Yes!! I hope I can get as good of results. I realize Ty or AKA beginner to edge of Master Apprentice has skills in a short period of time. I hope that I can be so lucky!! Thanks for sharing and for all the hours it takes to make one of these videos!! I love that you dint exit out Ty on his own after you went to the office with clients!! That means you trust your employees to have the knowledge to get it done right. Thank you!! Whooped it Ty!!!
I’ve learned some much watching ur videos. I’ve also watched every video u have put out. I’m doing some polishing here in Nashville Tn. I still have lots to learn.
Love the videos!! Great job!! I believe watched every video that you’ve put out. Can you make one on how to polish the rails of a trailer with the chicken lights installed? Thanks
How do you clean and polish a 1980 autocar constuctor has never been cleaned for 30yrs been in a coal mine is it looks like a old soda can he on a budget
Hey Evan, I'm.wondering about this I have an 2011 honda odyssey aluminum wheel I'm sanding faulty clearcoat down to 600 grit and polish with mothers polish and then clearcoat 5 coats to offer protection so raw aluminum is not in the air. I'd rather leave the polished surface but presume it will oxidize quicker with no protection. So I clearcoat and the shine then comes from the clearcoat vs all that nice polishing. What do you think am I doing the right thing?
Love the videos. I've been doing alot of metal polishing myself lately but the one question I have is that I see alot of you guys using 6000rpms instead of the 3500 variable speed. What flanges are you using because the zephyr one is only rated to 3500???
@@EvanStegerMetalPolishing man I wish I knew what I’m doing wrong. I’ve tried sanding first and without sanding and I just don’t get good results. I put hours and hours into polishing my truck and the fuel tanks came out ok but the grille looks basically like I never touched it. Y’all make it look so easy on RUclips.
We only remove the safety start tab. The lock feature is still enable able but we just don't use the lock in our shop very often. We do have a video on how to remove the safety start tab though if you need it.
Shimmy shimmy shimmy, blah blah blah. No disrespect Ty, but you polished that grill twice already and it’s not very shiny until this time. Makes me question your mentor. Shimmy shimmy shimmy, blah blah blah. Say, what’s that red goo behind you? Shimmy shimmy shimmy, blah blah blah. 🎵🎶Don’t push to hard or you will leave scratches. Shimmy shimmy shimmy, blah blah blah.🎵🎶Chunky and blah blah blah
Great work enjoy seeing credit given to someone like ty that may not get recognition for there hard work. Keep it up guys
He’s come a long way whole working for us. He’s really getting good.
@@EvanStegerMetalPolishing how long has Ty been with you guys?
Love to see a young kid with ambition. Stick with learning Darrel and you can be anything you want.
Truth
Yes!! I hope I can get as good of results. I realize Ty or AKA beginner to edge of Master Apprentice has skills in a short period of time. I hope that I can be so lucky!! Thanks for sharing and for all the hours it takes to make one of these videos!! I love that you dint exit out Ty on his own after you went to the office with clients!! That means you trust your employees to have the knowledge to get it done right. Thank you!! Whooped it Ty!!!
He is definitely talented for sure.
@@EvanStegerMetalPolishing keep up the good work.
This is awesome! No one remotely close to me polishes anything beside rims! This is so helpful! Gonna do ot myself
Thanks for watching. Glad you enjoy the video.
Tyrese just took over the show! GG!
He was good at what he did.
I’ve learned some much watching ur videos. I’ve also watched every video u have put out. I’m doing some polishing here in Nashville Tn. I still have lots to learn.
That’s awesome. Thanks for watching.
No problem I enjoy watching and hope to be good at it like you guys someday
I'm glad you like the videos. Truly appreciate you watching.
Awesome. Iv been watching a lot of your videos Iv learned a lot. Trying to get have as good as that young man. !!
Glad to hear it. You'll do great. Thanks for watching.
He did a awesome job.
He sure did. Thank you.
Good job Todd 👍🏾
Ty’s a great kid. I’m grateful for the lol guy.
This is awesome! Killer job ty! You have a good teacher.
He's come a long way for sure.
Doing good he got it better than when I started
He's learned a lot and come a long way. Grateful to have this kid with me.
@@EvanStegerMetalPolishing true I can see
Stay Smooth Ty! Loved the video!
You too! Thanks for watching.
Looks amazing Ty. Love these vids. Nice work guys!
Glad you like them! Thanks for watching.
Great video as usual .
Thank you. Ty is a great kid and learned a lot.
Good job. I just got into polishing and it’s awesome!
Good to hear!
Good stuff Ty!!
Awesome shine bud👍🏼👍🏼😎
Thanks for watching. I'm super proud of him.
