I was thinking about giving up learn inh electronics (I have just started, learning basic components and laws), but after seeing your videos I decided to give it a try. You give the list of components, give clear instructions and explain everything so well and even reply to the comments. I think I may keep up to it with your channel :) Also, this robot is amazing! Cuteness overload
@@SongShixuan Thank you friend for the comment❤️🙂 Making projects with Arduino microcontroller is relatively easy and needs only basic electronics knowledge. There are lots of interesting projects to make and our imagination is the only end to it. So please don't give it up. Start making basic projects and slowly you will find yourself to be able to do all projects and its coding with ease.Wishing you the best!!!
Hi friend, you have to check the connections. Is it going only forward and not backwards when it sees an obstacle?. Sometimes the ultrasonic sensor may be faulty!!!
Do you have an Amazon link to buy the screwdriver to fix the screws in the legs? (we tested several screwdrivers, each time the screw fails and we can't screw enough for it to hold well)
@Jonathanquesnel I am sorry friend. I used a screw driver that I got alpgwith the toolkit while purchasing a 3D printer. I know the screwdriver needs to be long and also should pass through the hole in the legs to tighten the screws. It is a littlebit tricky and not possible with all screw drivers. I am sorry that I dont know the purchase link for the screwdriver.
Thank you friend for the solution. I have also found out that using 6x 1.5V AA batteries also doesnt cause the restarts as each AA battery is rated for 2A peak current!!!
@@paziproductions Yes friend. I connected to 5V pin on shield. But it was not working properly. The 2x 9V batteries are not able to provide enough current for all the motors to work together. I used even 4 x 9V batteries which were also not sufficient. It will work for a few seconds and the nano will get reset due to drop in voltage. One possible easy solution is to use 4X AA batteries. They have higher current rating and I have read that it will work. I have not tested though.
I was thinking about giving up learn inh electronics (I have just started, learning basic components and laws), but after seeing your videos I decided to give it a try. You give the list of components, give clear instructions and explain everything so well and even reply to the comments. I think I may keep up to it with your channel :)
Also, this robot is amazing! Cuteness overload
@@SongShixuan Thank you friend for the comment❤️🙂 Making projects with Arduino microcontroller is relatively easy and needs only basic electronics knowledge. There are lots of interesting projects to make and our imagination is the only end to it. So please don't give it up. Start making basic projects and slowly you will find yourself to be able to do all projects and its coding with ease.Wishing you the best!!!
Superb work ❤
Thank you so much..🥰😍😀
Superb work sir🔥🔥🙌🏻🙌🏻
@@gokulsree5861 Thank you..❤️🥰👍
@@gokulsree5861 Thank you so much..❤️🥰🙂
Excellent work
@@anilgeorge2062 Thank you so much..❤️🥰🙂
In obstacle avoiding car the bc moter not going rivers pls tell me solution for it
Hi friend, you have to check the connections. Is it going only forward and not backwards when it sees an obstacle?. Sometimes the ultrasonic sensor may be faulty!!!
Do you have an Amazon link to buy the screwdriver to fix the screws in the legs? (we tested several screwdrivers, each time the screw fails and we can't screw enough for it to hold well)
@Jonathanquesnel I am sorry friend. I used a screw driver that I got alpgwith the toolkit while purchasing a 3D printer. I know the screwdriver needs to be long and also should pass through the hole in the legs to tighten the screws. It is a littlebit tricky and not possible with all screw drivers. I am sorry that I dont know the purchase link for the screwdriver.
@@Science_4U_ I found you have to use a PH00 screwdriver.
i also faced similar problem the simple solution is to use 2s lion battery pack . the insufficient current leads to restarting of arduino
Thank you friend for the solution. I have also found out that using 6x 1.5V AA batteries also doesnt cause the restarts as each AA battery is rated for 2A peak current!!!
Sir Can you give a video on wifi controk car with esp8266 and l298n module
Pls 🙏🙏
You connected the 9V positive wire (red, switched) to the 5V pin on shield?
@@paziproductions Yes friend. I connected to 5V pin on shield. But it was not working properly. The 2x 9V batteries are not able to provide enough current for all the motors to work together. I used even 4 x 9V batteries which were also not sufficient. It will work for a few seconds and the nano will get reset due to drop in voltage. One possible easy solution is to use 4X AA batteries. They have higher current rating and I have read that it will work. I have not tested though.
Sir, can you make a Human following robot with Ultrasonic sensor with easy coding as you give 😊
Okay friend. I will make one day..👍
Hello, hello follower, could you share the code please?
Hi friend. The link to download code is given in the description box.