Видео

Saved me! Thank you! (2003 Civic)

That happened to mine for a quick second and the holes popped off inside the machine all I have to do is unscrew all the screws on the machine and I saw the holes was off so I pushed it back on and put a hose clamp on it maybe that's the same problem of yours if not I recommend to open up the machine with all the screws that's around it and see what's going on inside the cover

i have the same problem

Thank you helpt me out a lot

Thanks for putting this video up it really helped me do this job myself and was actually not to difficult with your instructions and hints and tips👍🏻

Hi I have the EGR sensor 2 Fault on my 2007 1.9 7H T5 - it runs fine but is very smokey before it warms up - then its fine - runs smooth and fine other wise? could this be the EGR cooler? #

Thanks for these video Andy , Kind Regards

Please help me

I need some spare parts of hyundai grand starex 2015 model vehicle how to purchase it online can you give me your whatsapp no.

Hello, where can I buy the lights please?

Hello , where is ur garage?

This video would be a lot better if you had shown us how to ... 1. take of the cover of the centre housing, and 2. how to adjust the handbrake cable. Other than that, all you did was show is WHERE to find the place to do the job.

Saludos amigo tengo un problema con starex 2016 no tiene presión en el riel

I can help you

had this happen on 2 different occations with different reasons for it . first time was spark plug on cyl 4 was almost dead . 2nd time air inlet hose to turbo was beeing sucked flat under load

Thanks. I came here to see how to release the clip. 4:56

Just replaced my EGR & cooler on my T5, using your video. Great help, couldn’t have done it without as I’m not a mechanic so thanks very much 👍(it was still bloody awkward though).

Dead battery

FUKING BMW IDIOTS CRASY THAT !!!!!!

Thank you. My handbrake has gone completely floppy 4th time in 2 years. Keep taking to garage. Will try this before I take it again. Emma

Just done this! All good until I dropped one of the T30 Torx bolts into the engine bay, it didn’t hit the floor so it’s lost forever! Now I need to buy a new one, it’s one from the flexi pipe at the front right, anyone know the size?

Excellent step by step guide, changed mine no problem. Got the replacement part from Amazon £190. Garage was going to drop the engine to replace, so this video saved me ££££'s So many thanks. You look a little like the actor Simon Pegg by the way😁.

Hi I'm thinking of cleaning rather than replacing, but the gasket between the Cooler section and the main valve body isnt part of any set of gaskets that I can find. Even tried my local motor factors. Can you usually re-use the existing or can they be obtained?

I changed mine yesterday thanks to this video. The only thing I did different was remove the pipe round the back to access bolt. Because I couldn’t on it. I have very little mechanical experience so thank you very much. Just one question. I reset the EML light, do I still need to get it plugged in and formatted?

What a ball ache just to change a filter🙄

Great video! You have saved me a lot of £££'s from what it would have cost me if I had taken it to the garage. A BIG thank you.

Good job, I've had the same problem on my Pathfinder !!!👍🏽👍🏽👍🏽

Thanks for the video. It saved me quite a bit of time to figure out how it all goes together.

this video has saved me a bloody fortune .. my pathfinder broke down on motorway lost all power had to be towed home did all the checks even got new fuel filter new suction valve on pump blead all the fuel pipes the lot.. still didn't know why it would not run 'I'm no mechanic but if i can do it myself i will have a good go .. and then i saw this video and bang off came the EGR valve and what to my amazement i saw the dead same thing broken valve it had come off and got stuck in the open position so plated over valve and bang back on the road fantastic THANK YOU FOR POSTING

Thanks nice job for tomorrow

The shetiest engineering design ever for a part fitment. I hope the new models are not installed the same way. If they are, means engineers are really dmb, man!

Jeez……couldn’t they make it any harder ? I’ll let the garage do it.

On my 750 I don’t even put the two Bottom screws on , this car just doesn’t make any sense I’m sorry.. engine gives problems, recall lawsuit , trannies go bad , wheels bend easy, gas guzzler, light bulbs are burried only thing it gives a good ride that’s it

Very good master

at 2:37 you simply slide the electrical connecor off, i tried it all now, im about to get the hammer are take it off viking style!

Thank you! I messed with this plug for a hour until I finally found your video.

Thank You for this video. Gonna swap mine tomorrow

The thumb is showing the LCI with Adaptive LED not the HID you are doing this work on... suggest update the image

Great Video thanks for sharing over 4 years ago. Can i ask when you say 'Adapt it back in' Do you mean just follow the VCDS instructions you included in the video to code it in? Sorry just want to know what Adapt back in means. Also did you torque the screws back in or just screw back in firmly? Thanks

What a Guy Andy , so helpful , mine is done, 2hrs roughly .Get this then !!! vw centre Peterborough 1200£ robbing Bast***s. should be ashamed.

Attempting mine this weekend🤞

So the normal driver won’t be able to change a light bulb any more. It’s crazy. I would bother to try it. Leave this to the pros. Thanks.

this is not a mk3

Are you serious.. just to replace a headlamp bulb you have to go through all of that.. that's crazy BMW really made sure their car was inconveniently design to perform simple tasks all the way down to a headlight bulb...I could see if I was trying to replace the housing but geez

Similar a la VW Amarok?

Thanks pal Saved me a few quid 😉

DON'T TAKE THE HEATER OFF..... SIMPLY UNCLIP THE WIRE FROM THE BACK OF THE HEATER

Thank you. Great video.

What I can see this guy know what he’s doing

The press on its side is epic!