practical benefits. Recommend printing high speed 3D printed parts in a carbon fibre impregnated filament to withstand high centrifugal forces. 👍

I know this is several years old but does anyone out there still have a port with the main board intact? I had a diode burn up and can't id the part number on the diode to replace it. It's listed as zd401 on the PCB.

So how many of those to charge the 40v battery? I would like to run my bussines with mostly battery equipment

Do you know how to get power out of the Bosch battery for other purpose than the bike ?

That's. High power microwave . Normal. On 20 amp. Independent. Circut it. Run. Small. Power microwave. 15 amp .. like. 1000 watt. Or below.

I wanna print those vents please pass us info. Great size great video

Thank you.... very helpful!

What size is your fiamma awning? thank you

thank you sooo much. I am short and just got a promaster!! really need a solid step

Good work, thanks!

If you used a USB 2 Type C cable instead of USB 3 type C, I bet it would charge a lot more slowly, because USB 2 didn't support nearly as much power as USB 3.