How to Replace Starter 2009- 2014 Ford F-150 (5.4L V8)
HTML-код
- Опубликовано: 7 сен 2024
- Buy Now!
New Starter from 1AAuto.com 1aau.to/ic/1AES...
This video shows you how to install a new starter on your 2009-2014 Ford F-150 (5.4L V8). The starter is a powerful electric motor that gets your engine to turn over when you turn the key in the ignition switch. If a motor has worn out or become damaged, your vehicle won’t start.
This process should be similar on the following vehicles:
2009 Ford F-150
2010 Ford F-150
2011 Ford F-150
2012 Ford F-150
2013 Ford F-150
2014 Ford F-150
🔧 List of tools used:
• 13mm Wrench 1aau.to/oYW/1AX...
• 10mm Socket 1aau.to/obhS/1A...
• 13mm Socket 1aau.to/obCE/1A...
• 8mm Socket 1aau.to/obhS/1A...
• 3/8 Inch Drive Ratchet 1aau.to/obCE/1A...
• Ratchet 1aau.to/obG9/1A...
• Socket Extensions 1aau.to/obCE/1A...
• Swivel
• Torque Wrench 1aau.to/oaK8/1A...
• Gloves 1aau.to/oaju/1A...
• Safety Glasses 1aau.to/oacn/1A...
Subscribe: / @1aauto
For More Info visit us at 1aau.to/h/e87/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Visit-1AAuto
√ Do it Yourself
√ Save Money
Have this ahead of me this weekend. Ordered the starter before this video was published... And happy I waited this long to put it in, this is a really well done video giving me plenty of confidence thanks!
Thanks for showing, I've found in 40 years of wrenching that it's almost always easier to remove the hardest to reach bolt first. Then the easiest bolt last. Just like you did install the easiest first and don't completely tighten any until they are all started.
Thanks for this video, I just changed out the starter on my 2010 f 150. I couldn’t fit my 3/8 ratchet and extension on that top bolt (just slightly too long) and was barely able to break it with the 1/4” but I got it off new one on. Took just over 2 hours to do the job and saved me a few hundred bucks on labour. Thanks again
Your video was very helpful. Took a long time because of sticky bolts, rust and rain storms (I had to work in my driveway), but I managed to remove and install a re-manufactured starter on my 2009 f-150 I obtained at the local ford dealer. You weren't kidding about the top bolt, which I had to feel around by guesstimating the bolt interfaces on the bell housing with my fingers, then guessing where to re-insert the bolt by feel. Lost the bolt once, but found it after purchasing a new bolt and eventually finished the job. Starter worked from the get-go. Thanks!
Thank you, thought for sure the starter wouldn't come out, because so tight in there...but lucked out and repaired the solenoid...appreciate the video..
That top bolt is a mother!! Ask me how I know. Smh
Could you please make video on how to replace the O2 sensors? upstream, bank 1 and bank 2, & oil pressure sensor. Thanks. Like and subscribed already.
Dude you did excellent A +
I'd use anti seize on the threads! Ford should've put bolts on the rear of the bellhousing instead of removing from front.!!!!!!!!
FYI this is how to do it on the older 7.3s to
That top bolt is impossible! Got it out, but it's never going back in cuz i lost it somewhere on top of the bell housing. You can't even see the top one!!!
I did this whole process, installed a new starter, checked every fuse and relay in the truck after that didn't work, finally checked the fuse box in the cab as a last ditch effort and... there was a cable half unplugged. That was causing several issues the darn thing was having. Probably why the previous owner sold it so cheap to be frank.
Was surprised you could get your finger on that top bolt and get it back in place.
Good camera view ing
The best explanation..and with video looking at the mutha😅 top screw!!!!!
Thank you
Why didn’t you just use the swivel?
Sad they cant make a coating to prevent that rust
Your camera is so close that gets me lose concentration
This was beautiful. Thanks U,
+jon c Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
My truck didn't have that room this video has....and I don't even bother putting in the top bolt, impossible