Good job, sir! Have you considered reversing the pulleys such that the larger pulley is on the blade and the smaller pulley is mounted on the motor shaft? The would reduce blade speed (ideal blade speed of 1000-1200 RPM--slower for larger diameters) and increase torque to possibly be able to use a cold cut blade instead of abrasive blade which has great benefits. I've checked into the evolution cold cut saw; but, it's to expensive for me. When I found your vid, I was actually looking for DIY cold cut saw ideas. Good day, sir!
Man I have a huge metal cutting chopsaw, it's just been sitting out back , found it thrown out , didnt wanna throw it away . I have a 115 volt 1725 RPM AC electric motor also dont wanna throw out , runs great very quiet . Then I saw this . Combine them and now have use for both .. thanks
Shit , the problem is , I hurt my back building houses my whole life about 11 years ago it went out and now hurts everyday . So my wife talked me into selling all my shit . Dont even have a dam screwgun , grinder , no welder , i just have the basic toolbox tools now .I'm screwed either way. Ain't been able to work since on the dealt chopsaw I pull button and nothin, like if theres a short or cut wire . My guess is the was cutting metal and pressing to hard to long and burnt it up...
Nice rescue of the dead saw. As many have mentioned, the slower speed opens up other uses for it too. Plus later on you could probably and various size pulleys to open up other speeds for it and even more uses (like the 3 pulley system we used in my high school drill press machines, so we could pick the best speed for the drill size and material))
Amigo yo tengo una sierra circular pequeña q el eje está barrido en la punta pero está al 100 por ciento. Vi este vídeo y veo q sePude hacer lo contrario. Ponerle buena polea en la punta y hacer un mandril pequeño con su correa y se pude utilizar con un disco de 7 pulgadas xq el motor está en muy buenas condiciones
If you change the pulleys to slow the speed down that will give it more toque and then you will be able to use a coldsaw blade and because the motor no longer is so close to the blade you will be able to run coolant with the blade just make a reservoir under the saw to catch the coolant and a small pump to cycle the coolant back up to the blade
Great idea brilliant ..... it gives me the idea of connecting a three phase motor so I can control the speed or maybe an ordinary DC motor .... I am a true hacker hacker hacker ..... I would use a and grinder with a cut off blade and just saw the motor off and then connect a motor directly to the shaft…… And then find out that I really needed to use a belt based solution …… I am really lazy and this causes me too often do more work than I should have had to do
The idea is very interesting, by damaging the original engine, another type of engine can be adapted, possibly the only difference can be the power of the engine or the speed, because the carbons engine has more power and speed, greetings and thanks from Nezaland city Mexico
идея интересная, но на мой взгляд немного надо доработать,вал более жестко закрепить, дистанционные втулки в виде болтов немного слабоваты. и мотор от стиралки, ремень многоручевой .главное что есть направления и идея.космический корабль не сразу полетел.дорогу осилит идущий
The new bearing is not steady and cutting speed is too slow as others said. You’ve got a motor, I believe you can make an other new than use the broken one!
Разговора нет., отлично придумано и выполнено. Единственно что лично мне, не совсем понравилось, это то что из мобильного инструмента делают, стационарный (это я про гриндер). По сути из мобильного, сделать стационарный не сложно, а вот наоборот, задача сложная. У переносного инструмента, наблюдается дифицит мощности и надёжности. Тогда как у стационарного, можно варьировать мощностью. И при выходе из строя одного узла, с лёгкостью можно заменить этот узел. (что кстати и продемонстрировал мастер) тут вес уже не важен, зато ремонтопригодность, выросла в разы.
Use a carbide tooth blade like the famous evolution chow saw and slow down the rpm to no more the 2300 rpm I copied your idea using a treadmill motor and it's the best metal chop saw I have ever used. I use it more than my horizontal band saw
Aqui no Brasil ,farei o mesmo, pois uma policorte Black Decker , queimou o induzido e me cobraram US $ 68 para fazer o conserto . O custo do equipamento novo é US $ 125 !
