Mercury IV Forced To Land
HTML-код
- Опубликовано: 30 май 2024
- The third flight ended abruptly, I was lucky to be in a good position to make a safe landing, I'll link to the investigation video at the end, the deadstick happens from 12:55, cheers. The plan is available on Outerzone for free download outerzone.co.uk/plan_details.a....
Don't forget to SUBSCRIBE for regular Build and Fly videos using this link ruclips.net/user/CliffHarvey...
SUPPORT 'Cliff Harvey RC Planes' and JOIN HERE / cliffharveyrcplanes for EARLY ACCESS to NEW videos 
Наука
The ESC is the culprit, check out the link in the description for the forum discussion, I've increased the cooling in the cowl and adjusted the throttle curve back to 100% as well as fitting an 80amp esc, all this should sort the problem nicely 🙂👍
Ah the nostalgia. That bird reminds me of the Black Magic design of the late 50s. Rudder/elevator with lots of dihedral and a lifting section is a different flying experience to modern zero-zero rigged models with ailerons and symetrical wings. You can't beat these old-timers on a calm summer's evening when all you need is a click of trim between beers to keep them in the air.
You're spot on there Bruce, the Black Magic was another classic vintage design ... not sure about flying little sozzed though 😁👍
What a beauty, glad you got it sorted Cliff...
Thanks Eric, quite easy to transport as well, the wings have a big area but a short span 👍
Handled like a true pro!
No point in panicking as we all know as pilots, the first rule is to pilot the aircraft, cheers 👍
glad you have got it sorted Cliff, we had a similar problem cured by opening up the exit hole in the cowl...nice model tho enjoy.
I knew the exit should be bigger than the inlet but figured that being the esc was virtually right in front of the inlet it would be ok. When you think about it though the air doesn't actually enter the cowl if it can't get out 🤔👍
Great video Cliff, see a few vintage models clap their wings on manoeuvres 😊.
Im shouting at the screen put a four stroke in 😊. Hope the ESC issue is sorted now.
It's got two main spars/wing joiners Mark, I reckon two of you could sit on a wing tip each! What we actually saw was the wing leaving the body, I'll add a couple more bands in future 😁😁
Cliff great flying, Jeff in LA USA
Cheers Jeff 👍
That is one beautiful aeroplane Cliff, though if it was me I'd be putting an IC engine in it. I'd be tempted to design and make an on-board starter so one could shut the engine down, glide away in a thermal then restart the engine if you needed to bring it home say. Wonder if anyone has already done an on-board starter for a glow engine?
Thanks Aero, sounds like your describing the convenience an electric model 😁👍
Hi cliff just watched to see if I can figure out what’s going on .. pull the motor and remove the rear circlip and separate the bell from the stator .. check the rare earth magnets in the bell to check there not coming unglued wiggle a small flat head between them and just shimmy to see if any move .. sometimes one of the magnets will come Un bonded and slide back making contact with the stator windings and shorting causing a safe cut .. I have had a few motors go that way with strange resetting and cutting power
Hi Jeff, thanks for the info, I've had that happen as well but I do believe it's an over heating esc this time, keep trucking and flying of course 👍🙂
Sounds a lot like, "egads", IC power.
Lol, you're right Gary, shock horror 😁👍
Who designed it Cliff? Is it a Ben Buckle plan?
Mick Smith, I'll add a link in the description to the plan on Outerzone CC, cheers 👍
@@CliffHarveyRCPlanes Thank you Cliff, you're a gentleman.
Something's a bit wrong with the colours in this video, it looks like a camera with no IR filter. I suspect you've taken the ISO mode of the camera out of auto, and set it to something that doesn't make it look right on this particular day. I like slow fliers like this though.
Hi Fraggsta, it was a dull day and I played with the colours in post, it looked ok on my monitor but not so good on the tv ... lesson learned 🤔👍
hey this is off Topic but I need to know what to buy to use with spectrum transmitter when building a minimum rc kit? any way u can help?
Hi Willie, for Spektrum you need a DSM2 compatible receiver 👍
It might be better not to land towards yourself ! nad don't do aros with a vintage model
That's what happens when you stand at the end of the strip Rog! Surely a little loop can't hurt 😁👍