I was hoping for a video that would show off the 40 ply domet...I think I need to buy it now lol good job Ty!
Ty has grown so much. I'm so proud of him. Thanks for watching.
The goat thanks for the info.
Glad to help.
Great job Ty!
So proud of this kid.
Love the videos!! Great job!! I believe watched every video that you’ve put out. Can you make one on how to polish the rails of a trailer with the chicken lights installed? Thanks
Take the lights out. You’ll be happier if you do.
Ty did a awesome job till him to keep it up and you too
I will. Thank you bud for all the support.
Slime did a great job!!
agreed!
Good job
Thank you for watching.
kid a natural!!
He sure was.
Great job
Thank you!
Good job!
Thank you for watching.
How do you clean and polish a 1980 autocar constuctor has never been cleaned for 30yrs been in a coal mine is it looks like a old soda can he on a budget
Hey Evan,
I'm.wondering about this
I have an 2011 honda odyssey aluminum wheel I'm sanding faulty clearcoat down to 600 grit and polish with mothers polish and then clearcoat 5 coats to offer protection so raw aluminum is not in the air. I'd rather leave the polished surface but presume it will oxidize quicker with no protection. So I clearcoat and the shine then comes from the clearcoat vs all that nice polishing. What do you think am I doing the right thing?
Most clear coats won't stick over proper polis. You'll also need more than mother's polish over 600 grit. Mother's isn't very abrasive.
Awesome job only could keep getting better
He was killing it. Too bad he quit. He was a great asset.
@@EvanStegerMetalPolishing good help is hard to find these days ....hope he had good reasons?!
@@geronimo55kj I wish it was a good reason but you are right. Good help is very hard to find. Especially in this industry.
Thanks for sharing
My pleasure, thank you for watching.
Love the videos. I've been doing alot of metal polishing myself lately but the one question I have is that I see alot of you guys using 6000rpms instead of the 3500 variable speed. What flanges are you using because the zephyr one is only rated to 3500???
goshineon.com/shop we sell the all aluminum insertable safety flanges that are rated for higher speed. Thanks for watching.
@@EvanStegerMetalPolishing gotcha thank you sir
So for the grille can u just use the orange and brown and yellow and green or do u have to do it the way u guys did it
You can do it however you want. Our videos aren’t guidelines. They are videos of how we do it. Many do it differently. And that’s ok too.
Great job Ty thanks
Thanks for watching.
Where can I buy the “loose white” wheel he used to buff out the hand polish?
goshineon.com
Was any sanding done on the grill before hand?
Not on this particular video. We avoid sanding as much as possible.
@@EvanStegerMetalPolishing man I wish I knew what I’m doing wrong. I’ve tried sanding first and without sanding and I just don’t get good results. I put hours and hours into polishing my truck and the fuel tanks came out ok but the grille looks basically like I never touched it. Y’all make it look so easy on RUclips.
Can I call him Ty the new polish guy?
You sure can. I'm hoping to involve him and many other polishers into this series of videos.
Do you modify your triggers so they dont lock?
We only remove the safety start tab. The lock feature is still enable able but we just don't use the lock in our shop very often. We do have a video on how to remove the safety start tab though if you need it.
Was that a 3 or 6 thousand rpm grinder?
For cut we use a 6,000 rpm grinder and for finish polish we use a 3500 rpm buffer. Thanks for watching.
DETAILING AND POLISHING GUY
Hello!
What brush or pad is that
goshineon.com 2 step aluminum kit
I don’t know if I’ve ever seen you use a rake on your cut buffs?
I never rake my cut buffs.
Is it brown green and last white?
We finish with green compound
Where can I get a loose white buff?
www.goshineon.com
Cool guys
Thanks for watching.
Love seeing young dudes excited to get dirty and earn that money $$$
I agree. Thanks for watching.
I see orange wheel , brown polish?
Yes most of what we do is orange with brown first.
This is how to polish a grill with ty
Thanks bud.
Where did ty go
He is in the area living life. Thanks for watching.
I was gonna hit the like button, but its at 379 and thought 379 grill 379 likes, I'm not gonna be that guy. Great video though
Thank you for watching and commenting!
Shimmy shimmy shimmy, blah blah blah. No disrespect Ty, but you polished that grill twice already and it’s not very shiny until this time. Makes me question your mentor. Shimmy shimmy shimmy, blah blah blah. Say, what’s that red goo behind you? Shimmy shimmy shimmy, blah blah blah. 🎵🎶Don’t push to hard or you will leave scratches. Shimmy shimmy shimmy, blah blah blah.🎵🎶Chunky and blah blah blah
Lmmfao not sure what that stuff was.