Why don't you try running a carbide steel cutting blade like the new cold saw Fein Slugger or Evolution saw and use one of those blades on that belt drive saw that you've created there it might work really well the RPM seem to be just about right they're only supposed to be 15 1600 RPM James
Dude when you said you may change out for a better motor in the future...it just hit me.... find an old chainsaw and use the engine from that... gas powered!!... that would be really cool I've got one here at my house that would work well but I'm in the USA
Pekpek fit talaga idol😁😂😄
Shhh. hahahaha
Hahaha lodi talaga🤣😂
Taena hahaha
Thumbs up
Galing ng pag kakaconvert mo bro.
Salamat bro.
AMAZING IDEA! 👍👍👍 😀😀
Great repurpose of the broken saw. Great video
Good job, sir! Have you considered reversing the pulleys such that the larger pulley is on the blade and the smaller pulley is mounted on the motor shaft? The would reduce blade speed (ideal blade speed of 1000-1200 RPM--slower for larger diameters) and increase torque to possibly be able to use a cold cut blade instead of abrasive blade which has great benefits. I've checked into the evolution cold cut saw; but, it's to expensive for me. When I found your vid, I was actually looking for DIY cold cut saw ideas. Good day, sir!
That's a great idea. Good job.👍
Man I have a huge metal cutting chopsaw, it's just been sitting out back , found it thrown out , didnt wanna throw it away . I have a 115 volt 1725 RPM AC electric motor also dont wanna throw out , runs great very quiet . Then I saw this . Combine them and now have use for both .. thanks
Shit , the problem is , I hurt my back building houses my whole life about 11 years ago it went out and now hurts everyday . So my wife talked me into selling all my shit . Dont even have a dam screwgun , grinder , no welder , i just have the basic toolbox tools now .I'm screwed either way. Ain't been able to work since on the dealt chopsaw I pull button and nothin, like if theres a short or cut wire . My guess is the was cutting metal and pressing to hard to long and burnt it up...
galing niyo talaga boss...dami ko nakukuhanh techniques sa inyo.salamat sa pag-share ng ideas.
this build mod i have searching, finally I can see some do it. thanks x sharing. The only man I see doing this
Muito bom parabéns pelo trabalho
Rop
Great! Any time you can reuse make it purposeful again, it a win!
انت معلم اخي ماقمت به عمل ممتاز💪👍
Que buen trabajo, más ideas para nosotros, gracias de Peru🇵🇪
i wonder if you can make a cold saw by changing the gearing : )
Really nice job 👍👍👍
good Idea! what do you think about a system to fixing the motor further to tighten the belt ?
Excelente no tiene mucho ruido...
Felicitaciones.
Saludos desde Perú.
2:23 how do you mark the holes on plate , please guide
Really nice custom build. Great job! 👍👍👍
thanks
Nice rescue of the dead saw. As many have mentioned, the slower speed opens up other uses for it too. Plus later on you could probably and various size pulleys to open up other speeds for it and even more uses (like the 3 pulley system we used in my high school drill press machines, so we could pick the best speed for the drill size and material))
Yeah your right. Thinking of changing it with a 1hp motor and look for a higher rpm ang pulley.
Sir anu size ng belt na nilagay mo? Salamat.kc sira din ang aking speed cutter.pwede pla ganyan sa idea mo.ang galing mo.
Sukatin molang ng medida sir pulley to pulley. Wag sa lubog mag sukat dapat dun sa taas. Kunware nakuha mo 30inches yung sabihin mo sa autosupply
Maestro excelente su idea y buena maquina ,una observación ningún motor o máquina qué lleve bobina se solda material anexó a esta
Change the pulleys. Smaller one on the motor side and larger one on the blade side. Will increase strength although decrease blade speed. Good idea.
Job well done!
You have great videos and this one of them. nice project.
Excelente trabajo. Bueno para recuperar nuestras herramientas en mal estado y darles una segunda oportunidad
Amigo yo tengo una sierra circular pequeña q el eje está barrido en la punta pero está al 100 por ciento. Vi este vídeo y veo q sePude hacer lo contrario. Ponerle buena polea en la punta y hacer un mandril pequeño con su correa y se pude utilizar con un disco de 7 pulgadas xq el motor está en muy buenas condiciones
beau travail.. bravo!
eres un maestro amigo te felicito gracias por subirlo podremos reutilizar las maquinas con un buen motor
try to add some water hose or oil hose for cooling, maybe less spark
Nice diy thanks for sharing ur video
good job.please can you tell the speed of the motor.
De cuantos hp, es el motor que le pusiste a esa cortadora
What power did the engine use?
Great job I won't throw mine away thx
Good save. I wonder how it would work with a small petrol engine?
That would be fun. If i just have that engine im going to try it
Cuantas revoluciones es El motor
subscribed kuyang, pareng, kapatid at idol sek
Great work
If you change the pulleys to slow the speed down that will give it more toque and then you will be able to use a coldsaw blade and because the motor no longer is so close to the blade you will be able to run coolant with the blade just make a reservoir under the saw to catch the coolant and a small pump to cycle the coolant back up to the blade
I would just use a faster motor and run coolant.
If its slow enough like 1500 rpm you could put a carbide blade on it
Most likely 1200 rpm. Ill try that soon bro. Thanks for the info
Yeah carbide blade would be ideal solution. YOu can make it to run with cooland, it will last loong time before resharpening @@SekAustria
exactly what i needed. thank you
Hi, I'm Brazilian, man, I really admire your work. I want to ask what did you do with your channel's previous projects?
Hmmm i confuse with your comment.
@@SekAustria
What did you do with your channel's previous projects?
Hmmm 3d peinter reviews and roller ring bender. Check my channel it seems you missed some of my videos bro.
Buenas tardes.,se puede hacer con una cavesote de la pulidora con motor de la lavadora
How much the hp, rpm, and the Wattage of you motor that you use?
good idea
Idol ilang horse power ung motor mo
Is very good, 👏🏽👏🏽👏🏽
Exelente Trabajo Amigo!!! 👏👏👏
great adaption , need to secure electrical wire from sparks when cutting
\)ช
because it does not put a bigger pulley in the engine because I see that it is very small and thus increases the revolutions
nice pwedepala i convert galingmo kabayan magayanga tulongpo
ممتاز شكرا لك صديقك من بغداد
Really nice job, dude! Great idea!!! 😃
Moter kitane phhes hp rpm kitna hain
Nice job
Paano mo ginawa yung angel grinder mo na maging belt grinder may video ka
Muy buen trabajo mi amigo
Quisiera saber el motor cuantos hp y rpm tiene gracias 👍👍👍👍
Tiene que ser de 1/2 hp para arriba y de alta revoluciones
К Валу на котором крепится диск идёт шестерня которая понижает обороты в 3 раза ,сколько оборотов у Вас на двигателе?
Great idea brilliant ..... it gives me the idea of connecting a three phase motor so I can control the speed or maybe an ordinary DC motor .... I am a true hacker hacker hacker ..... I would use a and grinder with a cut off blade and just saw the motor off and then connect a motor directly to the shaft…… And then find out that I really needed to use a belt based solution …… I am really lazy and this causes me too often do more work than I should have had to do
good job sir
Good job sir
interesante mis saludos desde venezuela
What Should be the Title of this Project? Comment Down :D
Bringing the dead back to life: Tool version
Bagong buhay sa makina de-putol
Ano kaya yon hahaha
Exelente resiclage grasias por compartir su conosimiento
Great video, Thanks for sharing
Sip aku suka 👍👍👍😀😀😀
Y sabes cuántas RPM te bota ese motor
The idea is very interesting, by damaging the original engine, another type of engine can be adapted, possibly the only difference can be the power of the engine or the speed, because the carbons engine has more power and speed, greetings and thanks from Nezaland city Mexico
Genius 👏👏👏👏👏👏👏
How many motor rpm please
that will work good on the roster we here crowing all the time in the back ground lol.
Muito bem feito e funciona perfeitamente bem, meus parabéns, farei o meu assim que possível, vlw ✌!!
بسیار عالییییییییییییییییییییییییییییییییییییییی
идея интересная, но на мой взгляд немного надо доработать,вал более жестко закрепить, дистанционные втулки в виде болтов немного слабоваты. и мотор от стиралки, ремень многоручевой .главное что есть направления и идея.космический корабль не сразу полетел.дорогу осилит идущий
едуард я думаю у него на вале люфт внимателно смотрет видно что диск гуляет
request naman ung dead motor circular saw naman boss ang i convert mo to single phase motor..
Try to use high speed motor ,and make sure that the load speed reaches at least 4500rpm
по моему мало оборотов ,а из за этого сыпется диск ?
Да, только диски крошить....
The new bearing is not steady and cutting speed is too slow as others said. You’ve got a motor, I believe you can make an other new than use the broken one!
Разговора нет., отлично придумано и выполнено. Единственно что лично мне, не совсем понравилось, это то что из мобильного инструмента делают, стационарный (это я про гриндер). По сути из мобильного, сделать стационарный не сложно, а вот наоборот, задача сложная. У переносного инструмента, наблюдается дифицит мощности и надёжности. Тогда как у стационарного, можно варьировать мощностью. И при выходе из строя одного узла, с лёгкостью можно заменить этот узел. (что кстати и продемонстрировал мастер) тут вес уже не важен, зато ремонтопригодность, выросла в разы.
Lodi gawa ka nman Ng pelton turbine generator...request lng Po...
But once I am surprised by his inventions and it gets very good.
👏👏👏desde argentina!!!
Motor details
Eres un genio colega te admiró magnífico muchas gracias maestro buena tarde
very nice 👍
What if the gear brokes
That would be the end i think.
Tenés que cambiarle la corona del motor así tiene más revoluciones porque se ve que le falta fuerza
Por una de mas diametro oh menor para darle mas fuerza
Pues así como está, con esas pocas revoluciones funcionaría mejor con un disco dentado de carburo de Tungsteno.
Усилить место крепления шкива и будет большой ОК !
Great man
ayos yan kuya, ang galing,
Use a carbide tooth blade like the famous evolution chow saw and slow down the rpm to no more the 2300 rpm I copied your idea using a treadmill motor and it's the best metal chop saw I have ever used. I use it more than my horizontal band saw
Aqui no Brasil ,farei o mesmo, pois uma policorte Black Decker , queimou o induzido e me cobraram US $ 68 para fazer o conserto . O custo do equipamento novo é US $ 125 !
oie que buen ingenio brother en lugar de repararla le pusite motor monofasico genial siempre e dicho los hombres somos ingeniosos
Napakahusay!
Sao không chế thành cái máy cắt sắt lưỡi hợp kim tua chậm
Why don't you try running a carbide steel cutting blade like the new cold saw Fein Slugger or Evolution saw and use one of those blades on that belt drive saw that you've created there it might work really well the RPM seem to be just about right they're only supposed to be 15 1600 RPM James
素晴らしい再利用と改造ですね。
しかし、火花が飛んでいく先のケーブルが断線しそうで怖い。
Great idea...
Dude when you said you may change out for a better motor in the future...it just hit me.... find an old chainsaw and use the engine from that... gas powered!!... that would be really cool I've got one here at my house that would work well but I'm in the USA
Haha yes that will be fun and cool. If i have that engine for sure ill replace ut right a way. Thanka man.
@@SekAustria wondered what it would cost to ship my chainsaw to you I'm assuming you're in Austria
Im in the philippines austria is my surname bro. I love to have that i think its kinda expensive to send it to me.
I would like such a welding machine
Es mucho trabajo para adaptarle el motor y el costo de este, con poleas y materiales, sugiero mejor una cortadora nueva.
Si el motor esta arriba de los $1000 mil pesos mas el trabajo